Yanmar TVS K-3 User manual

YANMAR TRACTOR (U.S.A.), INC.
TRACTOR HYDRAULIC VALVE STAND KIT
TVS K-3
FOR THE
276 TRACTOR
YANMAR TRACTOR (U.S.A.), INC.

TRACTOR HYDRAULIC VALVE STAND KIT NO. TVS K-3
ITEM
PART NO.
DESCRIPTION QTY.
1 212501 Valve Stand 1
2
212535 Valve Stand Mounting Bracket
1
3 212536
Valve Stand Support Bracket
1
4
212503
Spacer - (Plate)
1
5 006882
Capscrew - 3/8” - 16 x 2-1/2" Lg.
3
008079 Lockwasher 3/8"
3
007451 Hex Nut 3/8" - 16
3
6 542-2112
Capscrew - 1/2" - 13 x 3" Lg. 1
008101 Lockwasher 1/2"
1
007501
Hex Nut 1/2" - 13 1
7
007015
Capscrew - 1/2" - 13 x 1-3/4" Lg. 1
008171 Flatwasher 1/2"
1
008101
Lockwasher 1/2"
1
007501
Hex Nut 1/2" - 13
1
8
26116-120402
Capscrew - 12 mm x 1.75 mm x 40 mm Lg.
2
22117-120000 Lockwasher 12 mm
2
9
26116-080302
Capscrew - 8 mm x 1.25 mm x 30 mm Lg. 2

VALVE STAND KIT INSTALLATION
Using the two existing threaded holes in side of
clutch housing install the Valve Stand Mounting
Bracket using two 12 mm x 1.75 mm x 40 mm
Gaps crews, and 12 mm Lockwashers.
NOTE:
i) Valve Stand Bracket Spacer (Plate) must be
positioned between Valve Stand Mounting
Bracket and clutch housing EXCEPT when
mounted on tractor in combination with a
loader. When tractor is equipped with a
loader discard Spacer Plate as Loader Rear
Mount Mounting Plate is looated between
Valve Stand Bracket and transmission case.
ii) Do not tighten 12 mm capscrews until Valve
Stand Support Bracket is in place.
Remove and discard the two existing 8 mm x
1.25 mm x 16 mm Capscrews used to secure the
instrument panel support to the clutch housing.
Install the Valve Stand Support Bracket using two
8 mm x 1 25 mm x 30 mm Capscrews and 8 mm
Lockwashers (reuse original Lockwashers).
Install the Valve Stand using one 1/2" - 13 x 3"
Capscrew, 1/2" Lockwasher and 1/2" Hex Nut
in the upper mounting hole and one 1/2" - 13 x
1-3/4" Capscrew, 1/2" Flatwasher, 1/2" Lock-
washer and 1/2" Hex Nut in lower hole.
NOTE: The 1/2" - 13 x 1-3/4" Capscrew
secures the Valve Stand and Valve Stand
Support Bracket to the Valve Stand
Mounting Bracket.
Torque mounting hardware as follows:
8 mm Capscrews - 18ft./lbs. (25 Nm, 2.5 Kgm.).
12 mm Capscrews - 59ft./lbs. (80 Nm, 8 Kgm.).
Install the Hydraulic Control Valve on the
Valve Stand as outlined in Assembly Instruc¬
tions, contained in Hydraulic Control Valve
Kit.
NOTE: Use the three 3/8" - 16 x 2-1/2"
Capscrews, 3/8" Lockwashers and
3/8" - 16 Hex Nuts supplied in
Valve Stand Kit to mount Control
Valve to valve stand.
Following Control Valve installation position
the valve stand to place the Control Lever in
desired location for operators convenience and
torque the two 1/2" Capscrews securing Valve
Stand to Valve Stand Mounting Bracket to
55ft./lbs. (75 Nm, 7.5 Kgm.).

_
PRINTED IN U.S.A.