YOKOGAWA YTMX580 User guide

Technical
Information
YTMX580 Multi-Input Temperature
Transmitter Startup Guide
(From Device Conguration and Wireless Network
Connection to Process Data Monitoring)
TI 04R01B01-01EN
TI 04R01B01-01EN
©Copyright Oct. 2011 (KP)
1st Edition, Dec. 12, 2011 (KP)
Contents
Introduction......................................................................................................2
Precautions for Use......................................................................................... 2
1. Overview.................................................................................................. 3
1.1 Device Conguration ........................................................................................3
1.2 Hardware and Software Requirements...........................................................4
1.3 Conguration Work Flow .................................................................................5
2. Preparation.............................................................................................. 6
2.1 Designing the Network .....................................................................................6
2.2 Installing the Software and Device File...........................................................6
2.3 Conguring the PC Network ............................................................................6
2.4 Conguring the Monitoring Device Network .................................................7
2.4.1 Conguring the DX...........................................................................................7
2.4.2 Conguring the MW.........................................................................................8
2.5 Connecting the Devices ...................................................................................8
3. Conguration .......................................................................................... 9
3.1 Provisioning (Step 1) ........................................................................................9
3.2 Setting the YTMX (Step 2)...............................................................................12
3.3 Conguring the Network (Communication) and
Registering the Device (Step 3) .....................................................................15
3.3.1 Conguring Network (Communication) ..................................................... 15
3.3.2 Registering the Device (YTMX).................................................................... 17
3.4 Conguring the Monitoring Device (Step 4).................................................23
3.4.1 Conguring the DX........................................................................................ 23
3.4.2 Conguring the MW100................................................................................ 28
4. Checking the Display of Process Data...............................................33
Appendix 1 Modbus Registers.................................................................... 34
Appendix 2 Explanation of Terms...............................................................35
Appendix 3 DX Custom Display Example..................................................36
Revision Information.....................................................................................37
Yokogawa Electric Corporation
2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 Japan
Tel.: [phone] Fax.: [phone]
[Style : S1]

2
TI 04R01B01-01EN Dec. 12, 2011-00
Introduction
This document describes the conguration of the main devices– including the range settings of the YTMX580
Multi-Point Temperature Transmitter, the connection to the eld wireless network, and an example of displaying
the process data (PV values) on the DX2000 Paperless Recorder or the MW100 Data Acquisition Unit.
n Notes
• The content of this document is subject to change without notice as a result of enhanced performance and func-
tions.
• If you nd any inaccuracies or errors in this document, please contact Yokogawa.
• Any copy or reproduction of the content of this document, in whole or in part, without permission is prohibited.
n Trademarks
• The Yokogawa product and brand names appearing in this document are trademarks or registered trademarks
of Yokogawa Electric Corporation.
• The company trademarks and registered trademarks appearing in this document are not marked with TM or ®.
• All product names appearing in this document are trademarks or registered trademarks of their respective com-
panies.
Precautions for Use
n Scope of Explanation in this Document
• This document does not explain the basic operations of operating systems such as Windows XP. For the basic
operations of the respective operating system, please read the User’s Guide or other documentation of the
respective operating system.
• This document does not explain the basic settings and operations of software, including the conguration tools,
and the hardware and software used. For details on the software or the hardware and software used, please
read the instruction manuals of the respective software or the hardware and software used.
n Disclaimer for this Document
• Yokogawa does not provide any guarantees regarding the details on the conguration explained in this docu-
ment.
• Yokogawa does not assume any responsibility for any damage directly or indirectly su󰀨ered by the user or any
third party related to the use of the details on the conguration explained in this document.
All Rights Reserved. Copyright © 2011, Yokogawa Electric Corporation

