Yoshimura 070BG126501 User manual

RESEARCH&DEVELOPMENT OF AMERICA, INC.
www.yoshimura-rd.com
FENDER ELIMINATOR KIT
070BG126501
Honda CBR650F
5420 DANIELS STREET STE A, CHINO CA., 91710 · [phone] · [phone] · FACSIMILE [phone]
THIS PRODUCT IS NOT DOT APPROVED.
Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the
installation of this product. Check with local laws and regulations for compliance prior to
installation and use. This product is not intended for use on public highways.
! !

No.
Item
Description
Qty.
1
12650-FEBKT1
Fender Eliminator Bracket 1
1
2
12650-FEBKT2
Fender Eliminator Bracket 2
1
3
12200-FEBKT
License Plate bracket
1
4
070BG-LH-K1
LED License Plate Light
1
5
070BG-LPF
License Plate Frame
1
6
12650-TSB-L
Left Turn Signal Bracket
1
7
12650-TSB-R
Right Turn Signal Bracket
1
8
M6X22BHS
6mm x 22mm Button Head Screw
1
9
M6X20BHS
6mm x 20mm Button Head Screw
2
10
M6X16BHS
6mm x 16mm Button Head Screw
2
11
M6X10BHS
6mm x 10mm Button Head Screw
4
12
M4X6BHS
4mm x 6mm Button Head Screw
2
13
6X12X7SPCR
Aluminum Spacer
1
14
6X12X6SPCR
Aluminum Spacer
2
15
6MMWASHER
6mm Washer
4
16
6MMLN
6mm Nylon Lock Nut
7
17
M6X14BHS
6mm x 14mm Button Head Screw
2
**
BN-SSS-22-18
Butt Connectors
2
**
ZT-300
Cable Ties
3
**
17029
Yoshimura Sticker Sheet
1
Optional Parts
***
070BGUNVTBKT
Universal Turn Signal Bracket Kit
2
14
11
13
16
16
1
2
3
4
5
67
8
9
17
10
11
12
15
*** The Yoshimura Universal Turn Signal Bracket Kit is to be used with aftermarket stud-mounted turn signals and is sold separately.

1. Remove passenger seat.
2. Disconnect the license plate light and turn signal
wires.
3. While securely supporting the stock fender
assembly, remove the three bolts and carefully
remove the stock fender assembly.
4. Disassemble the stock fender assembly and
remove left and right turn signals.
5. Cut the stock license plate light connector from
the stock fender assembly. Be sure to cut at
least a 6” section of wire from the connector.
Removal
Installation
1. Install (No. 4) 070BG-LH-K1, Yoshimura license
plate light onto (No. 3) 12200-FEBKT, Yoshimura
license plate bracket using (No. 12) M4X6BHS,
4mm button head screws provided in the kit.
3
4
12
3. Install (No. 3) 12200-FEBKT, Yoshimura license
plate bracket onto (No. 2) 12650-FEBKT2,
fender eliminator bracket using (No. 11)
M6X10BHS, 6mm screws as shown below.
3
2. Assemble (No. 1) 12650-FEBKT1, fender
eliminator bracket 1 to (No. 2) 12650-FEBKT2,
fender eliminator bracket 2 as shown below.
Note: Use (No. 8) M6X22BHS, 6mm screw to
align all holes when installing (No. 11)
M6X10BHS, 6mm screws.
1
11
2
8
11
3
2
4. Using the BN-SSS-22-18, butt connectors
provided in the kit, connect Yoshimura license
plate light wires to the stock license plate light
wires as follows:
Red -to- Brown
Black -to- Green
a) Strip the stock fender light wire ends
1/4” - 1/2” and insert into BN-SSS-22-18,
butt connectors provided in the kit.
b) Center the spliced wire ends in the
middle and using a heatgun or lighter,
apply heat evenly on the outer edges of
the butt connector to shrink and hold
wires in place.
c) Making sure that the stripped ends are
centered, heat the center of the butt
connector evenly until the solder begins
to liquify.
d) Allow to cool completely and tug both
ends of the wires to verify that connection
is secured.
Scan for link to butt connector instruction video.
5. Install the stock left and right turn signals onto
(No. 6,7) 12650-TSB-L/R, turn signal brackets.

3
6. Install (No. 6,7) 12650-TSB-L/R, left and right
turn signal brackets and (No. 5) 070BG-LPF,
license plate frame using (No. 10, 17)
M6X16BHS & M6X14BHS, 6mm screws,
(No. 15) 6MMWASHER, washers, and (No. 16)
6MMLN, nuts as shown below.
7. Route license plate light and turn signal wires
through hole in (No. 1,2) 12650-FEBKT1/2,
fender eliminator bracket and then under the
passenger seat and reconnect.
8. Install (No. 1) 12650-FEBKT1, fender eliminator
bracket onto subframe using (No. 8,9)
M6X22BHS and M6X20BHS, 6mm button head
screws as shown.
1
Note : (No. 13,14) 6X12X7SPCR and
6X12X6SPCR, aluminum spacer mounts
between (No. 1) 12650-FEBKT1, fender
eliminator bracket and the subframe.
2
Note : (No. 13) 6X12X7SPCR, aluminum spacer
is 1mm larger than (No. 14) 6X12X6SPCR.
9. Re-install passenger seat.
10. Check for proper function of license plate light,
turn signals, brake light, and that all brackets
and componets are secure prior to riding.
17
10
56
7
15
16
9
14
13
8
1