ZALMAN CNPS11X Extreme User manual

User's Manual
CNPS11X Series
Ver. 121106
To ensure safe and easy installation, please read
the following precautions
www.ZALMAN.com
Intel Socket 2011/1366/1156/1155/775 CPUs
AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2 CPU&APUs

2
.COM
EnglishEnglish
1. Precautions
2. Specications
1) Avoid inserting objects or hands into the fan while it is in operation to prevent
product damage and injuries.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and eyes.
If contact is made with skin, wash off with water. If ingested or irritation persists,
seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this product.
4) Excessive force exerted on the fan may cause damage to the fan and/or
system.
5) Use and keep product away from reach of children.
6) Check the components list and condition of the product before installation.
If any problem is found, contact the retailer to obtain a replacement.
7) During transportation of the system, the cooler must be removed. Zalman is not
responsible for any damages that occur during the transport of a system.
8) Product design and specications may be revised to improve quality and
performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to
external causes, including but not limited to, improper use, problems
with electrical power, accident, neglect, alteration, repair, improper
installation, or improper testing.
Model
Spec. CNPS11X Extreme CNPS11X Performa
Material
Pure Copper and Aluminum Pure Copper and Aluminum
Weight 600g 450g
Dimensions 135(L) Ⅹ 80(W) Ⅹ 154(H)㎜ 135(L) Ⅹ 80(W) Ⅹ 154(H)㎜
F
A
N
Bearing Long Life Bearing Long Life Bearing
Quiet
Mode
RPM 1,000 ~ 1,400rpm ± 10%
Noise
Level 17dBA ~ 24dBA ± 10%
Normal
Mode
RPM 1,000 ~ 1,950rpm ± 10% 1,000 ~ 1,600rpm ± 10%
Noise
Level 17dBA ~ 33dBA ± 10% 17dBA ~ 26dBA ± 10%
Thermal
Grease
Contents
3.5g 1g
Temperature
Range
-40℃~+150℃
(-40~+302℉)
-40℃~+150℃
(-40~+302℉)

3
.COM
English
3. Components
1) Common Components
AMD Clip
Intel Clip
2) Intel Components 3) AMD Components
Socket 2011/1366/1156/1155/775 Socket FM2/FM1/AM3+/AM3/AM2+/AM2
11X Extreme
Thermal Grease
[ZM-STG2]
11X Performa
Thermal Grease
[ZM-STG2M]
Loading Block Nuts Double-sided Tape
Backplate
11X Extreme
Resistor
[RC24P]
Cooler
Side Cap
Wrench
Silver Bolts B (3mm)
(Socket 1156/1155/775/AMD)
Silver Bolts A (4mm)
(Socket 2011)
Gold Bolts
(Socket 1366 )
User’s Manual

4
.COM
EnglishEnglish
4. Installation Requirements
CNPS11X Extreme CNPS11X Performa
1) Space Requirements
2) Air Guide Removal
3) Cooler Orientation
100 mm
137 mm
155 mm
The cooler’s installation requires an unobstructed space of 137mm(width),
100mm(length), and 155mm(height), with the CPU as a central reference point.
Please check if components such as ODDs and PSU protrude into the required space.
Air guides on enclosures must be removed before the cooler’s installation since
they protrude into the cooler’s required space.
As shown in the diagram below, it is recommended that the cooler be installed so that air
ows from the cooler toward the enclosure’s rear exhaust fan to be released.
※Recommended cooler orientation may differ according to the motherboard model.
Case Cover
Air guides

5
.COM
English
5. Installation
A.
Intel Socket Installation
1) Intel Socket 2011 Installation
- Unfasten the Bolts on the Cooler’s Base one thread, insert the Intel Clip
between the Cover and the Base, and then refasten the Bolts.
Make sure the Intel Clip’s ingresses
are ush against
the protrusions of
the Base Cover.
Align
Intel Clip
- Apply a suitable amount of the included Thermal Grease on the CPU’s
surface and then fasten the Bolts to install the cooler.
Check the size of the silver-
colored bolts before installing
because silver-colored bolt A
and B have similar color. Gold Bolts
(Socket 1366)
Sliver Bolts A (4mm)
(Socket 2011)
Sliver Bolts B (3mm)
(Socket 1156/1155/
775/AMD)
Sliver Bolt A
(4mm)
Wrench
Caution
Caution

6
.COM
EnglishEnglish
Socket 775
Socket 1156/1155
Socket 1366
Take note of the orientation of the Nuts and the Side Caps.
X
O
Caution
2) Intel Socket 1366/1156/1155/775 Installation
①
Install Bolts to the Backplate according to the Socket Type and secure
with Side Caps.
1
2
② Socket 1366/1156/1155 Installation
Attach Double-sided Tape to the center of the Backplate and remove
the Double-sided Tape’s Cover.
※ Socket 1366/1156/1155 Installation does not require the Loading Block.
Double-sided Tape

7
.COM
English
③
Socket 775 Installation
Remove the Sticker Cover from the Lower Tier of the Loading Block and attach
to the Backplate.
Attach Double-sided Tape to the Loading Block and remove
the Double-sided Tape Cover.
Double-sided Tape
Loading Block
X
O
Caution
Please make note of the orientation of the Loading Block’s Installation.

8
.COM
EnglishEnglish
Please make sure that PWM Control Mode is activated in the
motherboard’s BIOS settings.
Caution
④
Align the Backplate’s Nuts with
the motherboard’s Clip Support
installation holes and then fasten
to the motherboard.
M/B
⑥
Connect the cooler’s 4-pin connector to the
motherboard’s CPU Fan header.
M/B
M/B
Gold Bolt
(Socket 1366)
Sliver Bolt B (3mm)
(Socket 1156/1155/775)
Wrench
⑤ Apply a suitable amount of the included Thermal Grease on the CPU’s
surface and then fasten the Bolts to install the cooler.
Check the size of the silver-
colored bolts before installing
because silver-colored bolt A
and B have similar color. Gold Bolts
(Socket 1366)
Sliver Bolts A (4mm)
(Socket 2011)
Sliver Bolts B (3mm)
(Socket 1156/1155/
775/AMD)
Caution

9
.COM
English
1) AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2 Installation
①
Unfasten the Bolts on the Cooler’s Base one thread, insert the AMD Clip
between the Cover and the Base, and then refasten the Bolts.
Make sure the AMD Clip’s ingresses
are ush against the protrusions of
the Base Cover.
Caution
Align
② Install Bolts to the Backplate according to the Socket Type and secure
with Side Caps.
RC24P
(Fan RPM resistor)
Motherboard
Connector
Tip
[CNPS11X Extreme Only]
B. AMD Socket Installation
AMD Clip
1
2
For Quiet Mode, please
connect RC24P to the Fan
Connector.

10
.COM
EnglishEnglish
X
O
Take note of the orientation of the Nuts and the Side Caps.
Caution
③
Remove the Sticker Cover from the Lower Tier of the Loading Block
and attach to the Backplate.
Caution
Please make note of the orientation of the Loading Block’s Installation.
Attach Double-sided Tape to the Loading Block and remove
the Double-sided Tape Cover.
Loading Block
Double-sided Tape
O
X