3
TI 04R01B01-01EN Dec. 12, 2011-00
1. Overview
One YTMX580 Multi-Input Temperature Transmitter (hereinafter referred to as YTMX) and one YFGW710 Field
Wireless Integrated Gateway (hereinafter referred to as YFGW) are connected via the eld wireless network, and
the process data measured by the YTMX is transmitted to the YFGW at Period of 2 seconds.
The process data is acquired via Modbus/TCP and displayed*1 by the DX2000 Paperless Recorder (hereinafter
referred to as DX) or the MW100 Data Acquisition Unit (hereinafter referred to as MW) that is connected to the
YFGW via Ethernet.
To congure the YTMX and the eld wireless network, two personal computers (hereinafter referred to as PCs)
are used.
In one PC (hereinafter referred to as PC1), Field Wireless Congurator that is used for eld wireless network
conguration and maintenance and Field Wireless Management Tool that is used for eld wireless network and
wireless eld device management and operation status monitoring are installed.
In the other PC (hereinafter referred to as PC2), FieldMate Versatile Device Management Wizard (hereinafter
referred to as FieldMate) that is used to congure and provision the VTMX, and FieldMate Provisioning Device
Tool that runs in conjunction with FieldMate are installed.
Note that the YFGW network is congured as a star topology and wireless eld devices are used as IO devices.
*1: For the MW, the data is monitored on the PC.
1.1 Device Conguration
Figure 1 shows the device conguration.
■For provisioning
or
Figure 1 Device Conguration

4
TI 04R01B01-01EN Dec. 12, 2011-00
1.2 Hardware and Software Requirements
Table 1 shows the hardware and software requirements, including products recommended by Yokogawa.
This document describes an example of using the hardware and software listed below.
Table 1 Hardware and Software Requirements, including Products Recommended by Yokogawa
Category Hardware and Software Quantity Remarks
Hardware YTMX580 Multi-Input Temperature Transmitter 1
YFGW710 Field Wireless Integrated Gateway 1
DX2000 or MW100 1The MATH option is required.
Personal computers
• PC1
• PC2
2PC1: For eld wireless network congura-
tion and maintenance, and eld wireless
network and wireless eld device manage-
ment
PC2: For device conguration and provi-
sioning
Infrared adapter
Supplier: ACTiSYS
Product name: Infrared USB Serial Adapter
Product No.: ACT-IR224UN-LN96 (9,600 bps)
1
Hub 13 ports or more
LAN cable 3Straight cable
Software FieldMate Versatile Device Management Wizard
(R2.03.01 or later)
• FieldMate Provisioning Device Tool (for provi-
sioning)
1Wireless eld device conguration tool
Field Wireless Congurator (R1.02.00 or later)
Field Wireless Management Tool (R1.02.00 or
later)
1
1
Field wireless system conguration tool
Included with the YFGW
MW100 Viewer Software (R3.03.01 or later recom-
mended*1)
• MW100 IP Conguration Software (for network
conguration)
1Included with the MW100
Device File Device File (R3.02.12 or later)*2 1 set
*1: You can use the software included with the MW used or a compatible revision of software.
*2: An update patch le for Device File R3.02.12 can be downloaded from the website.
<http://eld-wireless.com/>

5
TI 04R01B01-01EN Dec. 12, 2011-00
1.3 Conguration Work Flow
Figure 2 shows the conguration work ow. This document explains the operating procedures according to the
steps shown in the work ow. For the work items and conguration tools used for the respective work items, refer
to Table 2 “Work Items and Conguration Tools.”
Step 1
Step 2
Step 3
Step 4
Start
operation
Provisioning (Section 3.1)
・ Perform a provisioning task to enable the YTMX to join the field wireless network.
Configuration tool used: FieldMate Provisioning Device Tool
Configuring the YTMX*1 (Section 3.2)
・ Configure the device (the YTMX) to measure temperatures.
Configuration tool used: FieldMate
Configuring the Network (Communication) and Registering Device*2 (Section 3.3)
・ Configure the network (communication), register the device (the YTMX) with the YFGW
and connect the YTMX to the field wireless network.
Configuration tool used: Field Wireless Configurator
Configuring Monitoring Device (Section 3.4)
・ Configure the DX or the MW to acquire the process data via Modbus/TCP.
Figure 2 Work Flow
Table 2 Work Items and Conguration Tools
Item Settings Conguration Tool Applicable Device and
Communication Medium
Provisioning • Device Tag
• Network ID
• Join Key
• Export Conguration File
FieldMate Provisioning
Device Tool
Congure the settings on
the YTMX via infrared com-
munication
Conguring the YTMX • Device Conguration
• Input Conguration
FieldMate Congure the settings
on the YTMX via infrared
communication or wireless
communication*1
Conguring the Network
(Communication) and Reg-
istering Device
• Import Conguration File
• Publication Period
• Device Role
• Register Device (YTMX)
• Modbus Conguration
Field Wireless Congurator Congure the settings on
the YFGW via Ethernet
*1: Conguration via wireless communication is available after operation starts.
*2: Conguration on the YTMX is performed from the YFGW.

