XtendLan NVR-1602F User manual

NVR-902F
Network digital video recorder
User manual

1
1. Front Panel
The front panel of 1.5U/2U is shown as follow:
Name
Icon
Function
Power Button
ON/OFF
To boot up or shut down the NVR
RESET Button
RESET
Take reset operation
Power indication light
POWER
Light will be on after power up
Network indication
light
LINK
The NET light indicates the network connected normal
USB
To connect USB mouse, Mobile HDD,USB Storage drive etc.
2. Rear Panel
1U rear panel
1.5U rear panel
1 2 3 8 9 4 7 6
Power switch
5
1 2 3 8 9 4 7 6
10 5

2
2U rear panel
The rear panel of port function is shown as follow:
Item No.
Parameter
Description
1
Video output
Composite video broadcast signal(CVBS) output port
2
Audio output
Audio signal output port
3
Talk back
Audio input for talk back
4
Network port
RJ-45 Network port
5
VGA port
VGA video signal output port
6
Power supply input
Power supply input port(1U with DC12V,1.5U/2U with 220V)
7
Connecting terminal
Include alarm input, alarm output,RS-485 port
8
HD port
HD Video signal output port
9
USB
To connect USB mouse, Mobile HDD,USB Storage drive, etc.
10
ESATA port
ESATA HDD port
3. Rear panel I/O port connection
Picture 1
Picture 2
1 2 4 3
1 3 4
1 2 3 8 9 4 7 6
10 5
2 2

3
Rear panel I/O port function is shown as follow:
Item No.
Parameter
Description
1
Alarm input
Alarm input port, connected to the alarm
2
GND
Ground port
3
Alarm output
Alarm output port
4
RS-485
RS-485 output port, connected to the PTZ

- 1 –
Preface
Attentions:
Welcome to use our digital video recorder. For your secure using, please read this
user manual carefully. The following contents are about the proper use of the
product, the prevention of danger and loss of property etc. Please be sure to
abide.
Do not touch the power switch and the DVR by wet hands or wet objects,
in order to avoid electric shock;
After installing the host, please make sure that the host and the chassis
are connected to the ground in order to avoid video and audio signal
interference and damaged by static electricity;
Ensure the voltage stability of the power supply of the DVR. Use the power
input with stable voltage value and little wave interference rather than
shutdown the DVR by disconnecting the main switch directly;
Do not drop any liquid or metal on the DVR in case short circuit inside or
fire;
The device does not include any hard disk, and you need to properly
install the hard disk before using it, otherwise, you cannot record and
playback the video;
The dust on the mainboard will cause short circuit when it is damp. In
order to ensure the long-term normal working, you should regularly dedust
the mainboard, connectors, chassis, fan and so on by a brush;
Do not disconnect the power switch directly when you want to shutdown
the DVR. You should use the shutdown button on the panel in order to
avoid damage to the hard disk;
Do not open the device when it is connected with electricity;
To ensure the integrity of the recording data, please replace the hard disk
when it is damaged (there is disk error record in the log information).
This user manual offer references to multi-series products. The specific
operation of each product will not be listed one by one. Please contact our
technical department when you have any question.

