York YFGE18BXEXBH-RX Installation instructions

INSTALLATION AND OWNER’S MANUAL
Please read this manual carefully before using this air conditioner
Please keep this manual safely for future use
YFGE18BXEXBH-RX
YFGE24BXEXBH-RX
0150521922

DP482AKEAA
CE
All the products are in conformity with the following European provision:
- Low Voltage Directive
- Electromagnetic Compatibility
ROHS
The products are fulfilled with the requirements in the directive 2011/65/EU of the
European parliament and of the council on the Restriction of the use of Certain Haz-
ardous Substances in Electrical and Electronic Equipment (EU RoHS Directive) .
WEEE
In accordance with the directive 2012/19/EU of the European parliament,
herewith we inform the consumer about the disposal requirements of the
electrical and electronic products.
DISPOSAL REQUIREMENTS:
Your air conditioning product is marked with this sym-
bol. This means that electrical and electronic products
shall not be mixed with unsorted household waste.
Do not try to dismantle the system yourself: the dis-
mantling of the air conditioning system, treatment of
the refrigerant, of oil and of other part must be done
by a qualified installer in accordance with relevant
local and national legislation.
Air conditioners must be treated at a specialized treatment facility for re-use,
recycling and recovery. By ensuring this product is disposed of correctly, you
will help to prevent potential negative consequences for the environment and
human health. Please contact the installer or local authority for more infor-
mation. Battery must be removed from the remote controller and disposed of
separately in accordance with relevant local and national legislation.
EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS:
1
1+2= kg
R410A
2kg
2=
1= B
C
D
FE
kg
Containsfluorinated greenhouse gases
covered by the Kyoto Protocol A
This product contains fluorinated greenhouse gases covered by the Kyoto
Protocol. Do not vent into the atmosphere.
Refrigerant type: R410A
GWP:
2088
* GWP = global warming potential
Please fill in with indelible ink,
• 1 the factory refrigerant charge of the product
• 2 the additional refrigerant amount charged in the field and
• 1+2 the total refrigerant charge
on the refrigerant charge label supplied with the product.
The filled out label must be adhered in the proximity of the product charging
port (e.g. onto the inside of the stop valve cover).
A contains fluorinated greenhouse gases covered by the Kyoto Protocol
B factory refrigerant charge of the product: see unit name plate
C additional refrigerant amount charged in the field
D total refrigerant charge
E outdoor unit
F refrigerant cylinder and manifold for charging
IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED

2
Contents
Cautions
Safety Precautions
Parts and Functions
peration
Cleaning and Care
peration Tips
Troubleshooting
Installation Procedure
Test Run
3
5
6
8
18
19
20
24
32

Cautions
3
Disposal of the old ai conditione
Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air
conditioner in order to avoid the risk of child entrapment.
It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable
materials contained in a air conditioner can be recycled. Contact your local waste disposal center for proper disposal of an old
air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of
your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center, and contribute to
environmental awareness by insisting on an appropriate, anti-pollution method of disposal.
Disposal of the packaging of you new ai conditione
All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to
the environment.
The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping
bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon.
All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.
Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal
services nearest to your house.
Safety Inst uctions and Wa nings
Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very
important observations relating to the assembly, operation and maintenance of the air conditioner.
The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following
instruction.
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Installation shall be done by professional people. Don't install unit by yourself.
For the purpose of safety, the air conditioner must be properly grounded in accordance with specifications.
Always remember to unplug the air conditioner before opening inlet grill. Always grip plug firmly and pull straight out from
the outlet.
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger
for the user of the air conditoiner.
Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes
with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts
out and gets into eyes, it may result in serious eye injuries.
Do not obstruct or cover the ventilation grille of the air conditioner. Do not put fingers or any other things into the inlet/outlet
and swing louver.
Do not allow children to play with the air conditioner. In no case should children be allowed to sit on the outdoor unit.
When the indoor unit is turned on, the PCB will test if swing motor is .K., and then fan motor will start up.So there is a
few seconds to wait.
In cooling mode,the flaps will swing automatically to a fixed position for anti-condensating.

Cautions
4
Tempe atu e and Humidity Range
If the air conditioner is used under higher temperature condition than those listed, the built-in protection circuit may operate
to prevent internal circuit damage. Also, during Cooling and Dry modes, if the unit is used under conditions of lower
temperature than those listed above, the heat-exchanger may freeze, leading to water leakage and other damage.
Do not use this unit for purposes other than cooling, heating, dehumidifying and ventilation of rooms in ordinary dwellings.
The wiring method should be in line with the local wiring standand.
The waste battery should be disposed properly.
The air breaker should be all-pole switch and the distance between it's two contacts should be no less than 3mm.
Cooling
Heating
Indoor temperature
utdoor temperature
Indoor temperature
utdoor temperature
max. DB/WB
min. DB/WB
max. DB/WB
min. DB/WB
max. DB/WB
min. DB/WB
max. DB/WB
min. DB/WB
N- FF Inverter
32/23 C
18/14 C
43/26 C
10 C
27 C
15 C
24/18 C
-7 C
32/23 C
18/14 C
43/26 C
-5 C
27 C
15 C
24/18 C
-
15 C
Specifications
The refrigerating circuit is leak-proof.
For all the models in this manual, the all-pole discon-nexion connection method should be applied in the power supply.
Such means for disconnection must be incorporation in the fixed wiring.