6
TI 04R01B01-01EN Dec. 12, 2011-00
2. Preparation
2.1 Designing the Network
To congure the eld wireless network, rst determine the network ID, the device tag name of the wireless eld
device (YTMX), and the network information for the Ethernet connection of the YFGW.
This document uses the settings shown in Table 3 to congure the network.
Table 3 Network Settings
Item Settings
Network ID 100
Device Tag (name to identify the device) YTMX580
Network Settings Device IP Address Subnet Mask Default Gateway
YFGW 192.168.0.101
255.255.255.0 192.168.0.1PC1 192.168.0.102
DX or MW100 192.168.0.200
Network Topology Star
2.2 Installing the Software and Device File
Table 4 shows the software that is required for conguration.
Install the conguration tools, the infrared adapter driver, and Device File on each of the PCs.
For the installation procedure, refer to the instruction manual of the respective software.
Table 4 PC and Software
PC Software
PC1 • Field Wireless Congurator (included with the YFGW)
• Field Wireless Management Tool (included with the YFGW)
• Device File (CF/DD) R3.02.12 or later*1
• MW100 Viewer Software (included with the MW100)
PC2 • FieldMate Versatile Device Management Wizard
• Infrared adapter driver
*1: An update patch le for Device File R3.02.12 can be downloaded from the website.
<http://eld-wireless.com/>
2.3 Conguring the PC Network
Congure the network settings shown in Table 3 on PC1.
For the network conguration procedures, refer to the instruction manual of the PC.

7
TI 04R01B01-01EN Dec. 12, 2011-00
2.4 Conguring the Monitoring Device Network
The following shows the network settings to connect the DX or the MW to the YFGW via Ethernet.
For the operating procedures, refer to the instruction manuals of the respective devices.
Settings
IP Address: 192.168.0.200
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
2.4.1 Conguring the DX
Congure the network settings in the Basic Setting Mode.
Perform the following operation to enter the Basic Setting Mode.
MENU key (to switch to setting mode) > [Menu] tab > [Basic Setting mode] > DISP/ENTER
When the dialog box to conrm whether to enter the Basic Setting mode appears, Select [Yes] > DISP/ENTER.
Setup Screen
MENU key (to switch to setting mode) > [Menu] tab > [Basic Setting mode] > [Communication (Ethernet)] >
[IP-address, Host settings] > DISP/ENTER

8
TI 04R01B01-01EN Dec. 12, 2011-00
When the all the settings have been congured, click [End] to exit the basic setting mode.
The dialog box appears. Select [Yes]. Press DISP/ENTER
2.4.2 Conguring the MW
Congure the network settings in MW100 IP Conguration Software.
1. Start MW100 IP Conguration Software from the Start menu of PC1.
2. Click [Search]. Select the detected MW and click [Network Conguration]. Congure the network settings and
click [Apply].
2.5 Connecting the Devices
Connect the individual devices according to the device conguration shown in Figure 1.

