ZIEHL-ABEGG AM-PREMIUM User manual

AM-PREMIUM(-W)
Universal control module for ZIEHL-ABEGG ECblue fans and
frequency inverters of the Basic series
Operating Instructions
Keep for reference!
Software version: D1727A / D2263A from version 4.00
L-BAL-E095-GB 1618 Index 006 Part.-No.
english

Content
1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Structure of the operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 FCC / IC Statements (for AM-PREMIUM-W modules only) . . . . . . . . . . . . . . . . . . . . . 5
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Operational area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.4 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.5 Disposal / recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Mounting the module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 Analog inputs “E2” / “E3” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.3 Analog output (0 - 10 V) “A1” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4 Voltage supply 24 V DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.5 Connection external terminal type A-G-247NW or AXG-1A(E) . . . . . . . . . . . . . . . . . . . 8
5.6 Digital inputs “D1” and “E1 D2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7.1 Networking via MODBUS-RTU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7.2 RS-485 - network design and interface parameter . . . . . . . . . . . . . . . . . . . . . . . . 10
5.7.3 AM-PREMIUM-W Wireless Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.8 Potential at control voltage connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Operating by terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 Menu operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 Menu structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3 Example for programming mode 2.01 in “Base setup” . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Base setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Select operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.2 External Setpoint / External speed setting in manual operation . . . . . . . . . . . . . . . . . . 16
8 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.1 Prerequisites for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.2 Procedure for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.3 Menu Mode 1.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1 Speed controller 1.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1.1 Base setup 1.01 ............................................... 18
9.1.2 Setting for operation 1.01 ......................................... 18
9.2 Temperature control 2.01 ... 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.2.1 Basic setting 2.01 ... 2.05 ......................................... 20
9.2.2 Settings for operation modes 2.01 ... 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.2.3 Functional diagrams temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9.2.4 Additional for mode 2.03 : Signal output 0 - 10 V . . . . . . . . . . . . . . . . . . . . . . . . 24
9.2.5 For mode 2.03 : Relay output for Heating or Cooling . . . . . . . . . . . . . . . . . . . . . . 25
9.2.6 For mode 2.03 Relay output for temperature monitoring . . . . . . . . . . . . . . . . . . . . 26
9.3 Pressure control for condensers refrigeration 3.01 ... 3.04 . . . . . . . . . . . . . . . . . . . . . 26
Operating Instructions AM-PREMIUM(-W) – model series
L-BAL-E095-GB 1618 Index 006 Part.-No.
2/90

9.3.1 Base setup 3.01 ... 3.04 .......................................... 26
9.3.2 Setting for operation modes 3.01 and 3.02 ............................ 27
9.3.3 Functional diagrams pressure control condensers . . . . . . . . . . . . . . . . . . . . . . . . . 29
9.4 Pressure control airconditioning 4.01 ... 4.03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.4.1 Base setup 4.01 ... 4.03 .......................................... 30
9.4.2 Setting for operation modes 4.01 ... 4.03 .............................. 31
9.5 Volume control 5.01 ... 5.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
9.5.1 Basic setting 5.01 and 5.02 ....................................... 33
9.5.2 Setting for operation modes 5.01 ... 5.02 ............................... 33
9.6 Air velocity control 6.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9.6.1 Base setup 6.01 ............................................... 36
9.6.2 Settings for operation modes 6.01 ................................... 36
9.7 Menu group Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.8 Menu group Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.9 Controller Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.9.1 PIN protection activate, PIN0010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.9.2 Set protection activate, PIN 1234 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.9.3 Save user settings restore with PIN 9090 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.9.4 Sensor Alarm ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.9.5 Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.9.6 Minimum speed cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9.9.7 Second Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9.9.8 Reverse action of the control function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.9.9 Controller configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.9.10 Data on the total control deviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.9.11 LED Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.9.12 MODBUS communication watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.10 IO Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.10.1 Analog-Output “A” ............................................... 45
9.10.2 Digital inputs “D1” / “D2” (E1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.10.2.1 Menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.10.2.2 Enable ON/OFF function
| 1D | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.10.2.3 External fault Function
| 2D | ............................... 47
9.10.2.4 Limit ON / OFF, Function
| 3D | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.10.2.5 Switch over Input signal “E2” / “E3”, Function | 4D | . . . . . . . . . . . . . . . 48
9.10.2.6 Set 1/2 or Setpoint 1/2, Function
| 5D | . . . . . . . . . . . . . . . . . . . . . . . . 48
9.10.2.7 Intern / Extern Function
| 6D | .............................. 49
9.10.2.8 Automatic control / speed manual Function
| 7D | (mode 2.01 ) . . . . . . . 50
9.10.2.9 Reverse action of control function ( 2.01 ), Function
| 8D | . . . . . . . . . . . 50
9.10.2.10 Reset, Function
| 10D | ................................... 50
9.10.2.11 Setting Max. Speed ON / OFF function
| 11D | . . . . . . . . . . . . . . . . . . . 51
9.10.2.12 Direction of rotation, Function
| 13D | . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.10.2.13 “Freeze function” maintain momentary modulation value, Function | 14D |
51
9.10.3 Configuration of analog inputs “E1”and “E3” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.10.3.1 Signal adaption E2 and E3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.10.3.2 Inverting analog inputs “E2” / “E3” . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.10.3.3 “E2” / “E3” Bus mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.10.4 Function and inverting for relay outputs “K1” ............................ 55
9.10.5 Networking via MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.11 Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.11.1 Limit indication depending on modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.11.2 Limit indication depending on setting or sensor signal . . . . . . . . . . . . . . . . . . . . . . 58
9.11.3 Limit indication depending on (offset) to Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.12 Motor Setup for AM-PREMIUM in ECblue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.12.1 Setting for Rampup time and Rampdown time . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.12.2 Suppression of speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
9.13 Motor Setup for AM-PREMIUM in Fcontrol Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
9.13.1 Setting motor rated current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Operating Instructions AM-PREMIUM(-W) – model series
L-BAL-E095-GB 1618 Index 006 Part.-No.
3/90

