Yaesu FT3DR User manual

C4FM/FM 144/430MHz
DUAL BAND DIGITAL TRANSCEIVER
FT3DR
FT3DE
Instruction Manual (WIRES-X Edition)

2
Contents
What is WIRES-X? ............................................................................................................................3
Terminology ................................................................................................................................4
Connecting to a Faraway Station Using WIRES-X ........................................................................7
Finding a local node .......................................................................................................................7
Connecting in digital mode .............................................................................................................7
Connecting to a WIRES-X digital node ......................................................................................7
Connecting to the other node ID or the other room ID ...............................................................7
Connecting to a node or room on the Internet..........................................................................10
Communicating with others ......................................................................................................13
Useful functions in digital mode....................................................................................................14
Using preset channels..............................................................................................................14
Connecting to registered nodes or rooms ................................................................................15
Releasing the WIRES-X connection.............................................................................................17
Connecting to analog nodes.........................................................................................................18
Connecting to nodes or rooms on the Internet .........................................................................18
Communicating with others ......................................................................................................19
Disconnecting from the node or room ......................................................................................19
Various display functions..............................................................................................................19
Confirming the location of the local node and the partner station ............................................19
Confirming the frequency .........................................................................................................19
Returning to the initial screen...................................................................................................19
Using the News Function of WIRES-X..........................................................................................20
Viewing messages........................................................................................................................20
Viewing text data in local nodes ...............................................................................................20
Viewing text data on the WIRES-X server (INT NEWS)...........................................................22
Viewing text data in nodes or rooms on the Internet ................................................................23
Importing images..........................................................................................................................25
Importing images from local nodes ..........................................................................................25
Importing images from the WIRES-X server (INT NEWS) .......................................................25
Importing data from nodes or rooms on the Internet ................................................................26
Viewing imported data later..........................................................................................................26
Deleting imported data .................................................................................................................27
Deleting a file............................................................................................................................27
Listening to audio messages........................................................................................................28
Listening to emergency information in the local node ..............................................................28
Listening to routine messages in local nodes...........................................................................29
Listening to routine messages on the WIRES-X server (INT NEWS) .....................................29
Listening to emergency information in nodes or rooms on the Internet ...................................30
Listening to routine messages in nodes or rooms on the Internet............................................30
Transmitting messages and images.............................................................................................31
Creating and transmitting messages to local nodes.................................................................31
Transmitting saved messages or images to local nodes..........................................................33
Creating and transmitting messages to nodes or rooms on the Internet..................................33
Transmitting saved messages or images to nodes or rooms on the Internet...........................33
Transmitting audio messages.......................................................................................................34
Transmitting emergency information to local nodes.................................................................34
Transmitting routine voice messages to local nodes................................................................34
Transmitting emergency information to nodes or rooms on the Internet..................................35
Transmitting routine messages to nodes or rooms on the Internet ..........................................35
WIRES-X Setting Mode Menus ......................................................................................................36
WIRES-X setting mode list ...........................................................................................................36
Using the WIRES-X setting mode ................................................................................................36
Setting the operating frequencies for repeaters/WIRES-X.......................................................36
Setting the item order on the node & room lists .......................................................................37
Editing category names............................................................................................................37
Deleting the registered nodes and rooms ................................................................................37
The DG-ID feature to access the WIRES-X node station.........................................................38

3
What is WIRES-X?
WIRES (Wide-coverage Internet Repeater Enhancement System) is an Internet
communication system which expands the range of amateur radio communication. By
relaying radio signals via the Internet, stations can be connected where radio waves
cannot reach each other.
WIRES uses local nodes (stations connected to the Internet via PCs) as access points
which repeat communications of conventional amateur radio stations. When the local
nodes are connected to each other via the Internet, amateur stations all over the world
can communicate with each other just by connecting conventional stations to the local
nodes.
Local node Local node StationStation
Internet
In addition to the WIRES features, WIRES-X also supports digital communications. Using
WIRES-X, you can transmit and receive digitalized data such as text, image data and
audio.
Using the WIRES-X in conjunction with the transceiver allows you to have analog/digital
communications with stations outside the communication range. In digital communication
mode, you can search stations by call signs or keywords, and exchange data such as
messages and location information.