9
TI 04R01B01-01EN Dec. 12, 2011-00
3. Conguration
3.1 Provisioning (Step 1)
<Important>
Provisioning information is required to connect the YTMX to the gateway. Be sure to export the provisioning infor-
mation, because the information will need to be imported into Field Wireless Congurator later on.
1. Connect the infrared adapter to PC2 and ensure that the distance to the infrared communication port on the
front of the YTMX is within 30 cm.
within 30 cm
2. Start Provisioning Device Tool from the Start menu.
3. Select [Ir Adapter Conguration] from the Tools menu and click [OK]. Select the Com port for the infrared
adapter and click [OK].

10
TI 04R01B01-01EN Dec. 12, 2011-00
4. Click [Get Device Information].
When the information acquisition is complete, the acquired information and the dialog box to notify you that
information acquisition is complete appear. Click [OK].
5. Set [100] in Network ID and [YTMX580] in Device Tag, and click [Start Provisioning]. If a device tag is already
set, set [YTMX580] as necessary. When the dialog box to conrm whether to update the settings appears, click
[OK]. When the completion dialog box appears, click [OK].
6. Click [Export Provisioning Data]. Enter “YTMX-Prov” in File Name and click [Save]. (Default:
“c:¥FM¥Export¥PD”) When the dialog box to notify you that the export is complete appears, click [Ok].

11
TI 04R01B01-01EN Dec. 12, 2011-00
7. Click [Exit] from the File menu to exit Provisioning Device Tool.

12
TI 04R01B01-01EN Dec. 12, 2011-00
3.2 Setting the YTMX (Step 2)
This section describes the device settings of the YTMX. The screen shows FieldMate R2.03.01 as an example.
For details on FieldMate, refer to the instruction manual of FieldMate.
1. Connect the infrared adapter to PC2 and ensure that the distance to the infrared communication port on the
front of the YTMX is within 30 cm.
2. Start FieldMate from the Start menu.
When the Login window appears, select [ISA100 (Infrared)] from [Default Scan Segment] and click [OK].
3. When the icon for the detected YTMX is displayed in Segment Viewer, double-click the icon to start DTM
Works.

13
TI 04R01B01-01EN Dec. 12, 2011-00
4. Click [Congure/Setup] of [AI1 Temp] from [Device Conguration] and select the [Conguration] tab.
For FieldMate R2.04.01, [Device Conguration] is under [Menu (online)].
5. Select the [O/S] checkbox in [Mode. Target] of [Block Mode] and click [Apply parameters] ([Download to device]
for R2.04.01). The changed mode (O/S) is displayed in [Mode. Actual].

14
TI 04R01B01-01EN Dec. 12, 2011-00
6. Congure the settings shown in Table 5 for the respective parameters of AI1 Temp. When conguration of the
respective parameters is complete, click [Apply parameters] ([Download to device] for R2.04.01).
Table 5 Parameter Settings
Item Parameter AI1 Temp to AI8 Temp
Scale High Limit Scale.EU at 100% 100.0
Scale Low Limit Scale.EU at 0% 0.0
Unit Scale Unit Index °C (degC)
Input Type Lin Type Type K
Data Type Process Value Type Direct
7. Select the checkbox for Auto in [Mode. Target] of [Block Mode] and click [Apply parameters].
8. Repeat steps 4 to 7 for setting AI1 Temp to congure the settings for AI2 Temp to AI8 Temp.
9. When conguration of the respective settings is complete, click the connection/disconnection icon (disconnect)
in DTM Works to exit DTM Works.

15
TI 04R01B01-01EN Dec. 12, 2011-00
10. Click [Exit] from the File menu to exit FieldMate.
3.3 Conguring the Network (Communication)
and Registering the Device (Step 3)
3.3.1 Conguring Network (Communication)
1. Start Field Wireless Congurator from the Start menu of PC1.
2. When the Login dialog box appears, enter “admin” in Login Name and Password and click [OK].
3. Click [New Project] from the File menu.

