Zenith 9012SS User manual

s and hardware.
Pg 1of 10
BB 04/17/06
IS9012-I7
Assembly Instructions - Model 9012SS (Chrome)
©2006 Zenith Products Corp.
Before You Begin
Thank you for purchasing this prod-
uct. We’ve included easy to follow
step-by-step instructions which have
been carefully written to ensure
quick, easy assembly of your furni-
ture. Be sure to read the instructions
(a time saver in the long run).
Identify all part
.

Pg 2of 10
Tools Needed
List of Parts
(J) 4 Wall Anchors
(H) 4 Mounting Screws
(A) 4 Large Screws
(G) 8 Rubber Shelf Collars
(E) 4 Top Caps
(F) 4 Bottom Caps
(C) 24 Chrome Collars
(D) 4 Threaded Inserts
(B) 1 Allen Wrench for use with
Large Screws (A)
(I) 4 Mounting Spacers
NOTE: tools only needed for mounting
to wall, not for assembly
IS9012-I7

Pg 3of 10
(3) 2 Tubular Shelves
(5) 4 Short Tubes
(4) 2 Glass Shelves
(2) 1 Bottom Piece
(1) 1 Top Piece
(8) 4 Thin Interior Tubes
(7) 4 Long Tubes
(6) 4 Medium Tubes
4 Tubos medianos
4 tubes moyens
IS9012-I7

1.
2.
Screw threaded inserts (D) into one end of
thin interior tubes (8).
Screw thin interior tubes (8) into top piece
(1).
Pg 4of 10
D
8
1
D
IMPORTANT:Make sure top piece (1) is oriented like this.
Please note:For ease of assembly, this
product is being assembled upside down.
8
IS9012-I7

3.
4.
Slide chrome collars (C) and short tubes (5)
onto thin interior tubes (8).
Slide a tubular shelf (3), chrome collars (C)
and long tubes (7) onto thin interior tubes
(8).
8
5
C
C
3
7
8
NOTE:The cross wires should be face up.
Pg 5of 10 IS9012-I7

5. Slide chrome collars (C) and a tubular shelf
(3) onto thin interior tubes (8).
Pg 6of 10
3C
8
NOTE:The cross
wires should
be face up.
IS9012-I7

Pg 7of 10
Slide medium tubes (6) and chrome collars
(C) onto thin interior tubes (8). Fasten bot-
tom piece (2) to unit with large screws (A).
6.
6
C
A
2
IMPORTANT:Make sure bottom
piece (2) is oriented like this.
Make sure all chrome collars
(C) are straight and properly
aligned before tightening
large screws (A).
IS9012-I7

Pg 8of 10
7. Screw on top caps (E).
F
IMPORTANT:
Once bottom caps (F) are inserted, they
CAN NOT be removed without causing
damage to the unit. Be sure to confirm
that unit is properly assembled and tight-
ened before inserting bottom caps (F).
8. Insert bottom caps (F).
E
IS9012-I7

9. Mount the unit to the wall.
WARNING: FOR SAFETY REASONS, IT IS
IMPERATIVE THAT THIS UNIT BE
MOUNTED TO THE WALL. WE HAVE
PROVIDED MOUNTING HARDWARE FOR
YOUR CONVENIENCE.
Mounting Instructions:
Warning: Before cutting, drilling or ham-
mering into any wall surface, verify the
location of electrical, plumbing and gas
lines. Cutting any of these may cause
serious injury.
1. Mark mounting points on wall through
holes in the back tubes of the unit.
2. Hammer wall anchors (J) into wall, unless
mounting screws (H) will go directly into a
stud. (NOTE: Do not use a wall anchor if
mounting screw will be going into a stud.)
Wall anchors (J) should be oriented with the
flat side horizontal.
3. Place unit against wall, lining up wall
anchors (J) and holes in rear tubes.
4. Complete mounting by tightening mount-
ing screws (H) through mounting spacers (I)
into studs or wall anchors (J).
Pg 9of 10
H
I
J
Wall anchors (J) should be oriented with the flat side horizontal.
IS9012-I7

Pg 10 of 10
4
4
G
10. Install rubber shelf collars (G).
Install glass shelves (4).
11.
IS9012-I7
Learn more about other home bath & faucets by Zenna Home on our website.