xtpower MP-10000 Parts list manual

Istruzioni pacco batterie_EN;Jan14
DESCRIPTION USE OF BATTERY PACK MP-10000 EN
Instructions for rec arging
1. Remove all components from packaging and check any visible damage of the device.
2. Connect battery pack to mains power supply (AC 100-240V 50/60hz) as shown below.
3. Connect power supply to battery pack in connector INPUT
4. Connect power supply to main socket.
5. Recharging time is 5 hours approximately.
1 Battery pack
2 Power supply for battery pack recharging
INSTRUCTIONS FOR BALANCE CONNECTION
1 Power supply of balance.
2 Cable connection balance battery pack
3 Selector output voltage of battery pack. (Select 9V)
1. Place the selector (3) at 9V indication on the upper side of battery pack.
2. Connect provided connection cable (2) in connector OUTPUT of battery pack.
3. Connect the other end of the cable (2) to balance power outlet.
4. Press power button on battery pack (4).
5. Duration of charging is 40 hours appromately.
1
2
1
2
3
4

MP-10000
www.xtpower.de 140617
Manual
Thanks a lot !
This product is a rechargeable battery (Power Bank) that can be used
to power mobile devices. The stored energy after full charge is about
37Wh which will be provided with an output voltage of 5V from the
USB output. Additionally power will be provided by a DC Output with
9V and 12V.
For the best use of the power bank and for your safety, please read
these instructions carefully before using the power bank.
Safety
-Please only use the supplied power adapter for charging,
otherwise you may cause damage to the device.
-The product is not suitable for children as it contains fragile and
small parts that can be swallowed easily.
-Please do not drop and do not immerse in water as the unit will
be damaged.
-Do not expose to high temperatures or flammable gases.
-Please do not remove the housing.
-Please don’t directly connect any contacts as this can lead to
short circuits.
Warnings:
-The unit may explode near or in an open flame.
-The unit should not be opened.
-Rechargeable batteries must not come into contact with liquids.
-The Power Bank should not be short-circuited or brought into
contact with metal
-Operating temperature range -20 ° C and max. 45 ° C
-Please keep batteries out of reach of children
-Don’t put batteries in your mouth
Warranty and Liability:
-If there is a problem with the device, please contact your
dealer.
-The manufacturer is not liable for injury or damage caused by
improper use.
-Modification of the product, misuse or unauthorized repair will
void the warranty.
-XTPower reserves the right to make changes to the product or
the instructions and manuals without prior notice.
Attention:
On the front side there is some protective foil to cover this side during
production and transportation. This protective foil needs to be taken
off for usage.
Specification:
Type: Lithium-Polymer
Capacity: 10.000mAh/3.7V/37Wh
Output Voltage: 5V / 9V /12V
Output Current: 2 x USB 2100mA; DC 2000mA
Connections:
2 x USB-Output (OUT S / OUT I)
1x DC Out (OUTPUT)
1x DC In (12V INPUT)
Power Adapter
Input Voltage 100-240V 50/60Hz
Output Voltage 12V 1000mA
Dimensions: 120 x 80 x 23 mm
Weight: ca. 304g
Accessories
-Powerbank XTPower MP-10000
-USB spiral cable
-10 adapter (u.a. Micro-USB, Mini-USB, PSP, NDS
Nokia N70, LG KG800, Sony K750, Samsung G600, Samsung
D800, Apple iPhone/iPad/iPod)
-6 Notebook and Netbook Adapter
A = Sony
B= Toshiba, NEC
C= IBM, Acer, Toshiba
D= HP, NEC, Compaq, Asus
G= Acer, Benq
H=Samsung
-Car Charger 12V
-Power Adapter with EU plug in
Disposal
-Batteries and Power Banks should not be disposed of with
household waste.
-Recycling and disposal of waste batteries and Power Banks
make an important contribution to protect our environment.
-Batteries Directive: 2006/66/EC
CE Declaration of Conformity:
-This product bears the required CE marking according to
Directive 2004/108/EC. The product meets the essential
requirements of the European directives and regulations.

MP-10000
www.xtpower.de 140617
Battery Indicator:
-Press of the switch button (on / off) which turns on the power
bank and gives you a charge indication
-The 4 LEDs indicate the current state of charge. More lit LED’s,
indicate a higher state of charge.
-The LED’s turn off after 3 sec.
Charging the Power Bank:
-Your Power Bank comes partially charged. Please charge the
new power bank completely before using.
-Connect the powerbank with the power adapter using the DC
Input and connect with a power line.
-The active charging function is indicated by a flashing LED. The
number of lit LEDs shows the current charge level of the power
bank during charging.
-Don’t store the power bank in fully discharged state for long
periods of time, please recharge from time to time.
Charge your mobile device using USB jack (OutS / OutI):
-Take the USB plug of the supplied USB cable and connect it to
the USB port of the power bank.
-Connect the USB cable with your device choosing the correct
adapter.
-You can also use the original USB cable of your device in case
your device needs a different connector.
-Briefly press the switch button (on / off), your mobile device
will now be charging.
-When your device is fully charged (<50mA charging current) or
the Power Bank is not being used, the Power Bank switches off
automatically.
Load your mobile device via the DC jack (Output)
First select with the switch mounted on the side the required voltage
(9V/12V).
! Important: Choose the correct output voltage of 9V or 12V before
connecting the device to be charged, as this can be damaged if you
choose the wrong voltage.
- Connect the round plug adapter cable with power bank (output).
- Find the appropriate connector for your device and connect it to
the cable.
- Turn on the power bank as described above
- Your device is now loaded. The four LEDs on the Power Bank indicate
the current charge status of the Power Bank.
- once your device is fully charged (<50mA charge current) or the
capacity of the power bank is used up, the power bank will
turn off automatically.
If consumers are connected to draw a current that is above the
specified values, the power bank will turn off for security reasons.
If consumers are connected which only need a small current which is
below the current of the charger used to detect the end of charge,
then the current will also turn off after a short time and the device
unfortunately cannot be loaded or operated with this power bank.