YOKOGAWA DPharp EJX510B User manual

User’s
Manual
Yokogawa Electric Corporation
EJX510B and EJX530B
Absolute and Gauge Pressure
Transmitters
IM 01C27F01-01EN
IM 01C27F01-01EN
11th Edition

Toc-1
IM 01C27F01-01EN
EJX510B and EJX530B
Absolute and Gauge Pressure Transmitters
IM 01C27F01-01EN 11th Edition
11th Edition: Dec. 2018 (YK)
All Rights Reserved, Copyright © 2010, Yokogawa Electric Corporation
Contents
1. Introduction............................................................................................... 1-1
1.1 Safe Use of This Product ................................................................................. 1-2
1.2 Radio Wave........................................................................................................ 1-3
1.3 Warranty............................................................................................................. 1-4
1.4 Trademarks........................................................................................................ 1-4
1.5 Control of Pollution Caused by the Product.................................................. 1-5
2. Handling Cautions.................................................................................... 2-1
2.1 ModelandSpecicationsCheck..................................................................... 2-1
2.2 Unpacking.......................................................................................................... 2-1
2.3 Storage............................................................................................................... 2-2
2.4 Selecting the Installation Location ................................................................ 2-2
2.5 Pressure Connection........................................................................................ 2-3
2.6 Restrictions on Use of Radio Transceivers ................................................... 2-3
2.7 Insulation Resistance and Dielectric Strength Test...................................... 2-3
2.8 Installation of an Explosion-Protected Instrument ....................................... 2-4
2.8.1 FM Approval....................................................................................... 2-5
2.8.2 CSACertication................................................................................ 2-6
2.8.3 ATEXCertication.............................................................................. 2-6
2.8.4 IECExCertication............................................................................. 2-8
2.9 EMC Conformity Standards............................................................................. 2-8
2.10 Pressure Equipment Directive (PED) .................................................. 2-9
2.11 Low Voltage Directive....................................................................................... 2-9
2.12 Regulatory Compliance for Radio and Telecommunication...................... 2-10
2.12.1 Radio Equipment Directive (RE)...................................................... 2-10
2.12.2 FCC compliance .............................................................................. 2-10
2.12.3 Industry Canada (IC) compliance .................................................... 2-10
2.13 RoHS................................................................................................................. 2-11
3. Component Names .................................................................................. 3-1
4. Installation................................................................................................. 4-1
4.1 Precautions ....................................................................................................... 4-1
4.2 Mounting ............................................................................................................ 4-1
4.3 Rotating Transmitter Section........................................................................... 4-2

