ZIEHL-ABEGG FE2owlet-ECQ User manual

FE2owlet-ECQ
Motor size U
EC-fans with top efficiency
Assembly instructions
Keep for reference!
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
english

Content
1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Structure of the assembly instructions . . . . . . . . . . . . . . . . . . . . 4
1.3 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Improper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Explanations of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5 Requirements placed on the personnel / due diligence . . . . . . . 7
2.6 Work on the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.7 Modifications / interventions in the device . . . . . . . . . . . . . . . . . 7
2.8 Operator’s obligation of diligence . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9 Employment of external personnel . . . . . . . . . . . . . . . . . . . . . . . 8
3 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Application operational area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Motor protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Note on the ErP directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5 Transport, storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.6 Disposal / recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Connection cable & junction box . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Dimensions motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 Mounting fans design A and E . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Connection of the motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Prerequisites for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . 15
Assembly instructions FE2owlet-ECQ
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
2/24

6 Diagnostics / Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7 Service work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1 Maintenance/servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.2 EC Declaration of Incorporation . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.3 UKCA Declaration of Incorporation . . . . . . . . . . . . . . . . . . . . . . . 22
8.4 Manufacturer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.5 Service address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Assembly instructions FE2owlet-ECQ
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
3/24

1 General notes
Compliance with the following specifications also serves to ensure product safety.
Should the specified information, in particular with regard to general safety, transporta-
tion, storage, assembly, operating conditions, commissioning, service, maintenance,
cleaning and disposal/recycling not be observed, safe operation of the product may not
be guaranteed and can potentially pose a risk of death or injury to users and/or third
parties.
For this reason, deviations from the specifications below can lead to the loss of legal
materials defect liability as well as to liability of the buyer for the product rendered unsafe
by deviation from the specifications.
1.1 Validity
This document is valid for ECblue-axial fans of motor size U (060).
The used motor size is recognisable from the type designation (see rating plate).
e.g. type: FN023-4QA.UA.V5P3
In the case of fans with the quality mark (see rating plate), please note the related
specifications depending on the application location!
1.2 Structure of the assembly instructions
Before installation and start-up, read this assembly instructions carefully to ensure
correct use!
We emphasize that these assembly instructions apply to specific units only, and are in
no way valid for the complete system!
Use these assembly instructions to work safely with and on the device. They contain
safety instructions that must be complied with as well as information that is required for
failure-free operation of the device.
Keep these assembly instructions together with the device. It must be ensured that all
persons that are to work on the device can refer to the assembly instructions at any time.
Keep the assembly instructions for continued use. They must be passed-on to all
successive owners, users and final customers.
1.3 Target group
The assembly instructions address persons entrusted with planning, installation, com-
missioning and maintenance and servicing and who have the corresponding qualifica-
tions and skills for their job.
1.4 Exclusion of liability
Concurrence between the contents of these assembly instructions and the described
hardware and software in the device has been examined. It is still possible that non-
compliances exist; no guarantee is assumed for complete conformity. To allow for future
developments, construction methods and technical data given are subject to alteration.
We do not accept any liability for possible errors or omissions in the information con-
tained in data, illustrations or drawings provided.
Assembly instructions FE2owlet-ECQ General notes
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
4/24

ZIEHL-ABEGG SE is not liable for damage due to misuse, improper use or as a
consequence of unauthorized repairs or modifications.
1.5 Copyright
These assembly instructions contain copyright protected information. The assembly
instructions may be neither completely nor partially photocopied, reproduced, translated
or put on data medium without previous explicit consent from ZIEHL-ABEGG SE. In-
fringements are liable for damages. All rights reserved, including those that arise through
patent issue or registration on a utility model.
2 Safety instructions
2.1 Intended use
Attention!
•The fans are only intended for the conveyance of air or mixtures similar to air.
•Any other use above and beyond this is considered not for the intended purpose
unless agreed otherwise by contract. The manufacturer will not be liable for any
damage resulting from this. The individual or company using it bears the sole risk.
•Built-in fans with VDE approval (see rating plate) are designed to be installed inside
devices and are not suitable for the direct mains connection.
•Reading these document and complying with all contained instructions -especially the
safety notifications contained therein -are considered part of intended use.
•To consider is also the documentation of attached components.
2.2 Improper use
Improper use / reasonably foreseeable misuse
•Conveyance of aggressive and explosive gaseous media.
•Use in areas at risk of explosion for conveying gas, mist, vapours or mixtures of the
above.
•Transfer of solids or solids content in the transfer medium.
•Operation with iced up impellers.
•Conveyance of abrasive or adhesive media.
•Conveyance of liquid media.
•Operation of plug fans outside devices.
•Connect built-in fans to open flue pipes of gas and other firing devices.
•Use of the fan and add-on parts (e.g. guard grille) as a resting surface or climbing aid.
–Fans are not designed for walking on even with an additive diffusor attachment
(retrofit kit)! Do not climb onto fans without suitable aids.
•Unauthorised constructional modifications to the fan.
•Operation of the fan as a safety component or for the performance of safety-relevant
functions in the sense of EN ISO 13849-1.
•Blocking or braking of the fan by inserting objects.
•Use with direct contact with foodstuffs or cosmetic and pharmaceutical products.
Assembly instructions FE2owlet-ECQ Safety instructions
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
5/24

