Zelart SUB1101U User manual

BACK TRAINER
SUB1101U
ASSEMBLY INSTRUCTIONS

EXPLODED DRAWING

PARTS LIST
NUMBER
DESCRIPTION QUANTITY
1
MAIN
SUPPORT
1
2
FRONT
SUPPORT
1
3 CUSHION POST 1
4
FOAM
ROLL POST
1
5
LEFT
HAND
RAIL
1
6 RIGHT HANDRAIL 1
7
FOAM TUBE
1
8
BOTTOM S
TABILIZER
2
9 REINFORCEMENT PLATE 1
10
CUSHION
1
11
FOAM ROLLER
2
12 FAST PIN 1
13
SECURING KNOB
1
14
PIN
1
15 SCREW M8*16 + WASHER 2
16
SCREW M
8
*20 + WASHER
2
17
SCREW M10*65 + TWO WASHERS +
LOCK
NUT
4
18 SCREW M10*70 + TWO WASHERS + LOCK NUT 2
19
SCREW M10*75 + TWO WASHERS + LOCK NUT
1
ASSEMBLY INSTRUCTIONS
1. Insert the bottom stabilizer (8) into the main support (1) and secure with screw
M8*16 + washer (15) and screw M10*65 + two washers + lock nut (17).
2. Insert the bottom stabilizer (8) into the front support (2) and secure with screw
M8*16 + washer (15) and screw M10*65 + two washers + lock nut (17).
3. Attach front support (2) to main support (1) with screw M10*75 + two washers +
lock nut (19) and pin (14).

4. Attach foam roll post (4) to main support (1) with reinforcement plate (9) and
screws M10*70 + washers + lock nuts (18).
Note: There are two sets of holes in the main support (1) which allows you to attach
the foam roll post (4) to two different positions. Try the upper position first.
5. Slide a foam roll (11) onto the foam tube (7). Insert the other end of the foam tube
(7) through the upper hole in the foam roll post (4). Slide another foam roller (11)
over the protruding end of the foam tube (7).
Note: There are two adjustment holes in the foam roll post (4). These adjustment
holes allow users to adjust the position of the foam rollers (11). Try the upper hole
first.
6. Insert the cushion post (3) into main
support (1) and lock in position with
the fast pin (12). For added safety,
thread the securing knob (13) into
the right side of the main support (1).
Note: The pin of the fast pin (12) must be
inserted into one of the adjustment holes
in the cushion post (3). The fast pin (12)
and securing knob (13) must be screwed
in tightly to ensure that the cushion post
(3) will fit securely in the main support
(1).
7. Attach the left and right handrails (5,
6) to both sides of the cushion post
(3) with screw M10*65 + two
washers + lock nut (17).
8. Attach the cushion (10) to the
cushion post (3) with screw M8*20
+ washer (16).

CUSHION HEIGHT ADJUSTMENT
To adjust the height of the cushion (10), loosen
but do not remove the securing knob (13).
Loosen and pull the fast pin (12), slide the
cushion (10) to the desired position, and secure
with the fast pin (12). Tighten the fast pin (12)
and securing knob (13).
NOTE: The pin of the fast pin (12) must be
inserted into one of the adjustment holes in the
cushion post (3). The fast pin (12) and securing
knob (13) must be screwed in tightly to ensure
that the cushion post (3) will fit securely in the
main support (1).
STORAGE
1. To store the Hyper Bench, simply keep it in a clean dry place.
2. Use two people to lift from the left and right handrails (5, 6) and rear stabilizer
(8) to move the Hyper Bench.
3. Follow the process below to fold the Hyper Bench as illustrated for easy storage.
a. Loosen but do not remove the securing knob (13). Loosen and pull the fast pin
(12), slide the cushion (10) to the lowest position. Then lock in position by
tightening the fast pin (12) and securing knob (13).
b. Remove the pin (14) to fold the front support (4). Store the pin (14) in the hole in
the main support (1).
c. The Hyper Bench should appear as shown in illustration B after folded.