Toc-2
IM 01C27F01-01EN
4.4 Changing the Direction of Integral Indicator ................................................. 4-2
4.5 Changing the direction of the antenna........................................................... 4-3
5. Installing Impulse Piping......................................................................... 5-1
5.1 Impulse Piping Installation Precautions ........................................................ 5-1
5.1.1 Connecting Impulse Piping to a Transmitter...................................... 5-1
5.1.2 Routing the Impulse Piping................................................................ 5-1
5.2 Impulse Piping Connection Examples ........................................................... 5-2
6. Wiring......................................................................................................... 6-1
6.1 Mounting Antenna and Wiring......................................................................... 6-1
6.1.1 Mounting the antenna ........................................................................ 6-1
6.1.2 Mounting External Antenna and Wiring Antenna Extension Cable ... 6-2
6.1.2.1 Mounting of External Antenna............................................................ 6-2
6.1.2.2 Wiring of Antenna Extension Cable ................................................... 6-2
6.1.2.3 Mounting of Surge Protective Device and Wiring.............................. 6-4
6.2 Grounding.......................................................................................................... 6-4
6.3 Power Supply Wiring Precautions.................................................................. 6-5
6.4 Selecting the Wiring Materials......................................................................... 6-5
6.5 Connection of the External Power Source Terminal..................................... 6-5
7. Operation................................................................................................... 7-1
7.1 Preparation for Starting Operation ................................................................. 7-1
7.2 Zero Point Adjustment ..................................................................................... 7-2
7.3 Starting Operation ............................................................................................ 7-3
7.4 Connecting to the Field Wireless Network..................................................... 7-3
7.5 Shutting Down the Transmitter ....................................................................... 7-5
8. Setting Parameters................................................................................... 8-1
8.1 Environment for parameter setting................................................................. 8-1
8.2 Preparing Software........................................................................................... 8-1
8.2.1 SoftwaresfortheFieldWirelessCongurationToolandtheDevice
CongurationTool .............................................................................. 8-1
8.2.2 Software Download............................................................................ 8-1
8.3 Setting Parameters ........................................................................................... 8-1
8.3.1 Parameter Usage and Selection........................................................ 8-1
8.3.2 Function Block and Menu Tree .......................................................... 8-2
8.3.3 Parameters for Wireless Communication........................................ 8-10
8.3.4 Tag and Device Information ............................................................. 8-10
8.3.5 Unit................................................................................................... 8-11
8.3.6 Range Change................................................................................. 8-11
8.3.7 Output Signal Low Cut Mode Setup ................................................ 8-11
8.3.8 Integral Indicator Scale Setup.......................................................... 8-12
8.3.9 Unit for Displayed Temperature ....................................................... 8-12
8.3.10 Zero Point Adjustment and Span Adjustment.................................. 8-12

Toc-3
IM 01C27F01-01EN
8.3.11 Software Write Protect..................................................................... 8-14
8.3.12 Switching to Deep Sleep Mode........................................................ 8-15
8.3.13 Switching to Silence Mode............................................................... 8-15
8.4 Self-Diagnostics.............................................................................................. 8-16
8.4.1 IdentifyProblemsbyUsingtheDeviceCongurationTool.............. 8-16
8.4.2 Alert Report ...................................................................................... 8-17
8.4.3 Checking with Integral Indicator....................................................... 8-19
9. Maintenance.............................................................................................. 9-1
9.1 Overview ............................................................................................................ 9-1
9.2 Calibration Instruments Selection .................................................................. 9-1
9.3 Calibration ......................................................................................................... 9-1
9.4 Disassembly and Reassembly ........................................................................ 9-4
9.4.1 Replacing the Integral Indicator ......................................................... 9-5
9.4.2 Replacing the RF Assembly............................................................... 9-5
9.4.3 Replacing the CPU Assembly............................................................ 9-6
9.4.4 Cleaning and Replacing the Capsule Assembly ............................... 9-6
9.4.5 Replacing the Battery Pack ............................................................... 9-7
9.4.6 Replacing the Batteries...................................................................... 9-8
9.4.7 Handling Batteries.............................................................................. 9-8
9.4.8 Replacing the Power Supply Module................................................. 9-9
9.5 Troubleshooting................................................................................................ 9-9
9.5.1 Basic Troubleshooting ....................................................................... 9-9
9.5.2 Troubleshooting Flowcharts............................................................. 9-10
9.5.3 Errors and Countermeasures .......................................................... 9-12
10. Parameter Summary .............................................................................. 10-1
11. GeneralSpecications .......................................................................... 11-1
11.1 StandardSpecications................................................................................. 11-1
11.2 ModelandSufxCodes ................................................................................. 11-3
11.3 OptionalSpecications.................................................................................. 11-4
11.4 Dimensions...................................................................................................... 11-5
Revision Information

