Yetter 10000 Magnum Series User manual

10000 SERIES MAGNUM
™
FERTILIZER COULTER
2565-957_Rev_D 02/2018
YETTER MANUFACTRURING CO.
Founded 1930
Colchester, IL 62326-0358
Toll free: 800-447-5777
Fax: [phone]
Website: www.yetterco.com
Email: [email protected]m

FOREWORD
You’ve just joined an exclusive but rapidly growing club.
For our part, we want to welcome you to the group and
thank you for buying a Yetter product.
We hope your new Yetter products will help you achieve
both goals-increase your productivity and increase your
efficiency so that you may generate more profit.
This operator’s manual has been designed into four
major sections: Foreword, Safety Precautions,
Installation Instructions and Parts Breakdown.
This SAFETY ALERT SYMBOL indicates important
safety messages in the manual. When you see
this symbol, be alert to the possibility of
PERSONAL INJURY and carefully read the
message that follows.
The word NOTE is used to convey information that is
out of context with the manual text. It contains special
information such as specifications, techniques and
reference information of a supplementary nature.
The word IMPORTANT is used in the text when
immediate damage will occur to the machine due to
improper technique or operation. Important will apply to
the same information as specified by note only of an
immediate and urgent nature.
It is the responsibility of the user to read the operator’s
manual and comply with the safe and correct operating
procedure and to lubricate and maintain the product
according to the maintenance schedule in the operator’s
manual.
The user is responsible for inspecting his machine and
for having parts repaired or replaced when continued
use of the product would cause damage or excessive
wear to the other parts.
It is the user’s responsibility to deliver his machine to the
Yetter dealer who sold him the product for service or
replacement of defective parts, which are covered by the
warranty policy.
If you are unable to understand or follow the instructions
provided in this publication, consult your local Yetter
dealer or contact:
YETTER MANUFACTURING CO.
309/776-4111
800/447-5777
309/776-3222 (FAX)
Website: www.yetterco.com
E-mail: [e-mail]
WARRANTY
Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being
expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This
warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the Company to
make improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to
be made, other than herein set forth. This warranty is in effect for one year after purchase.
DEALER: ________________________________________
Yetter Manufacturing warrants its own products only and cannot be responsible for damages to equipment on which
mounted.

3
TABLE OF CONTENTS
Foreword ..................................................................................................... 2
Safety........................................................................................................... 4
Torque ......................................................................................................... 5
General Information................................................................................. 6-7
Assembly Instructions ............................................................................ 8-9
Operation.............................................................................................. 10-12
Troubleshooting ....................................................................................... 13
Maintenance......................................................................................... 14-18
Part Identification ................................................................................ 19-44
Photo Album ........................................................................................ 45-47

4
BE ALERT!
YOUR SAFETY IS INVOLVED.
WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS.
IT MEANS “ATTENTION---BECOME ALERT!”
It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using
this machine at the time of initial assignment and at least annually thereafter, of the proper
operation, precautions, and work hazards which exist in the operation of the machine in accordance
with OSHA regulations.
Safety Is No Accident
The following safety instructions, combined with common sense, will save your
equipment from needless damage and the operator from unnecessary exposure to
personal hazard. Pay special attention to the caution notes in the text. Review this
manual at least once each year with new and/or experienced operators.
1. Read and understand the operator’s manual before operating this machine. Failure
to do so is considered a misuse of the equipment.
2. Make sure equipment is secure before operating.
3. Always keep children away from equipment when operating.
4. Make sure everyone that is not directly involved with the operation is out of the
work area before beginning the operation.
5. Make sure all safety devices, shields, and guards are in place and are functional
before beginning the operation.
6. Shut off power to adjust, service, or clean.
7. Keep hands, feet, and clothing away from moving parts. It is a good idea to remove
all jewelry before starting the operation.
8. Visually inspect the machine periodically during operation for signs of excessive
vibration, loose fasteners, and unusual noises.
WARNING: Never work around the toolbar/implement while in a raised position without
using safety lockups.
CAUTION: The 10000 Series Magnum
TM
coulters are very heavy. Pay extra
attention to lifting techniques when handling or maneuvering the coulter
during assembly. Failure to do so may lead to personal injury.

5
BOLT TORQUE
Before operating the 10000 Series Magnum
™
for the first time, check to be sure that all
hardware is tight. Check all hardware again after approximately 50 hours of operation
and at the beginning of each planting season.
All hardware used on the 10000 Series Magnum
™
is Grade 5 unless otherwise
specified. Grade 5 cap screws are marked with three radial lines on the head. If
hardware must be replaced, be sure to replace it with hardware of equal size, strength
and thread type. Refer to the torque table below when tightening hardware.
Important: Over tightening hardware can cause as much damage as when
under tightening. Tightening hardware beyond the recommended range can
reduce its shock load capacity.
The chart below is a guide for proper torque. Use it unless a specified torque is called out
elsewhere in the manual.
Torque is the force you apply to the wrench handle or the cheater bar, times the length of the
handle or bar.
Use a torque wrench whenever possible.
The following table shows torque in ft. lbs. for coarse thread hardware.