4
Terminology
■Node
Radio repeater connected to the Internet via a PC, which repeats communications of
conventional amateur radio stations as an access point
zLocal node
Node within the radio communication range of a conventional amateur radio station
zAnalog node
Node which is a transceiver or repeater using the conventional FM format and can only
repeat DTMF (Dual Tone Multi Frequencies) codes and analog audio transmissions/
receptions
zDigital node
Node which is a transceiver or repeater compatible with digital communications in C4FM
(Continuous 4 level FM) format. With this type of node, you can transmit/receive audio
as well as text and image data. You can also repeat DTMF codes and analog audio
transmissions/receptions.
Local
node
Local
node
Local
node
Local node Local node
Local
node
Local
node
Local
node
Local
node
Local
node
Station Station
WIRES
server
HRI-200
PCPC
Internet connection
HRI-200
As long as the local nodes
are linked to each other, stations
can communicate with each
other by connecting to a
local node

5
■WIRES-X user ID
YAESU provides identification names with the WIRES-X nodes. For each node, a DTMF
ID (5-digit number) and user ID (alphanumeric characters consisting of up to 10 digits)
are provided.
If you know the ID of the node you want to connect with, you can transmit the DTMF
code from the transceiver, and directly specify the node to connect to by searching by
characters (only for digital nodes).
zID list
Nodes and rooms which are currently operating WIRES are listed and published on our
website. We provide information such as IDs, call signs and operating frequencies (some
may not be published due to the wishes of owners).
■Room (Round QSO Room)
WIRES system community space to which multiple nodes can connect simultaneously.
As well as voice communications, you can also chat with text messages on the PC used
for the local node.
zOpen room
Room which allows all nodes to connect to
zClosed room
Room only registered nodes can connect to
zOwner
Node which opens and organizes a room
zActivity
Nodes currently connected to a specific room
D
DD
D
AA
JF7XXX
-ND3
JQ1YBF-ND1 JA2YSO-ND2
JH4XXX
-ND4
JA2-ROOM
JQ1YBF-ND1
JF7XXX-ND3
JA1XXX-S1
* Currently
3 activities
in this room
JA1XXX
-S1
JA2XXX
-S2
WIRES
server
HRI-200
PCPC
Internet connection
HRI-200
When a local node
connects to a room,
stations already connected to
that node are also connected
to the room
Tip In the illustration,
D
refers to digital nodes and
A
refers to analog nodes.

6
■News function
This feature allows you to save digital data such as text, image and audio data on the PC
used for the local node, and access the data from the connected digital station.
From the digital transceiver, you can access the local node (LOCAL NEWS) and the data
storage area (news station) in the node or room you connect to, and import (upload) and
export (download) data.
The owners of a node or room can import/export data from/to their own station via a PC.
The owner can also delete data and change information such as its name and attribution.
The WIRES-X server also has its own news station (INT NEWS) where you can read
information and data supplied by YAESU.
D
DD
D
JF7XXX
-ND3
JQ1YBF-ND1 JA2YSO-ND2
JH4XXX
-ND4
JA2-ROOM
Local news
Audio messages
(emergency)
News Station
Audio files
Te xt data
Images
Local news
Audio messages
(emergency)
News Station
Audio files
Te xt data
Images
INT news
Audio messages
(emergency)
News Station
Audio files
Te xt data
Images
Connecting to a node
allows you to access data
in the local node, the WIRES-X
server, and a node or room
on the Internet
Data on the WIRES-X
server is only for
downloading
JA1XXX
-S1
JA2XXX
-S2
WIRES
server
HRI-200
PCPC
HRI-200
Internet connection
■Preset search function
If the preferred channel for connecting to a local node is programmed (preset) in the
transceiver, the channel can be scanned automatically when you start up WIRES-X.
Utilize this function as follows:
•Quickly connect to the local node you usually access by presetting its frequency in
advance.
•By presetting to a shared channel frequency with your friends nodes, you can quickly
connect the transceiver to a local node even while you are traveling in other areas.
You can use two transceivers as nodes, one for the preset search channel (receive only
channel) and the other for the voice channel (operation channel).