9.13.2 Setting motor rated voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
9.13.3 Adjustment of the U/f curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
9.13.4 Setting for Rampup time and Rampdown time . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.13.5 Setting Rolling direct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.13.6 Setting Current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.13.7 Setting brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.13.8 Motorheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.13.9 Suppression of speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.14 Motor Setup for AM-PREMIUM in Icontrol Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.14.1 Setting motor rated current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.14.2 Setting motor rated voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.14.3 Adjustment of the U/f curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.14.4 Setting for Rampup time and Rampdown time . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
9.14.5 Setting switching Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.14.6 Setting Rolling direct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.14.7 Setting Current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.14.8 Setting brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.14.9 Setting Quench mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
9.14.10 Setting Overmodulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
9.14.11 Motorheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
9.14.12 Suppression of speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
10 Menu tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
10.1 Menu table for AM-PREMIUM in ECblue Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
10.2 Menu table for AM-PREMIUM in Icontrol / Fcontrol Basic . . . . . . . . . . . . . . . . . . . . . . 78
10.3 Possible allocation of the IOs, PINs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
11 Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
12 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
12.1 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
12.2 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
12.3 Manufacturer reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
12.4 Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Operating Instructions AM-PREMIUM(-W) – model series
L-BAL-E095-GB 1618 Index 006 Part.-No.
4/90

1 General notes
1.1 Structure of the operating instructions
These operating instructions only apply in conjunction with the mounting/operating instruc-
tions for the device in which this module is installed. The remarks concerning safety, installa-
tion and connection described there must be followed!
Before installation and start-up, read this manual carefully to ensure correct use!
1.2 Exclusion of liability
Concurrence between the contents of these operating instructions and the described hardware and
software in the device has been examined. It is still possible that non-compliances exist; no guarantee
is assumed for complete conformity. To allow for future developments, construction methods and
technical data given are subject to alteration. We do not accept any liability for possible errors or
omissions in the information contained in data, illustrations or drawings provided.
ZIEHL-ABEGG SE is not liable for damage due to misuse, incorrect use, improper use or as a
consequence of unauthorized repairs or modifications.
1.3 FCC / IC Statements (for AM-PREMIUM-W modules only)
The following specifications are intended for the use of the product in the USA or Canada. In the case
of translations of the document, these specifications are also written in the respective national
languages.
FCC Compliance (US)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and(2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
IC Compliance (Canada)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
2 Safety instructions
Information
Mounting, electrical connection, and start-up operation may only be carried out by an electrical
specialist in accordance with electrotechnical regulations (e.g. EN 50110 or EN 60204)!
Operating Instructions AM-PREMIUM(-W) – model series General notes
L-BAL-E095-GB 1618 Index 006 Part.-No.
5/90