6
GENERAL INFORMATION
10000 Series Magnum
TM
Fertilizer Coulter
ORDER from SECTIONS: A, B, and C
Section A:
Model No.
Description
Est. Wt. (lbs)
10000-001-LH LH Magnum, w/ Walking Tandem, fits toolbars 4,5,6,7 wide univ. mount 380
10000-001-RH RH Magnum, w/ Walking Tandem, fits toolbars 4,5,6,7 wide univ. mount 380
10000-002-LH LH Magnum, w/ Walking Tandem, fits toolbars 4” wide, Short mount 375
10000-002-RH RH Magnum, w/ Walking Tandem, fits toolbars 4” wide, Short mount 375
10000-003-LH LH Magnum, w/o Walking Tandem, fits toolbars 4,5,6,7 wide univ. mount 355
10000-003-RH RH Magnum, w/o Walking Tandem, fits toolbars 4,5,6,7 wide univ. mount 355
10000-004-LH LH Magnum, w/o Walking Tandem, fits toolbars 4” wide, Short mount 345
10000-004-LH RH Magnum, w/o Walking Tandem, fits toolbars 4” wide, Short mount 345
Section B:
Model No.
Description
Est. Wt. (lbs)
2987-040-L LH NH3 (3/8”) Tube Kit .395
2987-040-R RH NH3 (3/8”) Tube Kit .395
2987-041-L LH NH3 w/ Liquid (3/8” Dual) Tube Kit .697
2987-041-R RH NH3 w/ Liquid (3/8” Dual) Tube Kit .697
2987-042-L LH NH3 w/ Vapor (3/8” and 3/4”) Tube Kit .954
2987-042-R RH NH3 w/ Vapor (3/8” and 3/4”) Tube Kit .954
2987-043-L LH NH3 w/ Liquid and Vapor (3/8” Dual and 3/4” Single) Tube Kit 1.044
2987-043-R RH NH3 w/ Liquid and Vapor (3/8” Dual and 3/4” Single) Tube Kit 1.044
2987-044-L LH Vapor Only (3/4”) Tube Kit .455
2987-044-R RH Vapor Only (3/4”) Tube Kit .455
2987-046 Liquid (1/2” Single) Tube Kit .425
2987-047 Liquid (1/2” Dual) Tube Kit .850
10000-050-LH LH Magnum Dry Tube Assembly Kit 1.500
10000-050-RH RH Magnum Dry Tube Assembly Kit 1.500
Section C:
Model No.
Description
Est. Wt. (lbs)
10000-011 4” Tall Toolbar Mount Hardware Kit 4
10000-012 5” Tall Toolbar Mount Hardware Kit 4.1
10000-013 6” Tall Toolbar Mount Hardware Kit 4.3
10000-014 7” Tall Toolbar Mount Hardware Kit 4.5
Optional Equipment:
Model No.
Description
Est. Wt. (lbs)
10000-020-LH LH Walking Tandem Wheel Conversion Kit 28.5
10000-020-RH RH Walking Tandem Wheel Conversion Kit 28.5
10000-099 2” Drop Down Kit (For Wheel Tracks) 16.4
STANDARD FEATURES FOR ALL MODELS
•High application speeds with minimal soil disturbance for fall, pre-
plant, and side-dressing applications
•Tube kits for applying liquid, dry, or anhydrous
•All cast design
•Spring loaded knife with carbide tip for extended wear
•22.6” blade set at 4° angle.
•Fits 4x4, 4x6, 5x7, 6x4, and 7x7 toolbar sizes
•Sharktooth® Wheel Closer standard

7
GENERAL INFORMATION
10000 MagnumTM Fertilizer Coulter

8
ASSEMBLY INSTRUCTIONS
WARNING: Never work under the toolbar while in a raised position without
using safety lockups.
WARNING: Use extreme caution, the blade is sharp and may cause bodily
injury. The coulter can be mounted to the toolbar using different techniques.
One way is to mount the main arm assembly to the toolbar and then attach
the components one at a time. Another way is to completely assemble the coulter
before attaching to the toolbar frame.
CAUTION: 10000 Magnum
TM
Fertilizer Coulter and its components are very
heavy. Extra attention to lifting techniques while handling and or maneuvering
the coulter during assembly is very important. Failure to do so may lead to
personal injury or death.
STEP 1: Mark the toolbar frame as to the location that each coulter is to be mounted.
IMPORTANT: Install an equal quantity of right hand and left hand coulters to each
section of the toolbar. Example: A 30’ – 3 section toolbar with 12 coulters (6R & 6L)
will need to install 2R and 2L coulters on each section of the toolbar. If any questions
concerning assembly of coulters, then please contact Yetter Farm Equipment for
recommendations at 800-447-5777.
Note: The coulter blade is in line with the center of the mount bracket. Measure from left
edge to left edge or from right edge to right edge to ensure the coulters are mounted at
the desired spacing.

9
ASSEMBLY INSTRUCTIONS
STEP 2: Attach the 10000 Series Magnum
TM
to the toolbar using the appropriate clamp
and hardware.
HARDWARE KITS
PART IDENTIFICATION

10
OPERATION INSTRUCTIONS
TOOLBAR FRAME HEIGHT ADJUSTMENT
Figure A: The toolbar height is set to 25” above the soil surface. To ensure that frame
heights are correct, it is important measurements are taken before use.
Figure B: The hitch is set too low while the toolbar is not parallel with the soil surface.
Note: The illustrations are intended to show that the settings are critical. Tool frame
levelness and height adjustment are very important settings for correct
performance of the 10000 Magnum
TM
Coulter
Adjusting Opener Depth:
-Raise toolbar frame for shallow
application
-Lower toolbar frame for deeper
application