•Use of the fan as an independent household appliance.
•Use as a fire gas or smoke extraction fan (special application according to
DIN EN 12101-3).
•Use with vibration loading by customer device. Resonant operation and operation
with severe vibrations or oscillation.
•Loosening of fan blade, impeller, motor suspension and balancing weight.
•All applications not listed in the intended use.
Attention!
Not the manufacturer, rather the operator of the device is liable for any personal harm or
material damage arising from non-intended use.
2.3 Explanations of symbols
Safety instructions are highlighted with warning triangles and are depicted
according to the degree of hazard as follows.
Attention!
General hazardous area. Death or severe injury or significant property damage can
occur if the corresponding precautions are not taken!
Danger due to electric current
Danger by dangerous, electric voltage! Death or severe injury can occur if the
corresponding precautions are not taken!
Info
Important additional information and advice for user.
2.4 Product safety
The device conforms to the state of the art at the time of delivery and is fundamentally
considered to be reliable. The device and its accessories must only be used in a flawless
condition and installed and operated in compliance with the assembly instructions and/or
operating instructions. Operating outside the device's technical specifications (see name
plate and attachment / technical data) can lead to a defect in the device and additional
damage!
Info
A separate fault and performance monitoring-system with an alarm signal function is
necessary in order to prevent personal injuries and material damages during malfunc-
tions and in case the device fails. Substitute operation must be taken into consideration!
The design and installation of the system must comply with local regulations and
directives.
Assembly instructions FE2owlet-ECQ Safety instructions
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
6/24

2.5 Requirements placed on the personnel / due diligence
Persons entrusted with the planning, installation, commissioning and maintenance and
servicing in connection with the frequency inverter must have the corresponding qual-
ifications and skills for these jobs.
In addition, they must be knowledgeable about the safety regulations, directives, rules
for the prevention of accidents and the corresponding national as well as regional and in-
house regulations. Personnel to be trained or instructed and apprentices are only
permitted to work on the device under the supervision of an experienced person. This
also applies to personnel undergoing general training. Comply with the legal minimum
age.
2.6 Work on the device
Info
Mounting, electrical connection, and start-up operation may only be carried out by an
electrical specialist in accordance with electrotechnical regulations (e.g. EN 50110 or
EN 60204)!
Danger due to electric current
•It is generally forbidden to carry out work on electrical live parts!
•The 5 electrical safety rules must be observed!
•The safe isolation from the supply must be checked using a two-pole voltage
detector.
•Opening of motor is prohibited. Loosening the screws will void the warranty!
•Any faults detected in the electric system/modules/operating equipment must be
corrected immediately. If these faults are not corrected, the device/system is
potentially very dangerous. The device/system must therefore not be operated when it
is faulty.
•Fuses must always be only replaced; never repaired or bridged. The specifications for
the maximum series fuse must always be adhered to (
Technical data). Only fuses
cited in the electrical circuit diagram may be used.
Attention, automatic restart!
•The motor may switch on and off automatically for functional reasons.
•Automatically restart after a power failure or mains disconnection!
•Wait until the motor has stopped before approaching.
Danger of being sucked in!
Do not wear loose or hanging clothing, jewellery, etc., tie together long hair and cover it.
2.7 Modifications / interventions in the device
Attention!
For reasons of safety, no unauthorized interventions or modifications may be made on
the device. All planned modifications must be authorized by the manufacturer in writing.
Assembly instructions FE2owlet-ECQ Safety instructions
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
7/24

