Yamaha 2013 VMAX User manual

PAPER CRAFT
Thank you for downloading the "VMAX" paper craft model. By simply fol-
lowing this manual while referring to the names and numbers shown on the
parts sheets, you can assemble an authentic-looking replica of the VMAX.
Assembly instructions: Fifteen A4-sized sheets.
Paper craft: Sixteen A4-sized sheets with 174 parts in all
These instructions apply only to the "VMAX".
Other paper craft model instructions can be downloaded separately.
The parts are easier to work with when printed on strong, thick paper.
Assembly Instructions

Note
TO BEGIN
Item of Caution
*Take care when using sharp or pointed objects or when
using bladed cutting tools. Place a heavy sheet of paper
under the paper you want to cut.
*Use glue and other adhesives only in well-ventilated
areas.
*When printing, use a slightly reduced font size as there
are many differences in dimensions depending on the
type of printer used.
Tools and materials needed
-Ruler -Scissors - Blade cutter or "Exacto-knife" - Awl or
other pointed tool (for making a folding crease) - Felt
pen - Pin set - Glue - Hand towel ( for cleaning your
fingers) - Dictionary or other heavy book ( to press the
papers flat)
HOW TO ASSEMBLE
*Follow the working method and markings carefully.
*Cut carefully along the outter line with a cutting blade,
Exacto-knife or scissors.
*Cut carefully with a cutting blade, Exacto-knife or
scissors.
*For folding parts, first use an awl or other pointed
tool to make a light crease along the dotted or solid
line. This will make the folds straight.Avoid making
strong creases, as this will cause the paper to tear.
*As an adhesive, white, wood glue is recommended.
Avoid over application as this will cause the paper
to wrinkle.
*Before beginning assembly, test adhesive amounts
on extra paper.
*Occasionally, white spots will be apparent on folds
andcuts. Usea markeror pencilto fill-inthese spots.
It is recommended that this be done after each stage
of assembly because coloring becomes more diffi-
cult once parts are assembled.
One - point Advice
Basic working method and markings
Fold along these lines. The printed
surface should be on the outside of
the folded shape.
Solid lines
Dotted line
Fold along these lines. The printed
surface should be on the inside of
the folded shape.
Broken lines
Cut out parts marked with an as-
terisk (*).
Cut along these lines
Red dots are the reference positions
for gluing surfaces.
- 2 -
Do not fold or cut the parts
marked .

- 3 -
A-1
Body
Sheet A, 1 part in total Fold each relevant part according to the assembly symbols.
Reference photo
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
1 Assembling the Body

Reference photo
- 4 -
B-3
B-5
B-6
B-4
B-9
B-10
B-13
B-1
B-12
B-7B-14
B-8
B-11 B-2
B-15
B-19
B-18
B-22
B-21
B-17
B-16
B-20
B-24
B-23
Apply glue on the area
indicated in the illustration.
Steering column
Sheet B, 24 parts in total Fold each relevant part according to the assembly symbols.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
2 Assembling the Steering Column
Please use the dots on each component as reference when gluing surfaces.

- 5 -
C-1
C-2
C-2
D-2D-1
Top cover
Sheet C, 2 parts in total Fold each relevant part according to the assembly symbols.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
3 Assembling the Top Cover and Intake
Please use the dots on each component as reference when gluing surfaces.
Reference photo
Fold and glue the parts making sure both tabs (illustrated
by dotted-lines) are neatly tucked in.
Intake
Sheet D, 2 parts in total Fold each relevant part according to the assembly symbols.
Reference photo

- 6 -
E-33 (E-35)
E-36 (E-38)
E-11 (E-9)
E-7 (E-13)
E-40 (E-42)
E-26 (E-25)
E-46 (E-47)
E-5 (E-6)
E-3 (E-4)
E-20 (E-19)
E-15 (E-16)
E-21 (E-22)
E-1 (E-2)
E-37 (E-39)
E-24 (E-27)
E-41 (E-43)
E-12 (E-10)
E-8 (E-14)
E-32 (E-34)
E-29 (E-31)
E-28 (E-30)
E-44 (E-45)
E-17 (E-18)
E-23
Engine
Sheet E, 47 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
4 Assembling the Engine
* Make two of each part.
The diagram shows how the left part of
the engine looks. The numbers within
parentheses indicate parts for the right
part of the engine.
Reference photo
* Only the left part is available.
Left Right

- 7 -
F-1 (F-8)
F-2 (F-9)
F-3 (F-10)
F-4 (F-11)
F-7 (F-14)
F-6 (F-13) F-15 (F-16)
F-17 (F-18)
F-19 (F-20)
F-5 (F-12)
* Make two of each part.
The diagram shows how the left frame
cover looks. The numbers within the
parentheses indicate parts for the right
frame cover.
Reference photo
Left
Right
Side covers
Sheet F, 20 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
5 Assembling the Side Covers

G-14
G-15
G-16
G-17
G-18 G-4
G-20
G-22
G-21
G-19
G-23
G-13
G-12
G-11
G-10
G-9
G-6
G-1
G-2
G-5
G-3
G-7
G-8
- 8 -
- Exhaust A (Right) G-1 to G-4
- Exhaust A (Left) G-5 to G-8
- Exhaust B (Right) G-14 to G-18
- Exhaust B (Left) G-9 to G-13
- Exhaust pipe C G-19 to G-23
Exhaust
Sheet G, 23 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
6 Assembling the Exhaust
in the diagram indicate where parts are to be glued later.
Please do not glue parts at this stage.
When gluing each part, make sure the angle is
correct, referring to the photo below.
To the right side
of the engine.
To the left side of
the engine.
Reference photo
Partition of exhaust pipes
Exhaust A Exhaust B
Exhaust C