7
Connecting to a Faraway Station Using WIRES-X
Finding a local node
To communicate using WIRES-X, a WIRES-X node station (local node) must be
established within radio contact range of the user transceiver.
WIRES-X nodes are stations users voluntarily registered with Yaesu. Their information
such as locations and operation styles are listed on our website:
https://www.yaesu.com/jp/en/wires-x/index.php
First use this list to search for a nearby local node, and nodes on the Internet used by
people you want to communicate with; write down the node names and frequencies.
Since the connection procedure differs between digital stations and analog stations,
confirm whether the node is an analog station or a digital station.
•When the local node is a digital station:
Connect from your transceiver in digital mode.
(Nodes on the Internet can connect to both digital and analog stations.)
•When the local node in an analog station:
Connect from your transceiver in analog mode.
(Nodes on the Internet can connect to both analog and digital stations.)
Connecting in digital mode
•Ascertain the DSQ code or the DG-ID setting of the WIRES-X node station. Connecting
to the WIRES-X node requires the transceiver DG-ID be set according to the DSQ code
or the DG-ID code set on the WIRES-X node station.
•Confirm that the operating mode of WIRES-X node has been set to the C4FM digital
mode.
•Before using WIRES-X, set the communication mode (modulation mode) to C4FM.
Connecting to a WIRES-X digital node
1Set the transmit/receive DG-ID to the same ID number as the node station. For details,
refer to the FT3DR/DE Operating Manual.
2Transmit corresponding to the transmit/receive fre-
quency.
Tips  •Ifreceivingthesignalfromthenode,transmititasis.
•If not receiving the signalfrom thenode, itis possible
that the node station is not connected to the Internet à
proceed to step “Connecting to the other node ID or the
other room ID”.
5 DG-ID
DG-ID: AUTO
Connecting to the other node ID or the other room ID
1Press and hold the [DISP]key→Touch[WIRES-X]→[5 GD-ID].

8
The WIRES-X DG-ID setting screen will be displayed.
2Rotate the DIAL knob to set the WIRES-X DG-ID to the same ID number as the node
station.
AUTO: Only open nodes, set to the DG-ID number “00” may be connected.
01 to 99: Only nodes matching the set DG-ID number may be connected.
3Press the PTT.
Returns the screen to the frequency display screen.
4Rotate the DIAL to set the A-band to the frequency of the desired local node.
Caution
WIRES-X can only be used on the A-band.
If using the B-band (shown on the bottom part of the screen) as the operation band, pressing the [
X ]
key automatically switches the operation band to the A-band (shown on the top part of the screen).
5Press the [ X ] key.
[
X ] flashes on the left side of the frequency display.
Tip  •While[ X ] is flashing, briefly press the [ X ] key to re-establish connection to the local node.
•Whenanylocalnodecannotbefound,[
X ] will disappear in 30 seconds.
When a local node is found, [ X ] is lit solid, and the node name and city name appear
on the bottom part of the screen.
Tip Depending on the connection status, the screen will show one of four display patterns.
(1) Connected to the local node, but unable to connect
to Internet nodes or rooms (never before established
connection to Internet nodes or rooms)
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
(2) Connected to the local node, but unable to connect
to Internet nodes or rooms (previously succeeded in
establishing connection to Internet nodes or rooms)
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345

9
(3) Connected to the local node, successfully connected to
an Internet node or room (the Internet node or room is
the same as the one most recently used)
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345 24
(4) Connected to the local node, successfully connected to
an Internet node or room (the Internet node or room is
different from the one most recently used)
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JH1YPC-ND
When is displayed, rotate the DIAL. Call signs of
nodes and rooms on the Internet you previously
connected to flash.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345 24