Danger due to electric current
•It is generally forbidden to carry out work on electrical live parts. Protection class of the device
when open is IP00! It is possible to touch hazardous voltages directly.
•The 5 electrical safety rules must be observed!
•The safe isolation from the supply must be checked using a two-pole voltage detector.
•Even after disconnecting the mains voltage, life-threatening charges can appear between the
protective ground “PE” and the mains connection.
Waiting period at least 3 minutes!
Opening the device in which the module is to be installed (fan, inverter) is only allowed when the
mains power is switched off and after waiting at least three minutes.
Through use of capacitors, danger of death exists even after switching off the device through directly
touching the energized parts or due to parts that have become energized due to faults.
3 General description
3.1 Operational area
The add-on module can only be used together with compatible ZIEHL-ABEGG devices.
Note: The AM-PREMIUM-W module is intended exclusively for integration and utilisation in host
devices (fans and converters) from ZIEHL-ABEGG.
3.2 Function
By plugging on the “AM-PREMIUM” module, the fan / frequency inverter becomes a full universal
controller.
The module has two analog inputs (e.g. for sensors), one analog output and a MODBUS interface.
Type“AM-PREMIUM-W” additionally offers radio communication for parameterisation and data scan-
ning by the hand held terminal type A-G-247NW.
Type Part-No. Function
AM-PREMIUM 349046 Universal control module
AM-PREMIUM-W 349051 Universal control module
Communication by radio (wireless) to the hand held terminal A-G-247NW
additionally possible.
3.3 Transport
•The device is packed ex factory to suit the transport method previously agreed.
•Always use the original packaging materials when transporting the device.
•Avoid shocks and impacts to the device during the transport.
•During manual handling the human lifting and carrying restrictions must be observed and adhered
to.
3.4 Storage
•The device must be stored in its original packaging in a dry and weather-proof room.
•Avoid exposure to extreme heat and cold.
•Avoid over-long storage periods (we recommend a maximum of one year).
3.5 Disposal / recycling
Disposal must be carried out professionally and in an environmentally friendly way in accordance with
the respective national legal stipulations.
"Separate the materials by type and in an environmentally friendly way.
"If necessary, commission a specialist company with the waste disposal.
Operating Instructions AM-PREMIUM(-W) – model series General description
L-BAL-E095-GB 1618 Index 006 Part.-No.
6/90

4 Mounting the module
Danger due to electric current
•Always read the safety instructions chapter before mounting!
•The terminating device (fan, converter) in which the module is to be installed must be disconnected from
the line voltage for at least 3 minutes before opening!
Attention, electrostatic sensitive devices!
•Damage to electronic components by electrostatic charging must be prevented!
•Touch the protective earth connection in the terminal to equalize the potential immediately before
removing the module from the packing. This applies regardless of whether the device is already
connected to the line.
•Equalize the potential again shortly before installation if the module is not installed immediately after
unpacking.
•After unpacking the module, check for possible transport damage and insert it in the slot provided. Do not
touch the connection!
"ECblue: Mount the module in the housing with the two enclosed screws (permissible tightening torque
M
A
1.3 Nm).
"Fcontrol Basic, Icontrol Basic, PMcontrol: Press the module into the retaining clips.
"Permissible tightening torque of connection terminals M
A
0.24 Nm.
"When an AM-PREMIUM-W module is installed in a fan or converter from ZIEHL-ABEGG, the
enclosed FCC/IC label “EM-W” inside must be stuck to the housing of the terminating device.
Example for mounting the add-on module
Example: Sticking the FCC/IC label “EM-W” inside
onto a fan housing.
Operating Instructions AM-PREMIUM(-W) – model series Mounting the module
L-BAL-E095-GB 1618 Index 006 Part.-No.
7/90

5 Electrical installation
5.1 Safety precautions
Danger due to electric current
•Work on electric components may only be carried out by trained electricians or by persons
instructed in electricity under the supervision of an electrician in accordance with electrical
engineering regulations.
•It is forbidden to carry out work on electrically live parts.
5.2 Analog inputs “E2” / “E3”
The unit has two analog inputs: Analog In 2
| E2 | and Analog In 3 | E3 |
The connection is independent of the programmed operating mode and from the sensor signal
employed.
•When connecting passive temperature sensorsTF.. (KTY81-210) or PT1000 at terminals “E2 / T2”
and/or “E3 / T3” must be paid attention to no polarity.
For a high interference immunity a capacitor must be connected directly to the sensor (1 nF
parallel). With ZIEHL-ABEGG temperature sensors type TF.. (KTY81-210) the capacitor is inte-
grated.
•When connecting aktive sensors at the terminals “E2 / GND” and/or “E3 / GND” attention must be
paid to correct polarity, a 24 V DC power supply is integrated.
•For sensors in two-wire-technology (4 - 20 mA signal), the connection is made on the “E2 / 24 V”
and/or “E3 / 24 V”, “GND” terminal is omitted.
Attention!
Never apply line voltage to analog inputs!
5.3 Analog output (0 - 10 V) “A1”
The analogoutputs 0 - 10 V can be allocated with various functions (
IO Setup: Analog output “A”).
Connection to terminal “A” - “GND” “Analog Out” (I
max
technical data / connection diagram).
It is not permissible to connect outputs of several devices to each other!
5.4 Voltage supply 24 V DC
There is an integrated power supply for external devices, e.g. a sensor. Terminal +24 V, output voltage
tolerance +/- 20%. Max. load current 70 mA.
In case of overload or short circuit (24 V – GND), the external power supply is shut down (multi-fuse).
The device performs a “Reset” and continues operation.
It is not permissible to connect outputs of several devices to each other!
5.5 Connection external terminal type A-G-247NW or AXG-1A(E)
If necessary an external terminal can be connected. This can be e.g. necessary to adapt the pre-
setting during start-up. For information about the current operating condition a terminal can be
permanent attached.
•The connection is made via a 4-strand line at the terminals (D-, D+ and GND).
•e.g., telephone flex e.g. J-Y (St) Y 2x2x0.6 (or similar), maximum line length ca. 250 m.
•Signal “D+” and “D-” (RS 485)
Operating Instructions AM-PREMIUM(-W) – model series Electrical installation
L-BAL-E095-GB 1618 Index 006 Part.-No.
8/90

