YitaHome FTPLCG-0271 User manual

ASSEMBLY INSTRUCTIONS
12X14 FT HARDTOP GAZEBO
FTPLCG-0271
FTPLCG-0272
FTPLCG-0273
LHHY-V 1

WARNING
1. Must use ground nails, ropes, and expansions screws for
whichever ground you install on for stability to avoid devastat-
ing injuries for people inside or nearby and property damage
caused by a collapsing gazebo.
2. Do not use this gazebo in high winds, heavy snow, or inclem-
ent weather. It is not designed to withstand strong gusts of wind,
heavy snow accumulation, or other inclement weather. Must
take precautions when the wind speed exceeds 25Mph, and
clear snow when it accumulates more than 2 inches.
3. Before use, thoroughly inspect the gazebo to make sure all
bolts, nuts, and buckles have been completely tightened and
securely fastened.
4. Warranty does not cover damages, losses, or injuries resulting
from improper installation, misuse, not using stability accesso-
ries mentioned above, non snow cleaning, failure to take pre-
cautionary measures, etc.

ASSEMBLY INSTRUCTIONS
1
A
B
B1
X4
X2
X2
CX2
C1 X2
DX4
EX6
FX2
F1 X4
Item no. Reference Image Qty.
1. Two or more people are required for assembly.
2. A ladder and electric drill may be necessary.
3. Do not erect the structure in heavy winds or inclement weather.
4. Do not leave up this unit for extended periods of time, as it is not a
permanent structure or designed to withstand sustained wind or rain.
It is a temporary, portable shelter that shields you from sunlight and rain.
The screens also block flying insects.
5. Do not use candles, matches, or any open flames near the tent.
6. To better align the screws for practical situations, do not fully tighten
screws initially.
7.Professional installation is highly recommended.

ASSEMBLY INSTRUCTIONS
2
F2 X4
GX2
G2 X4
G3 X2
G1 X4
G4 X2
HX4
G6 X2
H1 X4
G5 X2
KX4
LX1
K2 X2
Item no. Reference Image Qty.
K1 X2

MX1
N1 X6
PX4
NX12
JX4
Q1 X4
Q2 X4
QX4
Q3 X4
R1 X4
R2 X4
X2
R3
Q4 X4
Item no. Reference Image Qty.
ASSEMBLY INSTRUCTIONS
3
ST4.8X12mm
M6X15mm
M5X12mm
M6X25mm
1
2
3
4
5
6
7
8
9
M6X16mm
UX120
W3 X6
TX4
X136
X16
X16
X16
X2
X1
X12
10 X12
X1
X1
Item no. Reference Image Qty.
S4 S6
SX4

ASSEMBLY INSTRUCTIONS
4
4pcs
A4pcs
J12pcs
1
1
X4
1
1
1A
A
J
J

When connecting B and B1 via P,C and C1 via P, make sure that 1 holes on part P
(as shown in the picture) should be facing upwards. Do not install it upside down.
ASSEMBLY INSTRUCTIONS
5
2pcs
B2pcs
B1 2pcs
C2pcs
C1 4pcs
P120pcs U
32pcs
1
2
X2
B1
B1
B
B
C
C
C1
C1
1
1
1
P
P
P
P
1
UX7
UX8

ASSEMBLY INSTRUCTIONS
6
316pcs
116pcs 2
B1
B1
C
C
B
B
C1
C1
A
A
A
A
1
2
2
22
A
A

ASSEMBLY INSTRUCTIONS
7
4pcs
H16pcs
1
4pcs
H1
4
H1
H1
H1 H1
H1
H
H
H
H
H
A
1
1
1

ASSEMBLY INSTRUCTIONS
8
4pcs
K2pcs
K1 2pcs K2 16pcs44pcs3
5
K
K
K
K
K
K1
K1
K2
K2
K1
K2
4
4
3
4
3

ASSEMBLY INSTRUCTIONS
9
1pc
L1pc6
6
L
L
6
6
6
1
2

ASSEMBLY INSTRUCTIONS
10
74pcs
D8pcs 1
1
L
L
D
D
D
D
D
D

ASSEMBLY INSTRUCTIONS
11
84pcs
1
1
D
D
D
D
D
A

ASSEMBLY INSTRUCTIONS
12
12pcs
3
6pcs
E6pcs W3
3
W3
E
E
9
X6

ASSEMBLY INSTRUCTIONS
13
10 18pcs
1
E
E
E
D
D
D
D
E
E
E
E
E
E
E
D
D
1
1
L

ASSEMBLY INSTRUCTIONS
14
1pc
M2pcs
51pc 7
11
5
5
7
M
L

15
ASSEMBLY INSTRUCTIONS
10pcs
1
2pcs
G5 2pcs G6 4pcs N
12
G5
G5
G6
G6
G5
N
G6
E
E
E
D
E
E
E
E
D
D
D
D
1

ASSEMBLY INSTRUCTIONS
16
4pcs
R1 4pcs R2 2pcs R3
13
E
D
E
D
R1
R2
R1 R3 R2
R1
R2
R1
R3
R2
Before installing Parts R1/R2/R3,
remove protective films
(with side marks) on both the
front and back sides.
After removal, there will be no
mark and minimal difference
between the sides.
Therefore, pay close attention
to directions before removal.

ASSEMBLY INSTRUCTIONS
17
2pcs
G3 2pcs G4 4pcs N10pcs
1
N
G3
G3
G3
G4
G4
G4
G4
1
14
E
D
1

ASSEMBLY INSTRUCTIONS
18
2pcs
F4pcs F1 4pcs F2 4pcs
Q2
4pcs
Q1
2pcs
Q
15
F1
Q1
Q1
Q1
Q
Q
Q2
Q2
Q2
Q2
Q1
Q1
Q1
Q1
F1
F1
F1
Q2
Q2
Q1
QQ1
F1
F1
F1
F
F
F2
F2
F2
F2
E
E
E
D
D
Before installing Parts Q/Q1/Q2,
remove protective films
(with side marks) on both the
front and back sides.
After removal, there will be no
mark and minimal difference
between the sides.
Therefore, pay close attention
to directions before removal.