10
Connecting to a node or room on the Internet
You can connect to the desired node or room in one of the following ways:
•Selecting an accessible node or room from the list
•Specifying the node name or room name
•Selecting the most recently connected node or room
•Specifying the DTMF ID of the node or room you want to connect to
zSearching from the node & room lists
1While displaying the local node, touch [SEARCH &
DIRECT].
Displays the category list.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
2Touch [ALL].
Displays the list of accessible nodes and rooms.
Tips  •Connectiondestinationsaredisplayedfromtheroomlist
and then node list.
•On the connection destination room columns, the
number of activities (the number of nodes connected to
each room) appears on the right side.
C1:----------------
C2:----------------
C3:----------------
C4:----------------
C5:----------------
3Touch the node or room you want to connect to.
Starts connection.
Tip Rotate the DIAL to select the node or room you want to
connect, then press PTT to establish a connection.
CQ-OPEN-ROOM 194
JA1YOE-TKY-ROOM 21
JA1YOE-ROOM-B 16
JA1YOE-ROOM-C 9
JQ1YBG-13-ROOM-B 8
ALL [999]
Once connection is successfully established, the
menu list of the node (room) you are connected to will
appear.
Tip If connection is unsuccessful, an error message appears
and the screen returns to the list of nodes and rooms.
JA1YOE-TKY-ROOM
NEWS STATION
EMERGENCY
LOCAL NEWS
INT NEWS

11
zSearching by node or room name
1While displaying the local node, touch [SEARCH &
DIRECT].
Displays the category list.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
2Touch [SEARCH & DIRECT].
Displays the character input screen. C1:----------------
C2:----------------
C3:----------------
C4:----------------
C5:----------------
3Enter all or part of the room or node name.
The characters you have just entered appear on the
screen.
4Touch [ENT].
If connection destinations with the first part of a name
partially matching the name you entered are found,
they will be listed.
Tips  •If there is no connection destination matching the
entered name, “No Matches
” appears and then the
screen returns to the character input screen.
JA1Y
•If the name you entered is found, the transceiver
establishes connection immediately.
•Thescreendisplaystheroomlistsearchresultsfollowed
by the node list search results.
•Ontheroomcolumnsinthesearchresults,thenumber
of activities (the number of nodes connected to each
room) appears on the right side.

12
5Touch the node or room you want to connect to.
Starts connection.
Tips  •RotatetheDIALtoselectthenodeorroomyouwantto
connect, then press PTT to establish a connection.
•Onceconnectionissuccessfullyestablished,themenu
list of the node (room) you are connected to will appear.
•Ifconnectionisunsuccessful,anerrormessageappears
and the screen returns to the list of nodes and rooms.
JA1YOE-TKY-ROOM 21
JA1YOE-ROOM-A 4
JA1YOE-ROOM-B 3
JA1YOE-ROOM-C 0
JQ1YBG-ND
JA1Y [ 24]
zConnecting to the node or room you have most recently connected
If you have previously connected to a node or room on the Internet, it appears and flashes
at the bottom of the screen.
Touch the flashing node or room to start connection, and once connection is established,
the menu list of the node (room) you are connected to will appear.
If is displayed on the left side of the node name at the
bottom part of the screen, rotate the DIAL to display the
node most recently connected.
Tip If connection is unsuccessful, an error message appears and
the name flashes again. SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345 24

13
zSpecifying the DTMF ID of the node or room you want to connect to
1While displaying the local node, touch [SEARCH &
DIRECT].
Displays the category list.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
2Touch [SEARCH & DIRECT].
Displays the character input screen. C1:----------------
C2:----------------
C3:----------------
C4:----------------
C5:----------------
3Touch [ID].
Displays the DTMF input screen.
#
4Enter the 5-digit DTMF ID.
5Touch [ENT].
Tips  •Theconnectionbeginsand"Waiting"flashes.
•Onceconnectionissuccessfullyestablished,themenu
list of the node (room) you are connected to will appear.
•Ifconnectionisunsuccessful,anerrormessageappears,
and the screen returns to the node and room list screen.
#22000
Communicating with others
1While displaying the station you are currently
connected to, press PTT.
The transceiver switches to transmission mode.
2Speak into MIC.
3Release the PTT.
The transceiver switches to reception mode.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345 24
Tip
You can communicate with the node or room you are connected to by pressing the PTT even when
viewing data in a node or room on the Internet using the NEWS function in digital mode on page 20.