•Type A-G-247NW, Part.-No. 380090, handheld terminal
11.02.2014
v_prem_modul_link_terminal.vsd
AM-PREMIUM
24V GND E2 T2 GND E3 T3 A1
A-G-247NW
+ 3,3 V
IRDA-RXD
IRDA-TXD
IRDA-SD
A
(D+)
B
(D-)
GND
+ 5 V
A
(D+)
B
(D-)
The voltage supply of the terminal is made by the accumulators inserted there or the plug power supply unit.
•Model AXG-1A, Part-No. 349034 for wall mounting
•Model AXG-1AE, Part-No. 349008 for panel mounting
D-
D+
GND
+24 V
13.07.2007
v_terminal_anschluss.vsd
Voltage supply: Terminal “24 V”, “GND”, (I
max
, for terminal approx. 50 mA)
Operating Instructions AM-PREMIUM(-W) – model series Electrical installation
L-BAL-E095-GB 1618 Index 006 Part.-No.
9/90

5.6 Digital inputs “D1” and “E1 D2”
In the case of use of the module AM-PREMIUM two digital inputs can be programmed. When inserting
the module the analog input “E1” becomes automatically to the second digital input “D2”.
On the printed circuit board of the basic device
D1: contact at Terminals “D1” - “24 V”
D2: contact at Terminals “E1” - “24 V”
Various functions can be allocated to the digital inputs “D1”and “D2” (
IO Setup: Functions summary
of the digital inputs). Activation via floating contacts (a low voltage of ca. 24 V DC is connected).
Attention!
Never apply line voltage to the digital input!
It is not permissible to connect inputs of several devices to each other!
5.7 Communication
5.7.1 Networking via MODBUS-RTU
The device comes equipped with a RS-485 interface for networking via MODBUS. Conntection at: “A
(D+)”, “B (D-)” and “GND”.
The address must be set in the “IO Setup”menu.
Information
A maximum of 64 members can be directly connected to one another, and another 63 members via a
repeater.
5.7.2 RS-485 - network design and interface parameter
Please ensure the correct connection; i.e. "A (D+)" must always be connected to "A (D+)" of the next
devices. The same applies to "B (D-)" .
In addition, a "GND" connection must be established, as dissimilar potential (over 10 V!) will lead to
the destruction of the RS-485 interface (e.g. lightning).
general example for MODBUS device connection
The data line must be connected from one device to the next. No other type of wiring is allowed!
Always use only two wires of one lead (twisted pair) for the connection.
Example for MODBUS connection
Operating Instructions AM-PREMIUM(-W) – model series Electrical installation
L-BAL-E095-GB 1618 Index 006 Part.-No.
10/90

Recommended wire types
1. CAT5 / CAT7 cables
2. J-Y (St) 2x2x0.6 (telephone wire)
3. AWG22 (2x2 twisted pair)
When using telephone flex with four cable cores, we recommend the following allocation:
“A (D+)” red, “B (D-)” black, “GND” white
Information
•Pay attention to sufficient distance from powerlines and motor wires (min. 20 cm).
•Except the data link "A (D+)", "B (D-)" and "GND"- connection may no further cable cores of the data
line be used.
•Max allowed wire length 1000 m (CAT5/7 500 m).
Shielding
The use of shielded cables is normally not demanded but offers high protection against electro-
magnetic interferences, especially high frequencies. However, the effectiveness of the shield depends
on careful installation of the line.
If shielded cables are used, the shield should be placed at “PE” on at least one side (preferably on the
master connection). The occurrence of compensating currents may have to be considered if the shield
is contacted on both sides.
Shield connection correct Shield connection incorrect
Default interface parameter
Baudrate 19200
Bits 8
Parity Even (None, exception of devices agriculture)
Stop bits 1
Handshake none
Information
If any matters are unclear, please contact our V-STE support department for control systems -
ventilation technology. The information sheet "Network structure of MODBUS" R-TIL08_01 contains
detailed information about "MODBUS".
5.7.3 AM-PREMIUM-W Wireless Communication
The type A-G-247NW hand-held terminal can communicate wireless with the type AM-MODBUS-W
communications module (
Operating Instuctions A-G-247NW: AM-PREMIUM App's / Configuration
Online / Wireless).
In a hard-wired system, wireless communication is primarily designed in order to have a second
interface for communicating with the device (e.g., for configuration and diagnostics).
Wireless communication is also used by the MODBUS protocol, so it is necessary to assign an
address. Wireless and hard-wired communications use the same address. The address can be
hard-wire assigned via an RS-485.
For pure, wireless communication, it is recommended to assign the address manually.
•Switch on the device you want to re-address and establish a connection with address 247.
•In “IO Setup”, change the address and then switch this device off again.
•Apply the same procedure to the next device.
Operating Instructions AM-PREMIUM(-W) – model series Electrical installation
L-BAL-E095-GB 1618 Index 006 Part.-No.
11/90