<1. Introduction> 1-1
IM 01C27F01-01EN
1. Introduction
Thank you for purchasing the DPharp EJX
Pressure transmitter.
Your EJX Pressure Transmitter was precisely
calibrated at the factory before shipment. To ensure
bothsafetyandefciency,pleasereadthismanual
carefully before you operate the instrument.
NOTE
This manual covers the EJX510B absolute
pressure transmitter and EJX530B gauge
pressure transmitter, and describes how to use
for the detachable antenna type transmitters
(Amplierhousingcode8or9).
Unless otherwise stated, the illustrations in this
manual are of the EJX530B gauge pressure
transmitter with a detachable antenna type.
Usersoftheothermodelsandspecications
should bear in mind that certain features of their
instrument will differ from those shown in the
illustrations of the EJX530B.
MODEL SUFFIX
EJX510B --8*
--9*
EJX530B
Regarding This Manual
• This manual should be provided to the end
user.
• Thismanualandtheidenticationtagattached
on packing box are essential parts of the
product; keep them in a safe place for future
reference.
• The contents of this manual are subject to
change without prior notice.
• All rights reserved. No part of this manual may
be reproduced in any form without Yokogawa’s
written permission.
• Yokogawa makes no warranty of any kind with
regard to this manual, including, but not limited
to, implied warranty of merchantability and
tnessforaparticularpurpose.
• If any question arises or errors are found, or if
any information is missing from this manual,
please inform the nearest Yokogawa sales
ofce.
• Thespecicationscoveredbythismanualare
limited to those for the standard type under the
speciedmodelnumberbreak-downanddo
not cover custom-made instruments. When
productswhosesufxcodeoroptionalcodes
contain code “Z” and an exclusive document is
attached, please read it along with this manual.
• Pleasenotethatchangesinthespecications,
construction, or component parts of the
instrumentmaynotimmediatelybereected
in this manual at the time of change, provided
that postponement of revisions will not cause
difcultytotheuserfromafunctionalor
performance standpoint.
• Yokogawa assumes no responsibilities for this
product except as stated in the warranty.
• If the customer or any third party is harmed by
the use of this product, Yokogawa assumes
no responsibility for any such harm owing to
any defects in the product which were not
predictable, or for any indirect damages.
• The following safety symbols are used in this
manual and on the product:
WARNING
Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious
injury.
CAUTION
Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate
injury or physical damage. It may also be used to
alert against unsafe practices.
IMPORTANT
Indicates that operating the hardware or software
in this manner may damage it or lead to system
failure.

<1. Introduction>1-2
IM 01C27F01-01EN
NOTE
Draws attention to information essential for
understanding the operation and features.
Functional grounding terminal
Caution
This symbol indicates that the operator
must refer to an explanation in the user’s
manual in order to avoid the risk of injury
or death of personnel or damage to the
instrument.
Notice
NO RIGHTS OR LICENSES, EXPRESS OR
IMPLIED, ARE GRANTED TO USE THIRD-PARTY
DEVICES IN COMBINATION WITH THESE
PRODUCTS IN A WIRELESS MESH NETWORK,
OR TO USE THIRD-PARTY SERVICES TO
ACCESS, MONITOR OR CONTROL THESE
PRODUCTS IN A WIRELESS MESH NEWORK
VIA THE INTERNET OR ANOTHER EXTERNAL
WIDE AREA NETWORK.
Patent Marking
Covered by one or more claims of patents:
http://sipcollc.com/patent-list/ and
http://intusiq.com/patent-list/.
1.1 Safe Use of This Product
This product is designed to be used by a person
with specialized knowledge. For the safety of the
operator and to protect the instrument and the
system, please be sure to follow this manual’s
safety instructions when handling this instrument.
If these instructions are not heeded, the protection
provided by this instrument may be impaired. In
this case, Yokogawa cannot guarantee that the
instrument can be safely operated. Please pay
special attention to the following points:
(a) Installation
• This instrument may only be installed by an
engineer or technician who has an expert
knowledge of this device. Operators are not
allowed to carry out installation unless they
meet this condition.
• With high process temperatures, care must
be taken not to burn yourself by touching the
instrument or its casing.
• Never loosen the process connector nuts when
the instrument is installed in a process. This can
lead to a sudden, explosive release of process
uids.
• When draining condensate from the pressure
detector section, take appropriate precautions
to prevent the inhalation of harmful vapors and
thecontactoftoxicprocessuidswiththeskin
or eyes.
• When removing the instrument from a
hazardousprocess,avoidcontactwiththeuid
and the interior of the meter.
• All installation shall comply with local installation
requirements and the local electrical code.
(b) Wiring
• The instrument must be installed by an
engineer or technician who has an expert
knowledge of this instrument. Operators are not
permitted to carry out wiring unless they meet
this condition.