16
TI 04R01B01-01EN Dec. 12, 2011-00
4. Congure the settings shown in Table 6, such as Network ID and Network Information.
Note 2 : Do not change the setting
Note 1
Note 1: The ISA100.11a eld wireless network uses the wireless frequency bandwidths for the respective channels dened in the IEEE
802.15.4. Clear the check boxes for the channels whose use is prohibited by the law of your country.
Note 2: Do not change the settings in the System Manager/Security Manager eld.
• Max Nodes
• Max Latency
• Max Device Timeout
• Advertise Period
• Join Links Period
Table 6 Network Information
Item Settings Remarks
Network ID 100 The YFGW710 works with the network ID
specied here.
IP Address 192.168.0.101 Field Wireless Congurator will access
the YFGW710 that is specied here.
Subnet Mask 255.255.255.0
Default Gateway 192.168.0.1
NTP Server IP Address 192.168.0.1 If the server is not used, set the same IP
address as that of Default Gateway.
Topology Star
Channel Select the check boxes for the channels to be
used.
Clear the check boxes for the channels whose
use is prohibited by the law of your country or
region.
Note: The IP address set in YFGW is needed to change the settings next time. Write down the IP address for future reference.
5. When the conguration of the respective parameters is complete, click [Apply Changes]. When the conrma-
tion dialog appears, click [OK].

17
TI 04R01B01-01EN Dec. 12, 2011-00
3.3.2 Registering the Device (YTMX)
Import the provisioning information and register the device (YTMX) with the YFGW. Copy the provisioning infor-
mation le (YTMX-Prov.ypif) that was exported (saved to PC2) in Step 1 Provisioning to PC1.
n Importing the Provisioning Information
1. Click the [Devices] tab and click the [Open File] icon.
2. Select the le (YTMX-Prov.ypif) from the location to which the provisioning le was copied, and click [Open].
When the dialog box to conrm whether to load the provisioning le appears, click [Yes].
* If the network IDs of Field Wireless Congurator and the provisioning le are not identical, the provisioning le will not open.
3. When the Device Provisioning window appears, click [OK].
When the message to conrm whether to add the device le appears, click [OK].

18
TI 04R01B01-01EN Dec. 12, 2011-00
n Loading CF/DD File
1. Double-click the displayed Device Tag.
2. When the Edit Device window appears, click [Load CF/DD]. Select the CF le (00010101.c󰀨) for the YTMX
and click [Open]. (Default: c:¥Program Files¥Yokogawa¥DTM¥DTMev¥EV¥ISA100¥00594543¥1802)
n Setting Device Role
Set [IO] in [Device Role] (uncheck the box for Router) and click [Apply].

19
TI 04R01B01-01EN Dec. 12, 2011-00
n Setting Publication Period
Click the [Sampling Data] tab, click [DIAG_STATUS] of [UAP 2] [UAPMO_01] of Available Parameter, and click
the [>] button.
Set 2 (sec) in [Publication Period (sec)] and click [Apply].
When the conrmation message appears, click [OK].
n Setting Modbus Resisters
Map the process data (parameters) to the registers of the YFGW according to the settings below.
Parameter Input Register Number
UAPMO_01 DIAG_STATUS 0
AI_01 PV 3
AI_02 PV 6
AI_03 PV 9
AI_04 PV 12
AI_05 PV 15
AI_06 PV 18
AI_07 PV 21
AI_08 PV 24
1. Click the [Modbus Conguration] tab. Drag DIAG_STATUS to position 0 of Input Register.

20
TI 04R01B01-01EN Dec. 12, 2011-00
2. Drag PV of AI_01 to position 3 of Input Register.
3. Repeat the same operation for AI_02 to AI_08 to map the parameters to the registers.
4. When the mapping of the parameters is complete, click [Apply Changes].
n Saving Project File
1. Click [Save Project As] from the File menu.
2. Enter “YTMX” in File Name and click [Save].
Note: The saved le is needed to change the settings next time. Keep it for future use.