Radio control key (0 - 9999)
Different from RS-485 communication, wireless communication also has a radio control key (0 -
9999). This radio control key is used to encode the messages and ensures that several networks can
be operated in mutually overlapping radio ranges.
For that reason, every wireless MODBUS network should have its own radio control key if there is
another wireless MODBUS network in the vicinity.
The factory setting is
| 9999 | .
A radio control key with the value
| 0 | switches off encoding.
The device must be switched off to save the new radio control key.
The radio control key must be assigned in the same manner as the assignment of the MODBUS
address.
Radio key (Network key)
Menu group “Controller Setup”.
Technical data for wireless Communication:
Radio communication
standard:
IEEE 802.15.4
Frequency: 2.4 GHz (not licensed wireless band, like WLAN, Bluethooth)
16 wireless channels, default wierless channel 0
Communications range: Short-distance radio, within buildings max. 8 m typically 3 - 5m, free field to 25 m,
generally strongly dependent on interferences
Type of communication: Bi-directional, half-duplex
Application protocol: MODBUS-RTU (max. protocol length 125 Bytes and/or 50 register)
Coding: Proprietary through 4-digit number
Network structure: Point - to - point or point - to- mulit point - communication
5.8 Potential at control voltage connections
The control voltage connections (< 50 V) relate to the joint GND potential (Exception: Relay contacts
are potential free). There is a potential separation between the control voltage connections and the
protective earth. It must be ensured that the maximum external voltage at the control voltage
connections cannot exceed 50 V (between “GND” terminals and “PE” protective earth). If necessary, a
connection to the protective earth potential can be established, install bridge between “GND” terminal
and the “PE” connection (terminal for screening).
Operating Instructions AM-PREMIUM(-W) – model series Electrical installation
L-BAL-E095-GB 1618 Index 006 Part.-No.
12/90

6 Operating by terminal
6.1 Menu operation
Display after turning on the voltage supply.
description for menu language English “GB” (delivery status).
Switch over between “Start” and *Actual value with Escape
| Esc | .
Example for mode 1.01 (speed controller).
*actual value depending device type:
- "Speed" / rpm,- "Frequency" / Hz, - "Fanlevel" / %
By pushing the P key one reaches the menu item “START”. P↓ ↑ ESC
▲ ▼One moves up and down within the menu group using the arrow keys.
In the menu point “Language” display language can be selected.
One returns to the menu group “Start” using the ESC (▼ + ▲) shortcut keys.
6.2 Menu structure
PIN 0010
STOP
← ← ← ← User Service → → → →
Start
▼
▲Info
▼
▲Setting
▼
▲Events
▼
▲Base setup
P↓ ↑ ESC P↓ ↑ ESC P↓ ↑ ESC P↓ ↑ ESC P↓ ↑ ESC
PIN input Frequency Set Intern1 Motor fault Mode
▲ ▼ ▲ ▼ ▲ ▼ ▲ ▼ ▲ ▼
Language Set external1 Set Intern2 E1 Analog In
Menu dependent on device type
Operating Instructions AM-PREMIUM(-W) – model series Operating by terminal
L-BAL-E095-GB 1618 Index 006 Part.-No.
13/90

Selection of the menu group (e.g. Base setup) to the right through the ▼-key, to the left through the
▼-key.
You can go to the menu items in the menu groups (e.g. mode of operation) by using the P key. Use
the arrow keys to move up and down within the menu group.
The menu groups consist of one area for the user (user menu) and one area for installation (service).
The service area can be protected against unauthorized access by using a PIN.
In order to simplify the initial start-up operation, the service level is enabled at first (i.e., not protected
by the PIN 0010 (
see Controller Setup, PIN protection OFF). If PIN protection is activated (ON),
the service menu remains enabled after input of PIN 0010 as long as one is pressing keys. If no keys
are pressed for ca. 15 minutes, the PIN is automatically erased, i.e. the service level is blocked.
To make adjustments, press the P key after selecting the menu item. If the previously set value starts
to ash, it can be adjusted with the ▼ + ▲ keys and then saved with the P key. To exit the menu
without making any changes, use the “Esc” short-key, i.e., the originally set values remain.
Information
After installation of the device has been carried out, PIN protection should be activated ( Controller
Setup)!
6.3 Example for programming mode 2.01 in “Base setup”
1 2 3 4567
Mode
P
Mode
▲
Mode
P
Mode
Operating Instructions AM-PREMIUM(-W) – model series Operating by terminal
L-BAL-E095-GB 1618 Index 006 Part.-No.
14/90

