Yeastar Technology Fanvil User manual

Fanvil IP Phone Configuration Guide
Version 1.0
Date: 2016.09.26
Yeastar Information Technology Co. Ltd.

Fanvil IP Phone Configuration Guide
2/8
Introduction
This guide introduces how to configure Fanvil IP phones with Yeastar S-Series VoIP
PBX. You have multiple ways to configure the Fanvil phone:
Registering to Yeastar S-Series Manually
Provisioning Fanvil Phones via PnP (Recommended)
Provisioning Fanvil Phones via DHCP
Supported Phone Models
Fanvil C Series: C01, C58, C58P, C400, C600
Fanvil X3 Series: X3, X3P, X3SP
Fanvil X5 Series: X5,X5G
Note: different IP phone firmware versions may have different web GUI with
different settings.

Fanvil IP Phone Configuration Guide
3/8
Registering to Yeastar S-Series Manually
If you choose registering Fanvil to Yeastar S-Series manually, you have to log in each
phone, and configure one by one.
1. Log in the Fanvil IP phone web user interface.
Username: admin
Password: admin
2. Click “Line” Tab.
Line: choose one line.
User Name: fill in the extension number.
Display Name: set the name you want to appear on other phone’s display
when calling other phones.
Authentication Name: fill in the extension’s “Registration Name”.
Authentication Password: fill in the extension’s “Registration Password”.
Active: Enabled
SIP Proxy Server Address: fill in Yeastar S-Series PBX’s IP address.
SIP Proxy Server Port : fill in Yeastar S-Series PBX’s register port. The

Fanvil IP Phone Configuration Guide
4/8
default port is 5060.
3. Click “Apply”.
4. Check the extensions status. If the extension is registered to Yeastar S-Series
successfully, the “Line Status” will show “Registered”.

Fanvil IP Phone Configuration Guide
5/8
Provisioning Fanvil Phones via PnP
Before provisioning the phones, you must reset the phones to factory defaults in case
that the phones have residual settings of a previous configurations.
1. Connect the phone to the same network with Yeastar S-Series PBX. The phone
will send a PnP request to the PBX when booting up.
2. Log in Yeastar S-Series Web interface, go to “Auto Provisioning” App. Click “Scan”,
all the phones in the local network will show up on the page.
3. Search the phone by MAC address or IP address, and click “edit”.
4. Choose the phone Model, active a line and assign an extension for the phone.
You can also configure keys, features, preferences and codec for the phone.
5. Click “Save”.
6. The system prompts you to reboot the phone, click “OK”.
7. Reboot the phone manually, the phone will restart, then reboot again to apply the
configurations automatically.

Fanvil IP Phone Configuration Guide
6/8
Provisioning Fanvil Phones via DHCP
Before provisioning the phones, you must reset the phones to factory defaults in case
that the phones have residual settings of a previous configurations.
1. Connect the phone to the same network with Yeastar S-Series PBX.
2. Disable local DHCP server in your local network, e.g. disable DHCP server on
Linksys router.
3. Enable DHCP server on Yeastar S-Series and configure the DHCP server settings
according to your local network. (Settings > System > Security > Service)

Fanvil IP Phone Configuration Guide
7/8
4. Go to “Auto Provisioning” App. Click “Scan”, all the phones in the local network will
show up on the page.
5. Search the phone by MAC address or IP address, and click “edit”.
6. Choose the phone Model, active a line and assign an extension for the phone.
You can also configure keys, features, preferences and codec for the phone.

Fanvil IP Phone Configuration Guide
8/8
7. Click “Save”.
8. The system prompts you to reboot the phone, click “OK”.
9. Reboot the phone manually, the phone will restart, then reboot again to apply the
configurations automatically.