- 9 -
H-3
I-3 (I-4)
H-2
H-1
I-5 (I-6)
I-1 (I-2)
I-7 (I-8)
Reference photo
Reference photo
Radiator
Sheet H, 3 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
7 Assembling the Radiator and Rear Suspensions
Rear suspensions
Sheet I, 8 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference
when gluing surfaces.
* Make two of the rear suspensions. They should be
identical. The numbers within the parentheses indicate
the parts for the second suspension.
Apply glue on the area
indicated in the illustration.

- 10 -
J-2
J-1
J-3
K-8K-9
K-5
K-3
K-1
K-2
K-4
K-6
K-7
Reference photo
Seat
Sheet K, 9 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Reference photo
Rear fender
Sheet J, 3 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
8 Assembling the Rear Fender and Seat

- 11 -
L-2
L-4L-13 L-7
L-10
L-11
L-5
L-9
L-8L-6
L-12 L-3
L-1
Front tire
Sheet L, 13 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
9 Assembling the Front Tire
Reference photo

[Rear tire]
- 12 -
M-8
M-2
M-9
M-6
M-11
M-3
M-4
M-12
M-1M-10
M-5
M-18
M-13
M-16 M-1M-19
M-15
M-17
Rear tire
Sheet M, 19 parts in total Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
First, assemble each component by following the
working method and markings. Then, refer to the il-
lustration and photos below to glue the parts together. Indication of
Working Methods
Fold or Curve
Glue
10 Assembling the Rear Tire
Reference photo
*Glue the completed rear arm to the assembled rear tire.
[Rear arm]
To the rear arm.
To the rear tire.

Steering column
Rear suspensions
Top cover
- 13 -

11 Finish
Please use the dots on each component as reference when gluing surfaces.
glue the assembled parts in numerical
order through .
Assembly Instructions
Glue the right and left parts of the engine to the body.
Glue the right and left parts of the intake to the body.
Glue the right and left side covers to the body.
Glue the rear tire to the body.
Glue the rear fender to the right and left frame covers.
Glue the right and left rear suspensions to the rear tire
and the right and left side covers.
Glue exhaust C to the rear tire.
Insert the right and left exhaust B into the engine.
After inserting the right and left exhaust A into the engine,
insert exhaust pipes A and B into exhaust C.
Glue the seat to the body.
Glue the fuel top cover to the body and seat.
Glue the radiator to the body.
Glue the front tire to the steering column.
Glue the part completed in to the body.
Engine (Right)
Intake (Right)
Side cover (Right)
Seat
Side cover (Left)
Rear fender
To the right frame
cover.
Rear tire
Exhaust C
Exhaust B
Exhaust A
Engine (Left)
Intake (Left)
To the Right engine.
Radiator
Front tire
To the Right intake.
Body

- 14 -
RIGHT FRONT
G-1
G-2
G-3
G-4
G-5
G-6
G-7
G-8
G-9
G-10
G-11
G-12
G-13
G-14
G-15
G-16
G-17
G-18
G-19
G-20
G-21
G-22
G-23
L-1
L-2
L-3
L-4
L-5
C-1
C-2
A-1
D-2
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
B-9
B-10
B-11
B-12
B-13
B-14
B-15
B-16
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
E-2
E-4
E-6
E-9
E-10
E-13
E-14
E-16
E-18
E-19
E-22
E-25
E-27
E-30
E-31
E-34
E-35
E-38
E-39
E-42
E-43
E-45
E-47
F-8
F-9
F-10
F-11
F-12
F-13
F-14
F-16
F-18
F-20
I-2
I-4
L-6
L-7
L-8
L-9
L-10
L-11
L-12
L-13
I-6
I-8
12 Assembled Model and the List of Parts
Please refer to the photo below when attaching each component.
Side cover (Right)
Top cover Intake (Right) Engine (Right)
Steering column
Front tire
Exhaust
Body
Rear suspension
(Right)

- 15 -
LEFT REAR
M-1
M-2
M-3
M-4
M-5
M-6
M-7
M-8
M-9
M-10
D-1
M-11
M-12
M-13
M-14
M-15
M-16
M-17
M-18
M-19
F-1
F-2
F-3
F-4
F-5
F-6
F-7
F-15
F-17
E-1
E-3
E-5
E-7
E-8
E-11
E-12
E-15
E-17
E-20
E-21
E-23
E-24
E-26
E-28
E-29
E-32
E-33
E-36
E-37
E-40
E-41
E-44
E-46
F-19
I-1
I-3
I-5
I-7
J-1
J-2
J-3
K-1
K-2
K-3
K-4
K-5
K-6
K-7
K-8
K-9
H-1
H-2
H-3
Intake (Left)
Seat Rear fender
Rear suspension (Left)
Engine (Left)
Radiator
Side cover (Left) Rear tire
12 Assembled Model and the List of Parts
Please refer to the photo below when attaching each component.