YFGE24BXEXBH-RX,YFGE18BXEXBH-RX:
YFGE24BXEXBH-RX:
YFGE24BXEXBH-RX:

Pa ts and Functions
6
Note :
For the wired control type unit, the unit state should be checked by the wired controller, instead of the remote receiver.
and if you set the TIMER function, the TIMER LED on the remote receiver will not be on.
(1) perating Control Panel
(2) Emergency Switch
(3) Remote Control Signal Receiver
(4) Power Indicator Lamp (Red)
(5) peration Indicator Lamp (Green)
(6) Timer Indicator Lamp (Yellow)
(7) Compressor Run Lamp (Green)
(8) Intake Grill
(9) Air Filter
(10) UP/D WN Air Direction Flaps
(11) RIGHT/LEFT Air Direction Louvers (behind UP/D WN Air Direction Flaps)
10 11
3
9
8
1
4
5
6
7
2
3
P WER
PER
TIMER
C MP
EMER

7
Parts and Functions
2.Select operation mode
Press F N SPEED button. For each press, fan speed
follows:
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1oC,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1oC,if kept depressed, it will decrease
rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
ir conditioner is running under displayed fan speed.
When F N is set to UTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
LOW MED HI UTO
1. Unit start
Press ON/OFF on the remote controller, unit starts.
TEMP+
TEMP-
TEMP+ TEMP-
/
Base Operation
Remote controller
changes as
SPEED
Operation
Mode
UTO
etomeR
rellortnoC Note
COOL
DRY
F N
In DRY mode, when room temperature becomes
lower than temp.setting+2oC,unit will run intermittently
at LOW speed regardless of F N setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner automatically adjusts the fan speed
temperature.
When F N is set to UTO, the
according to room
In F N operation mode, the unit will not operate in
COOL or HE T mode but only in F N mode , UTO is
not available in F N mode. nd temp.setting is disabled.
In F N mode,SLEEP operation is not available.
Display
Board
UTO COOL DRY F N HE T
HE T

8
O eration
Sleep Operation
If the wind speed is high or middle before
setting for the sleep, set for lowing the wind
speed after sleeping.
If it is low wind, no change.
5.Set the wind speed change when sleeping
Use of SLEEP function
Operation Mode
1. In COOL,DRY mode
SLEEP operation starts SLEEP operation stops
SLEEP
operation starts
SLEEP
operation stops
pprox.6hrs
1 hr
1 hr
1 hr
3 hrs
3 hrs
Rises 1OC
Rises 1OC
Rises 1OC
Temp.setting
Temp.setting
Unit stop
Unit stop
In COOL, DRY mode
In HE T mode
Decreases 2OC
Decreases 2OC
1 hr
2.
3.
In HE T mode
In UTO mode
4. In F N mode
It has no SLEEP function.
Note
When TIMER function is set, the sleeping function
can't be set up . fter the sleeping function is set up,
if user resets TIMER function, the sleeping function
will be cancelled;the machine will be in the state of
timing-on.
POWER/SOFT Operation
Before going to bed,you can simply press the SLEEP
button and unit will operate in SLEEP mode and bring
you a sound sleep.
fter the unit starts,set the operation status,
then press SLEEP button before which the
clock must be adjusted and time being set.
1 hours after SLEEP mode starts,temp.will become
1 higher than temp.setting. fter another 1 hours,
temp.rises by 1 futher.The unit will run for further
6 hours then stops Temp. is higher than temp.
setting so that room temperature won
be too low
for your sleep.
1 hours after SLEEP mode starts,temp will
become 2 lower than temp.setting. fter
another 1 hours,temp decrease by 2
futher. fter more another 3hours,temp.rises
by 1 futher.The unit will run for further 3
hours then stops.Temp.is lower than temp.
setting so that room temperature won
be
too high for your sleep.
The unit operaters in corresponding sleep mode
adapted to the automatically selected operation
mode.
OC
OC
OC
OC
OC
(1) POWER Operation
(2) SOFT Operation
Press POWER/SOFT button again ,POWER or SOFT
disappears.
To cancel POWER or SOFT operation
Note £”
When you need rapid heating or cooling, you can use this
function. In COOL mode, fan speed automatically takes
high speed of UTO fan mode. In HE T mode, fan speed
automatically takes medial speed of UTO fan mode.
You can use this function when silence is needed for
rest or reading. In SOFT operation mode, fan speed
automatically takes low speed of UTO fan mode.
During POWER operation, in rapid HE T or COOL
mode ,
distribution. Long period SOFT operation will cause
effect of not too cool or not too warm.
NOTE:
Cooling only unit do not have displays and functions
related with heating.