14
Useful functions in digital mode
Using preset channels
Programming (presetting) a channel frequency allows you to easily connect to a local
node.
By sharing a channel frequency with other nodes, you can connect the transceiver to a
local node even while you are out. This is useful for a group to operate a station.
zPresetting a channel
1Press and hold the [DISP] key.
2Touch [WIRES-X].
Displays the menu list.
3Touch [1 RPT/WIRES FREQ].
4Rotate the DIAL to select [PRESET].
Tips  •Every time the DIAL is rotated, the setting switches
between [MANUAL] and [PRESET].
 •ThedefaultsettingisMANUAL.
5Press the [DISP] key.
1 RPT/WIRES FREQ
PRESET
: 145.375 MHz
PUSH“DISP”
6Rotate the DIAL to select the frequency.
Tips  •Touching[BAND] switches the preset frequency band.
7Press the PTT.
Sets the frequency and returns the screen to the
frequency display screen.
1 RPT/WIRES FREQ
PRESET
: 145.375 MHz
zConnecting to a preset channel
1Follow the procedure in “Presetting a channel” on page 14 to make the preset
channel available in advance.
2Press the [ X ] key.
[
P ] flashes on the left side of the frequency display.

15
When a local node is found, [ X ] lights up, and the
node name and city name appear on the bottom part
of the screen.
Tip When any local node cannot be found, [ P ] disappears in 30
seconds. SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
Tip
If the frequency of the detected local node is different from that of the preset channel, the frequency
automatically switches to the node frequency.
zEnding searching by a preset channel
1Follow steps 1 to 3 in “Presetting a channel” on page 14 to display the selection
items of [1 RPT/WIRES FREQ].
2Rotate the DIAL to display [MANUAL].
Tip Every time the DIAL is rotated, the setting switches between [MANUAL] and [PRESET].
3Press the PTT.
Returns the screen to the frequency display screen.
Connecting to registered nodes or rooms
You can register names of nodes and rooms on the Internet and sort them into 5 categories.
Up to a total of 20 nodes and rooms can be registered in each category.
zRegistering category names
1Press and hold the [DISP] key.
2Touch [WIRES-X].
Displays the menu list.
3Touch [3 EDIT CATEGORY TAG].
Displays the category name setting screen.
4Rotate the DIAL to select one of [C1] to [C5], then
press the [DISP] key.
Displays the character input screen.
3 EDIT CATEGORY TAG
C1 ----------------
C2 ----------------
C3 ----------------
C4 ----------------
C5 ----------------
5Enter the category name.
The characters you have just entered appear on the screen.
6Press the [BACK] key.
Returns the screen to the list.
Tip Repeat steps 3 to 6 to set more category names.
7Press the PTT.
Sets the category name and returns the screen to the frequency display screen.

16
zRegistering a node or room
1Touch the node or room you want to connect to.
Displays the menu list of the node (room) you are
connected to.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
JA1YOE-ROOM12345 24
2Touch [ADD].
Displays the category list.
JA1YOE-ROOM12345
NEWS STATION
EMERGENCY
LOCAL NEWS
INT NEWS
3Touch the desired category.
The name of the node or room you are currently
connected to is added to the list of the registered node
and room lists.
C1:TOKYO AREA
C2:FISHING
C3:----------------
C4:----------------
C5:----------------
C1:TOKYO AREA
JA1YOE-ROOM-A
JQ1YBG-ND
JA1YOE-ROOM12345
ADD TO CATEGORY
4Press the [BACK] key.
Returns the screen to the list.
zConnecting to registered nodes or rooms
1Touch [SEARCH & DIRECT].
Displays the category list.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-

17
2Touch one of [C1] to [C5].
Displays the node and room lists.
Tip On room columns, the number of activities (the number of
nodes connected to each room) appears on the right side.
C1:TOKYO AREA
C2:FISHING
C3:----------------
C4:----------------
C5:----------------
3Touch the node or room you want to connect to.
Starts connection.
Tips  •RotatetheDIALtoselectthenodeorroomyouwantto
connect, then press PTT to establish a connection.
JA1YOE-ROOM-A 15
JQ1YBG-ND
JA1YOE-ROOM12345 2
C1:TOKYO AREA
•Ifconnectionissuccessful,themenulistofthenodeor
room you are connected to appears.
•Ifconnectionisunsuccessful,anerrormessageappears
and the screen returns to the list of nodes and rooms.
JA1YOE-ROOM12345
NEWS STATION
EMERGENCY
LOCAL NEWS
INT NEWS
Tip
You can list items in order according to the number of activities or access history from [WIRES-X] →
[2 SEARCH SETUP] in setting mode.
zDisconnecting from the node or room
1Press and hold the [BACK] key.
If disconnection is successful, the screen returns to the local node connection screen.
Releasing the WIRES-X connection
Pressing and holding the [ X ] key for over one second switches the screen to the frequency
display screen, and [
X ] displayed on the left side of the frequency display disappears.
Tip If you did not perform the disconnection operation, the local node and the node or room remain
connected.