- 2 -
Contents
1. Product Instruction................................................................................3
2. Installation Instruction...........................................................................3
2.1 Open-case Inspection .................................................................3
2.2 HDD Installation ..........................................................................3
2.3 Front Panel and Rear Panel InstructionChyba! Záložka není
definována.
3. Local Operation Guide..........................................................................4
3.1 Start/Shutdown System...............................................................4
3.2 System Login...............................................................................4
3.3 Menu Operation...........................................................................5
3.3.1 Start Setup......................................................................11
3.3.2 Display Setup..................................................................12
3.3.3 PTZ Setup.......................................................................12
3.3.4 System Setting................................................................13
3.3.4.1 Device Parameters ..............................................14
3.3.4.2 Channel Parameters............................................14
3.3.4.3 Network Parameters ............................................16
3.3.4.4 Alarm&Exception..................................................19
3.3.4.5 Account Parameters.............................................19
3.3.4.6 HDD Settings .......................................................20
3.3.4.7 System Management...........................................20
3.3.4.8 Device Log...........................................................21
3.3.5 Playback.........................................................................21
3.3.6 Record Backup...............................................................22
3.3.7 Manual Record ...............................................................23
3.3.8 Alarm Information ...........................................................23
3.3.9 Snapshot.........................................................................24
3.3.10 File Manager.................................................................24
4 Network Operating Instruction .............................................................25
5 Mobile View Operation Guide..............................................................26
5.1 Client Software Obtaining..........................................................26
5.2 The Parameter Settings of the DVR which Supports Mobile Surveillance
.........................................................................................................26
5.3 Android Mobile System .............................................................26
5.4 Blackberry Mobile System.........................................................28
5.5 Symbian Mobile System............................................................30
5.6 Windows Mobile System...........................................................32
5.7 iphone Mobile System...............................................................33
6 Appendix ..............................................................................................35
6.1 HDD Capacity Calculation Method for Reference.....................35
6.2RemoteControlInstruction..............................................................37
6.3TechnicalData...........................Chyba! Záložka není definována.

- 3 –
6.4 Common Problems Resolution .................................................42
1. Product Instruction
1.1 Product Summary
This device is a video coding and recording product specially designed for the
video monitoring field, combining with H.264 video compression, large
capacity HDD storage, TCP/IP network, embedded Linux operating system
and other various advanced electronic information technologies, realizing
high-quality image and low bit rate recording features and favourable system
stability.
The device meets the standard of GB 20815-2006 “Video Security
Surveillance Digital Video Device” issued by the government. This device has
multiple functions including recording, playback and monitoring
simultaneously, realizing synchronous video and audio, with advanced
control technology and powerful network data transmission ability.
1.2 Main Functions
The following functional characteristics will be different due to the different
series of products and their different hardware versions.
Real-time Monitoring
Compression Processing
Function
Recording Function
Video Playback and Backup
Camera Control
Alarm Management and Control
Communication Port
Network Function
2. Installation Instruction
2.1 Open-case Inspection
When you receive the product, please check all the things according to the
DVR packing list in the box.
2.2 HDD Installation
Installation Preparation:
Need one cross screwdriver. This series of HDD DVR can install 2 to 8 pieces
of HDD inside, and the capacity of each HDD can be up to 2TB.
HDD Installation Steps:

- 4 -
Twist off the screws on the side panel of the case and then open the cover of the
chassis.
Fix the HDD on the HDD screw whole sites of the baseboard with screws.
Connect the HDD data cable and power cable.
Cover the case, fix it with screws.
3. Local Operation Guide
3.1 Start/Shutdown System
3.1.1 Start System
Plug power cable, press power switch, the power led will be on and the DVR
will start. After booting, the video output default to multi-window output mode.
If the booting time is within the record setting time period, the system will auto
enable the record function.
Notice: Please use the DVR matching power supply instead of any other
power supply of any other type or brand.
3.1.2 Shutdown System
Click →click Shutdown. (Note: this method is suggested when
shutdown device in order to avoid damage to the device from electricity
cut-off by accident).
Notice: Before changing the HDD operation, you should shutdown the device
and cut the power supply first and then operate.
3.1.3 Power Failure Recovery
When the DVR is under the recording status, if the system power is cut off or
the device is shut down forcefully, after reconnected with the power supply,
the DVR will auto-save the video before cutting and auto-recover to the
previous status and continue to work.
3.2 System Login
After normal booting, single-click or press the OK key on the remote
control to pop-up the login dialog box, user input the user name Admin and
password 888888(default login password) in the input box.