Use only genuine spare parts / genuine wearing parts / genuine accessories from
ZIEHL-ABEGG.These parts were specifically designed for the device. There is no
guarantee that parts from non-original sources are designed and manufactured in
correspondence with load and safety requirements.
Parts and optional equipment not supplied by ZIEHL-ABEGG are not approved by
ZIEHL-ABEGG for use.
2.8 Operator’s obligation of diligence
•The contractor or owner must also ensure that the electric systems and equipment
are operated and maintained in accordance with electro-technical regulations.
•The owner is obliged to ensure that the device is operated in perfect working order
only.
•The device may only be used as intended.
•You must periodically examine the safety equipment for their properly functioning
condition.
•The assembly instructions and/or operating instructions are always readily available
at the location where the device is being used, are complete and are in legible
condition.
•These persons are regularly instructed in all applicable questions regarding occupa-
tional safety and environmental protection and are knowledgeable regarding the
assembly instructions and/or operating instructions and, especially, are familiar with
the safety instructions contained therein.
•All safety and warning notices attached to the device are never removed and remain
legible.
2.9 Employment of external personnel
Maintenance and service work are frequently carried out by external employees who
often do not recognize the specific situations and the thus resulting dangers.These
persons must be comprehensively informed about the hazards in their area of activity.
You must monitor their working methods in order to intervene in good time if necessary.
Assembly instructions FE2owlet-ECQ Safety instructions
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
8/24

3 Product overview
3.1 Application operational area
The fans / motors are not ready-for-use products, but conceived as components for
ventilation systems (type designation see rating plate).
The fans may not be operated until they are installed in line with their intended use. The
supplied and certified guard grille of ZIEHL-ABEGG SE fans is designed in accordance
with DIN EN ISO 13857 Table 4 (from the age of 14 up). In the event of deviations,
further structural protective measures must be taken for safe operation.
Attention!
If the motor/fan is used in applications where a ignitable atmosphere can form in the
event of a fault, e.g. due to leakage, the user must assess the risks of ignition and take
appropriate precautions to prevent ignition.
3.2 Functional description
ECQ motors from ZIEHL-ABEGG are highly efficient, electronically commuted motors
(EC) with an integrated controller. They are designed exclusively for driving axial fans.
The motors are designed for continuous operation (S1-operation) and are thermally
protected.
Depending on version motors with a fixed speed or motors with three speeds (
rating
plate).
Motors with three speeds
•Three pre-programmed speeds are possible (
rating plate) which are activated
depending on the connection of the additional control input at “L1” or “N”.
•With the “Motor Programmer” (accessory) and a PC with the appropriate software,
individual speeds and the rotation direction can be programmed.
This assembly manual describes ECQ fans in different models and sizes. Connection,
structure and technical details depend partly on the fan size.
3.3 Motor protection
The motor has devices to protect it from overloading, these include protection in case of
blocked rotor and overload protection with running motor.
On exceeding the maximum permissible operating temperature, this can lead to stopping
of the motor and can cause permanent damage!
3.4 Note on the ErP directive
ZIEHL-ABEGG SE wishes to point out that, based on the directive (EU) no. 327/2011 of
the Commission of 30th of March 2011 for enforcing directive 2009/125/EC (hereinafter
referred to as ErP directive), the operational area of certain fans within the EU is bound
by certain prerequisites.
The fan may only be used within the EU when it meets the requirements of the ErP
directive.
Assembly instructions FE2owlet-ECQ Product overview
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
9/24

If the said fan does not have a CE mark (cf. especially the rating plate), use of this
product within the EU is not admissible.
All ErP-relevant information comprises measurements which are determined using a
standardised measurement set-up. More details can be obtained from the manufacturer.
Further information about the ErP directive (Energy related Products-Directive) can be
found on www.ziehl-abegg.de search key: "ErP".
3.5 Transport, storage
Attention!
•Use the original packaging materials when transporting the device.
•Do not transport the fan by the connecting cable!
•Avoid shocks and impacts to the device during the transport.
•Avoid extreme humidity, heat or exposure to cold (
Technical Data).
•Pay attention to possible damage of the packaging or the equipment.
•Store the fan / motor in the original packaging in a dry area protected from the weather
and protect it from dirt and weather until final installation.
•Protect the motor against ultraviolet radiation.
•Avoid prolonged storage; we recommend a maximum of one year (consult the
manufacturer before starting if stored for longer).
•Inspect the bearing for proper operation prior to installation.
3.6 Disposal / recycling
Disposal must be carried out professionally and in an environmentally friendly way in
accordance with the respective national legal stipulations.
"Separate the materials by type and in an environmentally-friendly way.
"If necessary, commission a specialist company with the waste disposal.
Assembly instructions FE2owlet-ECQ Product overview
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
10/24