<1. Introduction> 1-3
IM 01C27F01-01EN
(c) Maintenance
• Please carry out only the maintenance
procedures described in this manual. If you
require further assistance, please contact the
nearestYokogawaofce.
• Care should be taken to prevent the build up of
dust or other materials on the display glass and
the name plate. To clean these surfaces, use a
soft, dry cloth.
(d) Explosion Protected Type Instrument
• Users of explosion proof instruments should
referrsttoSection2.8(Installationofan
Explosion-Protected Instrument) of this manual.
• The use of this instrument is restricted to those
who have received appropriate training in the
device.
• Take care not to create sparks when accessing
the instrument or peripheral devices in a
hazardous location.
• Repairormodicationtothisinstrumentby
customer will cause malfunction of explosion
protect function and hazardous situation. If you
needtorepairormodication,pleasecontact
thenearestYokogawaofce.
(e) Modication
• Yokogawa will not be liable for malfunctions or
damageresultingfromanymodicationmade
to this instrument by the customer.
(f) Product Disposal
• The instrument should be disposed of in
accordance with local and national legislation/
regulations.
(g) Authorized Representative in EEA
• In relation to the CE Marking, The authorized
representative for this product in the EEA
(European Economic Area) is:
Yokogawa Europe B.V.
Euroweg 2, 3825 HD Amersfoort,
The Netherlands
1.2 Radio Wave
IMPORTANT
- This instrument is equipped with a wireless
modulewhichisdesignatedasacertication
of construction type as a wireless
facility for 2.4 GHz band low-power data
communication system of the Radio Act.
Refer to 2.12 “Regulatory Compliance for
Radio and Telecommunication” for detail.
- Duetothedesignatedcerticationof
construction type, users may be subject to
legal punishment in case of:
- Disassembling or modifying the wireless
module or antenna in this instrument
- Peelingoffthecerticationlabelattached
to the wireless module in this instrument
- Preventing interference with other wireless
stations
The operating frequency bandwidth of this
instrument may overlap the same range
asindustrialdevices,scienticdevices,
medical devices, microwave ovens, licensed
premises radio stations and non-licensed
speciedlow-powerradiostationsformobile
objectidenticationsystemsusedinfactory
production lines.
Before using this instrument, ensure that
neitherapremisesradiostationnorspecied
low power radio station for mobile object
identicationsystemsisinusenearby.
If this instrument causes radio wave
interference to a wireless station for mobile
objectidenticationsystems,promptly
change the frequency being used or turn
off the source of radio wave emissions.
Then,contactaYokogawaofceregarding
countermeasures to prevent interference,
such as setting up partitions.

<1. Introduction>1-4
IM 01C27F01-01EN
1.3 Warranty
• The warranty shall cover the period noted on
the quotation presented to the purchaser at the
time of purchase. Problems occurring during
the warranty period shall basically be repaired
free of charge.
• If any problems are experienced with this
instrument, the customer should contact the
Yokogawa representative from which this
instrument was purchased or the nearest
Yokogawaofce.
• If a problem arises with this instrument,
please inform us of the nature of the problem
and the circumstances under which it
developed,includingthemodelspecication
and serial number. Any diagrams, data and
other information you can include in your
communication will also be helpful.
• Thepartyresponsibleforthecostofxingthe
problem shall be determined by Yokogawa
following an investigation conducted by
Yokogawa.
• The purchaser shall bear the responsibility for
repair costs, even during the warranty period, if
the malfunction is due to:
- Improper and/or inadequate maintenance by
the purchaser.
- Malfunction or damage due to a failure
to handle, use, or store the instrument in
accordancewiththedesignspecications.
- Use of the product in question in a location
notconformingtothestandardsspeciedby
Yokogawa, or due to improper maintenance
of the installation location.
- Failureordamageduetomodicationor
repair by any party except Yokogawa or an
approved representative of Yokogawa.
- Malfunction or damage from improper
relocation of the product in question after
delivery.
- Reasonofforcemajeuresuchasres,
earthquakes,storms/oods,thunder/
lightening, or other natural disasters, or
disturbances, riots, warfare, or radioactive
contamination.
1.4 Trademarks
In this document, trademarks or registered
trademarks are not marked with “™” or “®”.
Product names and company names in this
document are trademarks or registered trademarks
of the respective companies.