- 5 –
3.3 Menu Operation
When the user logins the system successfully, click the right mouse button：
Preparation before configuration: before configure the IP channel,
please make sure that the IP device has been connected with the
network of the NVR and the IP device is in the same network section
as the NVR.
3.3.1 Configuration of the IP Channel
First method: auto search IPC
1. Click “Remote Setting”will show the below interface:

- 6 -
2. Check “Enable”, click “Search”, the IP address, protocol and port number
of the IPC will appear, as shown in the below picture:

- 7 –
3. After double-click, fill in the password in the password field.
4. Click “Save”. The image will appear on the preview interface, as shown
in the below picture:

- 8 -
Second Method: add IPC manually.
1. Click “Remote Setting”will show the below interface:

- 9 –
2. Check “Enable”, edit the IP address and port number. Select protocol and
mode. Edit user name and password. Click “Save”finally.

- 10 -
3. The image will appear on the preview interface, as shown in the below
picture:

- 11 –
press the buttons on the front panel, or press the [MENU] key on the
remote control to enter the menu interface.
The menu consists of start, display, PTZ, configuration, playback, backup,
manual record, snapshot and document:
The device enters the real-time monitoring screen after normal booting.
There are superposed date, time, the channel name of every channel. Icons
of record, 3D positioning and alarm status will appear in the right upper
corner.
3.3.1 Start Setup
Click , and the interface will display:
1) Shutdown: Click “Shutdown” button, the device
will shutdown.
2) Reboot: Click “Reboot” button, the device will
reboot.

- 12 -
3) Logout: Click “Logout” button, the device will logout.
4) Lock: Click “[ ] Lock” , the menu will be locked.
3.3.2 Display Setup
Click , the interface on the right will show:
Screen Type:
1) Language: Different languages for selection
(For example: Simplified Chinese, Traditional
Chinese and English).
2) Skin: There are original version and blue for
selection.
3) Screen mode: Select different screen modes.
4) Rotation Interval: Setup the time interval of rotation. Tick “Enable SEQ”
to start rotation.
(Note: the rotation function can only be enabled under 1 screen)
3.3.3 PTZ Setup
Click will show the below interface:
3.3.3.1 PTZ Control
Before starting the PTZ control, please firstly confirm the PTZ parameter
settings, PTZ protocol and the correct connection of the 485 control line etc.
After setting the parameters, select the
channel which you want to control in the
preview interface, then control the
left-handed rotation, right-handed rotation,
up regulation, down regulation of the lens;
zoom in and zoom out of the focal length;
zoom in and zoom out of the focal point;
zoom in and zoom out of the iris; setting of
the PTZ speed.
3.3.3.2 PTZ Setup
1) Preset setting: first turn the camera to the needed position through the
direction buttons of the PTZ control, then select a preset number, and

- 13 –
click “Settings” button. “Preset” call: select a preset number which needs
to be called, and click “Call” button.
2) Cruise setting: select a cruise number, click “Settings”, as shown in the
below interface:
In the cruise setup interface,
select preset point, cruise time,
cruise speed, click “Add” button,
then the preset point of the cruise
path is added successfully
(multi-preset points can be added).
Click “Delete” button can delete
the preset point of the cruise path.
“Cruise” call: select a cruise
number click “Call” button.
“Cruise” delete: select a cruise
number , and click “Delete” button.
1) “Track” setup: select a track number, and click “Set” button, then start
the PTZ control operations, and then click “Stop”, and the track is
remembered successfully.
2) “Track” call: select a track number, and click “Call” button.
3.3.4 System Setting
Click , and the below interface will show:

- 14 -
3.3.4.1 Device Parameters
[Device Info] Check and modify the basic information of the device.
[System Version] Check the basic information of the device system.
[RS232] Can set RS232 serial port.
[RS485] Can set the RS485 serial port.
[DST Setting] Tick “DST” check box, then click the set button to set the start
time and end time of DST.
3.3.4.2 Channel Parameters
[Display Settings] The configuration parameter of every channel can be
modified.
1) Camera Name: You can modify the name of the specified channel.
2) Time Format: You can select different time formats for the specified
channel.
3) Date Format: You can select different date format for the specified
channel.
4) Display Week: Can select different week display status for the specified
channel.
5) OSD Position: You can select any position for the OSD of the specified
channel.
6) Display Parameters: Can set the brightness, contrast, saturation and
hue for the specified channel.
7) Video Format: There are PAL and NTSC for selection.