7 Base setup
7.1 Select operation mode
Information
Simple installation is possible through the selection of the preprogrammed mode of operation.
This determines the basic function of the device; factory setting 1.01 speed controller
(activation via 0 - 10 V signal). The controller configuration is automatically carried out during
selection of the application related mode of operation. The factory presets in accordance with
the mode of operation are based on many years of experience, which is suitable for many
applications. Under special circumstances, these can be individually adapted (
Controller
Setup: “Controller Configuration”).
The purpose of the device is to reach and maintain the target values set. To accomplish this, the
measured actual value (sensor value) is compared with the adjusted target value, and the controlled
value (modulation) is deduced from this.
Mode Signal or Sensor
(input) Function
1.01 Signal 0 - 10 V Speed controller, two step operation (factory setting)
2.01 Sensor KTY81-210 / PT1000 (E2) Temperature control airconditioning and refrigeration.
(preset set-point 20.0 °C, P-band 5.0 K)
2.02 Sensor KTY81-210 / PT1000 (E3) Temperature control depending on outdoor temperature
(preset set-point 5.0 °C, - P-band 20.0 K)
2.03 Sensor KTY81-210 / PT1000 (E2) Temperature control with additional functions (shutter and heating)
2.04 1x Sensor KTY81-210 / PT1000 (E2)
1x Sensor KTY81-210 / PT1000 (E3)
Temperature control with two sensors, comparison or average
2.05 1x Sensor KTY81-210 / PT1000 (E2)
1x Sensor KTY81-210 / PT1000 (E3)
Temperature control with two sensors differential temperature
3.01 Sensor MBG.. (E2) Pressure control condensers (refrigeration)
3.02 Sensor MBG..(E2) Pressure control for condensers with input for refrigerant
3.03 1x Sensor MBG..(E2)
1x Sensor MBG..(E3)
Pressure control for two circuit condensers
3.04 1x Sensor MBG..(E2)
1x Sensor MBG..(E3)
Pressure control for two circuit condensers with input for refrigerant
4.01 Sensor DSG.. / MPG.. (E2) Pressure control for ventilation systems
4.02 1x Sensor DSG.. / MPG.. (E2)
1x Sensor KTY81-210 / PT1000 (E3)
Pressure control depending on outdoor temperature
4.03
1x Sensor DSG.. / MPG.. (E2)
1x BUS RS 485
Pressure control depending on outdoor temperature, MODBUS for out-
door temperature and remote control by central operating device type
AXE-200AX
5.01 Sensor DSG.. / MPG.. (E2) Volume control (constant) for ventilation systems
5.02 1x Sensor DSG.. / MPG.. (E2)
1x Sensor KTY81-210 / PT1000 (E3)
Volume control with setpoint depending on outdoor temperature
6.01 Sensor MAL..(E2) Air velocity control e.g. clean room
Operating Instructions AM-PREMIUM(-W) – model series Base setup
L-BAL-E095-GB 1618 Index 006 Part.-No.
15/90

Mode and Signal to E1, E3
07.05.2012
v_e2_e3_signal_sensor_pwm.vsd
A1 E2 GND
0-10 V
10 k
0 - 10 V TF..
24V E2 GND
DSG 0 - 10 V
YE
DSG.. / MPG..
(0 - 10 V)
WHBN
24V E2 GND
MAL 0 - 10 V
3
MAL1/10
(0 - 10 V)
21
31
BN GN
MBG..-I
24V E2
MBG..
(4 - 20 mA)
E2 T2
KTY81-210
PT 1000
GND
1.01 2.01 2.03 .. 3.01 3.02 +6.014.01 5.01 +
2.04 2.05
+
TF..
E3 T3
TF..
KTY81-210
PT 1000
Rext
10 V PWM
f = 1..10 kHz @ Rext = 1 kohm
f = 1 kHz @ Rext = 10 kohm
t = 0...100 %
GND E2 A1
31
BN GN
MBG..-I
24V E3
MBG..
(4 - 20 mA)
GND
3.03 3.04
+4.02 5.02
+
TF..
E3 T3
TF..
KTY81-210
PT 1000
4.03
D+GND D-
Data
RS-485
7.2 External Setpoint / External speed setting in manual operation
External setpoint setting or external manual operation are possible using a 0 - 10 V (0 - 20 mA, 4 - 20 mA) signal at the “E3” and
“GND” terminals. Configure “E3” in Base setup. For potentiometers, program Analog Out 1 (terminal “A1”) to the function
| 1A |
“+10 V” (as factory setting
IO Setup).
E3 Analog In factory setting 0 - 10 V
A1 E3 GND
Signal 0-10 V
10 k
16.01.2012
v_extern_poti_e3.vsd
External Setpoint via external signal instead of “Setpoint 1”. The “external Setpoint” function must be activated in base setup
| 1E | for “E3 function”. The active external Setpoint value is displayed in the “info” menu group.
External speed setting in manual operation. The “external manual operation” function must be activated in the basic settings
| 2E | for “E3 function”. Switchover between settings on the device and external manual operation via the digital input ( IO
Setup: “Control / manual operation”
| 7D | ).
Operating Instructions AM-PREMIUM(-W) – model series Base setup
L-BAL-E095-GB 1618 Index 006 Part.-No.
16/90