<1. Introduction> 1-5
IM 01C27F01-01EN
1.5 Control of Pollution Caused by the Product
This is an explanation for the product based on “Control of Pollution caused by Electronic Information
Products” in the People’s Republic of China.
電子情報製品汚染制御管理弁法（中国版RoHS）
产品中有害物质或元素的名称及含量
产品中有害物质或元素的名称及含量
型号 部件名称
有害物质
铅
（Pb） 汞 （Hg） 镉 （Cd） 六价铬 （Cr(VI)） 多溴联苯 （PBB） 多溴二苯醚 （PBDE）
EJX-B series
无线差压 / 压力
变送器
YTA510
无线温度变送器
壳体 ×○○○○○
膜盒组件 ×○○○○○
基板组件 ×○○×○○
电源连接线 ×○○○○○
天线组件 ×○○○○○
电池组件 ×○○○○○
○ ：表示该部件的所有均质材料中的有害物质的含量均在 GB/T26572 标准中所规定的限量以下。
× ：表示至少该部件的某些均质材料中的有害物质的含量均在 GB/T26572 标准中所规定的限量以上。
环保使用期限 ：
该标识适用于 SJ /T11364 中所述，在中华人民共和国销售的电子电气产品的环保使用期限。
注）该年数为“环保使用期限”，并非产品的质量保证期。

<2. Handling Cautions> 2-1
IM 01C27F01-01EN
2. Handling Cautions
This chapter provides important information on how
to handle the transmitter. Read this carefully before
using the transmitter.
EJX Series transmitters are thoroughly tested at the
factory before shipment. When taking delivery of an
instrument, visually check them to make sure that
no damage occurred during shipment.
Also check that all transmitter mounting hardware
showningure2.1isincluded.Ifthetransmitter
is ordered without the mounting bracket and the
process connector, the transmitter mounting
hardware will not be included. After checking the
transmitter, carefully repack it in its box and keep it
there until you are ready to install it.
U-bolt Nut (L type)
Mounting bracket
U-bolt (L type)
U-bolt (S type)
U-bolt Nut
(S type)
F0201.ai
No antenna is provided for Amplifier
housing code 9.
Antenna
Figure 2.1 Transmitter Mounting Hardware
2.1 ModelandSpecications
Check
Themodelnameandspecicationsarewrittenon
the name plate attached to the case.
: Refer to USER'S MANUAL.
Made in Japan
TOKYO 180-8750 JAPAN
MODEL
SUFFIX
SUPPLY
OUTPUT
MWP
mA DC
V DC
STYLE
CAL
RNG
NO.
F0202.ai
Figure 2.2 Name Plate
• QR Code
TheproducthasaQRCodepastedforefcient
plant maintenance work and asset information
management.
Itenablesconrmingthespecicationsof
purchased products and user’s manuals.
For more details, please refer to the following
URL.
https://www.yokogawa.com/qr-code
QR Code is a registered trademark of DENSO
WAVE INCORPORATED.
2.2 Unpacking
Keep the transmitter in its original packaging to
prevent it from being damaged during shipment.
Do not unpack the transmitter until it reaches the
installation site.