18
Connecting to analog nodes
When the node you want to connect to is an analog station, use the DTMF function on
the transceiver. For details on how to use the DTMF function, refer to “DTMF Operation”
in the Advance Manual.
Connecting to nodes or rooms on the Internet
1Set the main band frequency to the local node frequency.
2Touch [MODE] to switch to analog FM mode.
Tip For details, refer to “Selecting the Communication Mode” in the basic operating manual.
3While pressing the PTT, touch [DTMF] displayed on
the screen.
Displays the numeric keypad.
4Touch the DTMF ID key (#) followed by the 5 digits of
the room or node you want to connect with.
5Release the PTT, and keep the transceiver in reception mode for about 10 seconds.
Once connection is established, you will be able to hear audio.
Caution The connection destination screen does not appear.
Tip
You can store DTMF codes consisting of up to 16 digits for 10 channels on the transceiver. If you
register the codes of frequently-used connection destinations in advance, you can easily transmit a
code by pressing its abbreviated number while pressing the PTT.For details, refer to “DTMF Operation”
in the Advance Manual.

19
Communicating with others
1Press the PTT.
The transceiver switches to transmission mode.
2Speak into [MIC].
3Release the PTT.
The transceiver switches to reception mode.
Disconnecting from the node or room
1While pressing the PTT, touch [DTMF] displayed on the screen.
2Press the #99999 (DTMF disconnection command) key.
Disconnects the node or room.
Various display functions
Confirming the location of the local node and the partner station
When the signal from the local node you have connected to contains location information,
you can display the location information on the screen.
Pressing the [DISP] key on any screen of WIRES-X switches the screen to the compass
screen which displays the name of the partner station as well as the direction and distance
to the partner station from your station.
JA1YOE-123
Callsign and distance to
partner station
Progress direction of
own station
Direction of remote station
H-UP: Heading Up
N-UP: North Up
Tip
When “NUMERIC” is selected from [DISPLAY] → [1 TARGET LOCATION] in the setting mode, the
latitude & longitude screen appears instead of the compass screen.
Confirming the frequency
On the WIRES-X screen, press the [V/M] key to change to the frequency display screen
that was displayed before using WIRES-X. Press the [V/M] key again to return to the
WIRES-X screen.
Returning to the initial screen
While on the WIRES-X screen, press and hold the [A/B] key to display the frequency
display screen.
On the frequency display screen, press and hold the [A/B] key to return to the WIRES-X
startup screen (initial screen).

20
Using the News Function of WIRES-X
When using WIRES-X in digital mode, you can transmit/receive messages (text data) and
images; you can also record/play audio messages.
Caution
To using the News function, insert a microSD memory card into the transceiver in advance. For details,
refer to “Using a microSD Memory Card” in the basic operating manual.
Viewing messages
You can read messages (text data) that are transmitted/received by either a local node,
or a node or room on the Internet, from the transceiver.
Viewing text data in local nodes
1Touch the local node.
Displays the menu list of the local node.
SEARCH & DIRECT
JQ1YBG-ND1 Shinagawa-
2Touch the local node name displayed in [LOCAL
NEWS].
If data reception is successful, the menu list of the
local node appears.
JQ1YBG-ND1 Shinagawa
JQ1YBG-ROOM
0202-ROOM
LOCAL NEWS
3Touch [NEWS STATION].
Displays the UPLOAD (transmission)/DOWNLOAD
(reception) select screen.
JQ1YBG-ND1 Shinagaw
NEWS STATION
EMERGENCY
INT NEWS
4Touch [DOWNLOAD].
Displays the data type select screen.
JQ1YBG-ND1 Shinagaw
NEWS STATION
UPLOAD
DOWNLOAD