8 Start-up
8.1 Prerequisites for commissioning
Attention!
1. You must mount and connect the device in accordance with the operating instructions.
2. Double check that all connections are correct.
3. Make sure that no persons or objects are in the fan's hazardous area.
8.2 Procedure for commissioning
Sequence Setting
1If necessary, set the menu language in Menu group “Start”.
(Factory setting Englisch: “Language GB”)
2
Set the operating mode in the Base setup menu group (factory settings 1.01 speed controllers).
Attention!
When saving the operating mode, the respective preset factory operating-mode setting is loaded. That means,
the settings you have made, e.g., in “Motor Setup” are lost. An exception: the menu language setting remains
preserved.
8.3 Menu Mode 1.01
Example for ECblue
Start Info Setting Events Base
setup
Controller
Setup IO Setup Limits Motor
Setup Diagnostic
- - - -
PIN input
0 rpm
Speed
200 rpm
Set Intern1
-0-
Factory
sett.
1.01
Mode
OFF
PIN Protec-
tion
| 1A |
A Function
OFF
Controller
function
20 sec
Rampup
time
OTC
00012:56:-
15
GB Lan-
guage
0.0 A
Motor cur-
rent
- - - - -
Set Intern2
-1-
Sensor 1
0 - 10 V
E2 Analog
In
OFF
Set protec-
tion
0.0 V
A min.
- - - - -
Level min
20 sec
Rampdown
time
OTM
00010:56:-
11
OFF
Reset
0 rpm
Set exter-
nal1
0 rpm
Min. Speed
-3-
ext. Fault
OFF
E3 Func-
tion
OFF
Save User
Setup
10.0 V
A max.
- - - - -
Level max.
OFF
Suppres-
sion1
585 V
DC-Voltage
1.01
Mode
1800 rpm
Max.
Speed
- - - - -
E3 Analog
In
- - - - -
Limit
OFF
A Inverting
- - - - -
Level Delay
- - - - -
Range1 mi-
n.
244 V
Line volt-
age
4.00
ECblue
Premium
ON
Set exter-
nal1
- - - - -
Group 2
ON value
OFF
D1 Func-
tion
OFF
Lmt E2
Function
- - - - -
Range1
max.
29.5 °C
Heatsink
1.01
Basic Ver-
sion
- - - - -
nmin at
Group2
- - - - - -
D1 Invert-
ing
- - - - -
Lmt E2 min
OFF
Suppres-
sion1
29.5 °C
Capacitor
Menu dependent on device type
Operating Instructions AM-PREMIUM(-W) – model series Start-up
L-BAL-E095-GB 1618 Index 006 Part.-No.
17/90

9 Programming
9.1 Speed controller 1.01
9.1.1 Base setup 1.01
Base setup
Base setup
Mode
Mode
Factory setting Mode: 1.01
E2 Analog In
E2 Analog In
Selection: 0 - 10 V, 0 - 20 mA, 4 - 20 mA, KTY, PT1000 (Inverting
IO Setup)
Factory setting: 0 - 10 V
E3 Function
E3 Function (only for special applications)
•Analog input 2 “E3 function”factory set at “OFF”.
•For operation with a second signal and switch over via floating contact set function
for “E3” to
| 1E | ( IO Setup: function | 4D | ).
•For operation with a second signal and automatic control at the higher level. Set “E3”
Function to
| 4E | .
•Measurement value function
| 7E | e.g. for limit indication, display in Info menu “E3
Actual”.
E3 Analog In
E3 Analog In
As long as no allocation has been carried out display: | - - - - - |
Selection: 0 - 10 V, 0 - 20 mA, 4 - 20 mA, KTY, PT1000 (Inverting IO Setup)
Factory setting: 0 - 10 V
9.1.2 Setting for operation 1.01
ECblue
Setting
Setting
Set Intern1
Set Intern1
Setting range manual speed setting: 0 rpm... “Max. Speed”
Factory setting: 200 rpm
Set Intern2
Set Intern2
Setting “Set Intern 2” e.g. reduced value for night operation.
Switch over intern 1/2 by external contact (as long as no allocation is carried out:
Display:
| - - - - - | IO Setup).
Min. Speed
Min. Speed
Setting range: 0 rpm... “Max. Speed”
Factory setting: 0 rpm
Max. Speed
Max. Speed
Setting range: Rated speed ...0 rpm (takes priority over setting “Min. Speed”)
Factory setting: Rated speed
Set external1
Set external1
“ON” (factory setting) speed setting by external Signal
“OFF” Setting “Set Intern1”
Operating Instructions AM-PREMIUM(-W) – model series Programming
L-BAL-E095-GB 1618 Index 006 Part.-No.
18/90