- 15 –
8) Copy To: Copy the configuration parameters to other channels.
[Video Parameters] The setting parameters of every channel can be
modified.
1) Encoding Type: Main Stream(Normal), Sub Stream, Main Stream(Event)
for selection.
2) Stream Type: Video, Video&Audio for selection.
3) Resolution: There are CIF, 4CIF, 2CIF etc, for selection.
4) Bitrate Type: Constant and Variable for selection.
5) Frame Rate: Select different value from the drop-down list, the default
value is “Full Frame”.
6) Video Quality: Select different image quality as needed, it is default to
“Highest”.
7) Copy To: Copy the configuration parameters to other channels.
[Schedule Record] You can set different types of record plan for each
channel.
1) Enable Recording: Tick the small box before “Enable Recording” will
start recording.
2) All Day Recording: Tick the small box before “All Day Recording” to start
all day recording, then you can select schedule recording, motion
recording, alarm recording, command recording etc.
3) Record Time: You can setup by 8 separate time periods.
4) Advanced Settings: You can set the prerecord time and post record
time.
5) Copy To: Copy the configuration parameters to other channels.
[Motion Detection] The parameters of each channel can be modified.
1) Area settings: Select the motion detection area, press the left mouse
button and drag to the area which you want to set motion detection, click
OK.
2) Alarm Schedule: Set the time intervals of alarm.
3) Linkage: Select the linkage way which you need.
4) Copy To: Copy the configuration parameters to other channels.
Onvif protocol does not dupport above function
[Video Lost] Can modify the parameters of each channel.
1) “Alarm Schedule”: Set the time intervals of alarm.
2) “Linkage”: Select the linkage way which you need.

- 16 -
3) “Copy To”: Copy the configuration parameters to other channels.
Onvif protocol does not dupport above function
[Video Tampering] The parameters of each channel can be modified.
1) Area settings: Select the motion detection area, press the left mouse
button and drag to the area which you want to set motion detection, click
OK.
2) Alarm Schedule: Set the time intervals of alarm.
3) Linkage: Select the linkage way which you need.
4) Copy To: Copy the configuration parameters to other channels.
Onvif protocol does not dupport above function
[Video Mask] The parameters of each channel can be modified.
1) Area settings: Select the motion detection area, press the left mouse
button and drag to the area which you want to set motion detection, click
OK.
2) Copy To: Copy the configuration parameters to other channels.
Onvif protocol does not dupport above function
3.3.4.3 Network Parameters
[Network Settings] The network basic parameters of the device can be
modified.
1) NIC Type: there are different network card types for selections.
2) IP: enter corresponding numbers to modify the IP address.
3) Obtain Auto: Auto search IP function. When open DHCP, the IP/Subnet
Mask/Default Gateway cannot be set; If the current DHCP is valid, then
the IP/Subnet Mask/ Default Gateway will show the value obtained by
DHCP; if the current DHCP is invalid, IP address etc. will show 0.
4) Device Port: Enter the corresponding device port.
5) Subnet Mask: Enter the corresponding IP subnet mask.
6) Default Gateway: Enter the corresponding gateway address.
7) MAC: Display the MAC address current network port.
8) HTTP Port: It is default to 0.
9) Multicast: Enter the corresponding multicast address.
10) Enable Wi-Fi: Tick the box before “Enable Wi-Fi”and click “Wi-Fi”, and
enter the following interface: