Zavio B7210 User manual

0

1
Zavio B7210 Quick Installation Guide
Please follow the installation steps below to set up your B7210 Bullet IP Camera.
Check the package contents against the list below. See P.1
Physical overview. See P.2
I/O Terminal Block Pin Definition. See P.3
I/O Terminal Block Circuit. See P.3
LED Indicator Definition. See P.4
Power mode. See P.4
Install the hardware and connect all cables. See P.4
Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.7
Access the IP Camera using Intelligent IP Installer. See P.7
Mac OS using Safari Broswer. See P.9
Lighting environment. See P.10
Change the Web Interface into your preferred language. See P.10
Application of IP Camera. See P.11
For more information, please check the User Manual available in the Software CD or you can download the
latest software from http://www.zavio.com
Package Contents
Camera
B7210 2Megapixel IR Bullet Network
Camera
Quick Installation Guide
B
rief product information and quick installation
Software CD
IP Surveillance Software
Intelligen
t IP Installer
User Manuals
Language Packs
Accessory
Wall mount bracket &
U-shape bracket
Metal plate for wall mount bracket
Alignment Sticker
Waterproof Connector
Screw pack for sun shield & burglarproof screw
Screw pack for wall and ceiling mounting
Silica gel
Foam tape
2 pin terminal blocks for power

2
Physical overview
DI / DO
IR LED
Lens
Light Sensor
DC 12V/1.5A

3
I/O Terminal Block Circuit
I/O Terminal Block Pin Definition
PIN
Definition
Description
Max. V/A
1
Ground
-
2
+ 12V DC
12V DC
1.2W
3
AUDIO_In(+)
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
-
4
AUDIO_In(+)
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
-
5
Digital Output 1
Uses an NPN transistor with the emitter connected to the GND
pin. If used with an external relay, a diode must be connected in
parallel with the load for protection against voltage transients.
100 mA
24V
6
Digital Output 2
Uses an NPN transistor with the emitter connected to the GND
pin. If used with an external relay, a diode must be connected in
parallel with the load for protection against voltage transients.
100mA
24V
7
Digital
Input 1
Connected to GND to activate, or leave floating (or unconnected)
to deactivate.
30V DC
8
Digital
Input 2
Connected to GND to activate, or
leave floating (or unconnected) to deactivate.
30V DC
Digital Input 1/2: Max: 30V DC
Digital Output 1/2: Max: 24V / 100mA

4
LED Indicator
ōōņŅ
ġ
ġ
ńŰŭŰų
ġ
ŊůťŪŤŢŵŪŰů
ġ
ŏŦŵŸŰųŬ
ġ
ňųŦŦů
ġ
ŔŵŦŢťźġŨųŦŦůġŧŰųġŏŦŵŸŰųŬġŭŪůŬį
ġ
ŐųŢůŨŦ
ġ
ŇŭŢŴũġŰųŢůŨŦ
ġŸũŪŭŦġŏŦŵŸŰųŬġŢŤŵŪŷŪŵźġ
őŰŸŦų
ġ
œŦť
ġ
ŔŵŦŢťźġųŦťġŧŰųġţŰŰŵŪůŨġŶűġűųŰŤŦŴŴ
ġ
ŃŭŶŦ
ġ
ŔŵŦŢ
ťźġţŭŶŦġŧŰųġţŰŰŵŪůŨġŶűġŤŰŮűŭŦŵŪŰůġ
ŖůŭŪŵġ
ġ
ŸũŦůġųŦŴŦŵġţŶŵŵŰůġűųŦŴŴŦť
ġ
ŧŰųġŢŵġŭŦŢŴŵġĶġŴŦŤįġ
ŵŰġŧŢŤŵŰųźġťŦŧŢŶŭŵ
ġ
ŎŪŤųŰġ
ŔŅġ
İġ
ŔŔŅʼnń
ġ
ŐųŢůŨŦ
ġ
ŔŵŦŢťźġŰųŢůŨŦġŮŦŢůŴġŔŅġŤŢųťġųŦŢťź
ġ
ŇŭŢŴũŦŴġŰųŢůŨŦġŸũŪŭŦġŢŤŤŦŴŴŪůŨġŔŅġŤŢųť
ġ
Power Mode
PoE Mode
Power
Requirement
őŰņġĩŊņņņĹıijįĴŢŧĪġŸŪŵũġńŭŢŴŴġĴġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ŏŰŵŦ
ĻġŘũŪŭŦġŊœġŰůĭġʼnŦŢŵŦųġŢůťġŇŢůġŸŪŭŭġţŦġťŪŴŢţŭŦťį ġġ
Power
Co
nsumption
ĴįĶĺŘĭġŸŪŵũŰŶŵġŊœİʼnŦŢŵŦųİŇŢůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ĸįĺŘĭġŸŪŵũġŮŢŹįġŊœġŰů
ġ
Adaptor Mode
Power
Requirement
IJijŗİIJįĶłġłťŢűŵŰųġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ŏŰŵŦĻġŘũŪŭŦġŊœġŰůĭġʼnŦŢŵŦųġŰųġŇŢůġŸŰŶŭťġţŦġŢŤŵŪŷŢŵŦťġŢŶŵŰŮŢŵŪŤŢŭŭźįġ ġ
Power
Co
nsumption
ĴįĶĹŘĭġŸŪŵũŰŶŵġŊœİʼnŦŢŵŦųİŇŢůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ĸįĺŘĭġŸŪŵũġŮŢŹįġŊœġŰůġ ġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ĺįķŘĭġŸŪŵũġŮŢŹįġŊœġŰůġİġʼnŦŢŵŦųġŰůġ ġġġġġġġġġġġġġġġġġġġġġġġġġġġ
ĹįĹĸŘĭġŸŪŵũġŮŢŹįġŊœġŰůġİġʼnŦŢŵŦųġŇŢů
ġ
Note: Heater will be activated while the inner temparature drops under 5ɗand fan over 50ɗ.
Install the hardware and connect all cables
a. Hardware Installing
1) Assembling sun shield and camera with two supplied screws(M3*6).
2) Fix U-shape bracket to the bottom of camera with supplied screws.
3) Insert all cables (RJ45/power cord/DIDO) into waterproof connector (M25*1.5).
4) Open the front cover and feed all cables through the screw hole of bottom cover from outside. Connect
them to sockets. Then secure the connector tightly.
5) Attach the foam tape and silica gel. (Please change a new silica gel if open the top cover afterwards.)
6) Lock the front cover. Then secure the burglarproof screw.
7) Feed all cables through the front opening of wall mount bracket.
8) Push the spring mortise of wall mount bracket. Then hook the U-shape bracket onto the groove of the
former.
9) Secure the two screws of wall mount bracket on the other side.

5
b. Wall mounting and Ceiling mounting
1) Attached the alignment sticker to the wall. Drill four holes into the wall, which three for screws and one
for cable. Then hammer the supplied plastic anchors into the screw holes and secure the plate with
supplied screws (T1/4”*32).
2) Hang the wall mount bracket on the plate and fix it with the supplier screw.
3) Adjust the angle of the wall mount bracket to aim the shooting area.

6
c. Lens Focusing
D. Connect all cables
d1. Without Power over Ethernet (PoE) connection
1. Connect the power adaptor to the IP Camera.
2. Using a standard RJ-45 network cable, connect the IP Camera
to a normal Hub / Switch / Router.
d2. Power over Ethernet (PoE)
Using a standard RJ-45 network cable, connect the IP Camera
to a PoE-enabled Hub / Switch / Router.

7
Microsoft OS:Use the software CD to install Intelligent IP Installer
Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow these
steps to install the firmware.
Access the IP Camera using Intelligent IP Installer
1. Please check two settings before using Intelligent IP Installer .
Select “Intelligent IP Installer” and follow the installation process to complete the installation.
b. Browser’s Internet Properties
ɦ
Privacy
ɦUncheck Pop-up Blocker
a. Browser’s Internet Properties
ɦ
Security
ɦDefault Level
2. Click the Intelligent IP Installer Icon on your desktop. The main page will show up listing all active
camera and video server
devices. Select the relevant IP camera from the list and click Link to IE.

8
3. Enter your Username and Password
to login
to the IP Camera.
(
Default is admin / admin)
4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar:
This website wants to install the following add
-on: ‘AxvideoView.cab from ‘Zavio Inc’.
5. Click the information bar, and select Install ActiveX control.
6. Click Install.

9
Mac OS using Safari Browser
7. Live video displays in the centre of your web browser.
1. Select Safari icon
2. Click Bonjour function and select the camera
you wish to access.
4. The monitor image will be displayed in your browser.
3
. Enter name and password to login to the IP
camera. (
Default is admin / admin)