Diagram setting signal and output voltage (Idealized principle diagram)
nM
50 %
100 %
0 1 2 3 4 5 6 7 8 9 10
10 9 8 7 6 5 4 3 2 1 0
0 2 4 6 8 10 12 14 16 18 20
20 18 16 14 12 10 8 6 4 2 0
4 5,6 7,2 8,8 10,4 12 13,6 15,2 16,8 18,4 20
20 18,4 16,8 15,2 13,6 12 10,4 8,8 7,2 5,6 4
0 – 10 V
10 – 0 V
0 – 20 mA
20 – 0 mA
4 – 20 mA
20 – 4 mA
Min.
Min. 0 % Max. = 100 %
Min. 35 % Max. = 85 %
09.05.2007
v_nmotor_101.vsd
Si
100 % Rated speed
nM Motor speed
Si Signal
Icontrol / Fcontrol Basic
Setting
Setting
Set Intern1
Set Intern1
Setting range manual speed setting: “Min. Speed” - “Max. Speed”
Factory setting: 50.0 Hz (
Setting “Max. Speed”)
Set Intern2
Set Intern2
Setting “Set Intern2” e.g. reduced value for night operation.
Switch over intern 1/2 by external contact (as long as no allocation is carried out:
Display:
| - - - - - | IO Setup).
Min. Speed
Min. Speed (basic speed only when needed)
Setting range: 0... “Max. Frequency” (
Motor Setup).
Factory setting: 0.0 Hz
Active in every control mode, priority by “Max. speed”.
Max. Speed
Max. Speed (speed limitation only when needed)
Setting range: “Max. Frequency” (
Motor Setup)... “Min. Speed ”
Factory setting: 50.0 Hz
Active in every control mode!
Settings by “Max. frequency” are possible but are not made!
Set external1
Set external1
“ON” (factory setting) speed setting by external Signal
“OFF” Setting “Set Intern1”
Operating Instructions AM-PREMIUM(-W) – model series Programming
L-BAL-E095-GB 1618 Index 006 Part.-No.
19/90

Diagram setting signal and output frequency
Fout [Hz]
08.05.2012
v_fxdm_setsig_min_max.vsd
1 2 34 5 67 8 910
Analog In 1
40
35
30
25
20
15
10
5
2 4 68 10 12 14 16 18 20
0...10 V
0...20 mA
10 20 30 40 50 60 70 80 90 100 0...100 % PWM
0
0
0
45
50
n-min OFF n-max. = 50 Hz
n-min 20 Hz n-max. = 45 Hz
n-min 10 Hz n-max. = 50 Hz
Foff = 5 Hz
Fon = 6 Hz
Fout: Output frequency
Analog In: Speed setting signal
n-min: Min. Speed
n-max: Max. Speed
Foff: Shutdown Freq.
Fon: Switch on Freq.
9.2 Temperature control 2.01 ... 2.05
9.2.1 Basic setting 2.01 ... 2.05
Base setup
Base setup
Mode
Mode
Mode selection e.g. 2.01
E2 Analog In
E2 Analog In
In all group 2 operating modes (2.01, 2.02, 2.03, ....)
“E2 Analog In” factory set to “KTY” (sensors type TF..) at terminals “E2” and “T2”
(measuring range: -50.0...+140 °C).
Alternative selection sensor
•PT1000 to Terminals “E2” and “T2” (Measuring range -50.0...+140 °C)
•MTG-120V active sensor with 0 - 10 V output at terminals “E2” and “GND”
(measuring range: -10...+120 °C)
Alternative selection signal at terminals “E2” and “GND”: 0 - 10 V, 0 - 20 mA, 4 - 20 mA.
The sensor measurement range must be entered in order to display the actual value
correctly.
Example with a 0 - 10 V sensor and 0 - 100 °C measurement range:
E2 Analog In 0 - 10 V, E2 Min. 0.0 °C, E2 Max. 100.0 °C, E2 Decimally 1, E2
Unit °C
E2 Offset
E2 Offset
Sensor calibration with calibrated comparison device
Operating Instructions AM-PREMIUM(-W) – model series Programming
L-BAL-E095-GB 1618 Index 006 Part.-No.
20/90