4 Mounting
4.1 General notes
Attention!
•Check the fan for damage, e.g. cracks, dents or damage to the electric cables, before
assembly. Start-up is not allowed in the case of transport damage!
•Mounting is only to be undertaken by trained service personnel. The system
manufacturer or the machine builder and/or the user is responsible that the inherent
installation and security information are harmonized with the valid standard and
guidelines (EN ISO12100 / 13857).
•Do not allow drilling chips, screws and other foreign bodies to reach the device
interior!
•Prior to installing the fan, it is to be checked whether the safety zone as per EN ISO
13857 and in household appliances as per EN 60335 are met. If the installation height
(danger zone) above the reference level is greater than or equal to 2700 mm and is
not reduced by auxiliary means such as chairs, ladders, work platforms or bases on
vehicles, a guard grille against accidental contact is not necessary at the fan.
•If the fan is located in danger zone, then the manufacturer or operator shall ensure
that hazards shall be prevented by appropriare protective constuctions which meet
the requirements to EN ISO 13857.
•The custom designs must suit the prevailing conditions.
•Tighten the fastenings with the specified torques.
•Any use below -10 °C is dependent on not being subjected to unusual, sudden or
mechanical loads or stresses on the material (min. ambient temperature
Technical
data).
•Corrosion is possible at the cutting edges on sendzimir galvanised parts.
•The chemical after-treatment of the nozzle can lead to visible residues. These do not
have any technical effect however.
4.2 Connection cable & junction box
Info
In demanding environments (wet rooms, outdoor installation), connection cables must
have water draining pipe elbows. If using a junction box, install this lower than the motor
to ensure that water cannot penetrate through to the controller housing from the
connection cables.
Assembly instructions FE2owlet-ECQ Mounting
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
11/24

4.3 Dimensions motor
03060-NN04
17.11.2021
Info
The 7 holes in the motor's plastic housing (for self-tapping screws Ø 4.2) are designed for
one-time use.
4.4 Mounting fans design A and E
To attach the fan unit, use screws with a property class of 4.8 as per EN ISO 4014 and
provide with suitable thread lockers.
Permissible tightening torques M
A
Fastening element Central screw connec-
tion
Fastening element for
add-on parts Motor fastening
Material Steel Steel Plastic
Motor size U
Thread size M4
Property class 4.8 4.8
Friction value µges 0.12
Tightening torque 1.7 Nm 1.7 Nm 1.7 Nm
When using other connection elements with different friction values or property classes,
different tightening torques may be necessary.
Assembly instructions FE2owlet-ECQ Mounting
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
12/24

Info
•Every screwing case is different. The tightening torque adapted to it must be
determined by the appropriate screw tests.
•Avoid structural damage or stress with installation. Make sure the surface is flat and
even.
•Secure fan connection cable with cable fasteners on guard grille or support struts.
L-KL-3395
Fans design E
A minimum head gap “A” of
3.5 mm in all installation positions,
but especially in installation
position H (horizontal motor shaft),
is necessary. Installation surfaces
must be level.
4.5 Connection of the motor
Danger due to electric current
•The mains voltage must comply with the EN 50160 quality characteristics and the
defined standard voltages in IEC 60038!
•Connect the motor only to electrical circuits that can be disconnected with an all-pole
isolating switch.
•The device owner is responsible for the EMC of the entire plant according to the
locally applicable standards.
Connection diagram for motors with one speed
KT00047B
18.11.2015
M
1 ~
ECQ
BU
rpm 1
BN
N
L1
N, L1 Line voltage see rating plate
BN brown
BU blue
Assembly instructions FE2owlet-ECQ Mounting
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
13/24

Connection diagram for motors with three speeds
KT00047A
14.04.2016
M
1 ~
ECQ
BU
rpm 1
BN
BK
C
N
L1
M
1 ~
ECQ
BU
BN
BK
C
N
L1
M
1 ~
ECQ
BU
BN
BK
C
N
L1
rpm 2
rpm 3
N, L1 Line voltage rating plate
C Control input speed
BK black
BN brown
BU blue
rpm 3 Speed step 3
rpm 2 Speed step 2
rpm 1 Speed step 1
If the black wire is connected with the brown
wire, the motor runs at speed step 3
If the black wire is connected with the blue wire,
the motor runs at speed step 2
If the black wire is not connected, the motor runs
at speed step 1
Danger due to electric current
A dangerous voltage (maximum line voltage is applied at the black connecting wire
(speed control input) when it is not used (speed step 1). Therefore this wire must be
connected to a terminal for insulation.
Assembly instructions FE2owlet-ECQ Mounting
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
14/24

5 Commissioning
5.1 Prerequisites for commissioning
Attention!
•During commissioning, unexpected and hazardous conditions can arise in the entire
installation due to defective adjustments, defective components or incorrect electrical
connections. Remove all persons and objects from the hazardous area.
•Do not start the fan until all safety instructions (DIN EN 50110, IEC 364) have been
checked, the fan is out of range (DIN EN ISO 13857) and danger can be ruled out.
•A-rated sound power levels of over 80 dB(A) are possible, see product catalogue.
Before first-time start-up, check the following:
1. Installation and electrical connection have been properly completed?
2. Has any leftover installation material and other foreign material been removed from
the fan area?
3. That safety devices -if necessary- are mounted (EN ISO 13857)?
4. The impeller is out of reach?
5. Are the drain holes (as far as available) open or respectively closed according to
the suitable installation position?
6. Connection data complies with the specifications on the rating plate?
During start-up check the following:
1. Check the rotat. direction (see the rotat. direction arrow on the fan blade, impeller
base plate or intake-side support plate).
2. Check for quiet, low vibration operation. Strong vibrations due to erratic operation
(unbalanced), e.g. caused by transportation damage or improper use, can lead to
failure.
3. Check the system for resonances. If they lead to unacceptably high vibrations on
the fan, the system must not be started up.
4. Fans from ZIEHL-ABEGG SE are delivered balanced in accordance with
DIN ISO 21940-11 for the appropriate fan category in accordance with ISO 14694.
Check the fan for mechanical vibrations after installation. If the limit values of the
corresponding fan category are exceeded in start-up, you must have the motor/im-
peller unit checked by an expert and rebalanced if necessary before continuous
operation is permitted.
Assembly instructions FE2owlet-ECQ Commissioning
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
15/24

6 Diagnostics / Faults
6.1 Trouble shooting
Type of error Possible cause Remedial measures
Fan does not
run (anymore)
Mains voltage failure
Failure of a phase
Under - or overvoltage
Check mains voltage
Coil closure Replace fan
Thermal motor protection
has triggered (motor is over-
heated)
Check for free air passages; remove foreign bodies if nec-
essary
See “Impeller blocked or dirty”
Check supply air temperature
Check voltage
Impeller blocked or dirty - Disconnect the motor from the power supply and secure it
against switching back on
- Check safe isolation from supply
- Remove protective grille
- Remove foreign bodies or dirt
- Reinstall protective grille
- proceed as described in the Commissioning chapter
Fan does not
start
Air stream wrong direction
(Motor turns in wrong direc-
tion at high speed)
Check air stream
see “Fan does not run”
“Fan turns too
slowly”
Impeller / blade drags /
scrapes
When indicated clear foreign bodies / dirt from the fan
Check for free air passages; remove foreign bodies if nec-
essary
See “Impeller blocked or dirty”
air flow too low “Fan turns too slowly”see "Fan turns too slowly"
Airways blocked Check for free air passages (supply/exhaust air flaps, fil-
ters)
See “Impeller blocked or dirty”
Pressure loss different to
projection
Check fan selection
Vibrations Imbalance Check blades for damage, soiling or ice (see "Impeller
blocked or dirty")
unusual noises Impeller / blade drags /
scrapes
When indicated clear foreign bodies / dirt from the fan (see
"Impeller blocked or dirty")
Operation beyond tear-off
point
Check for free air passages (supply/exhaust air flaps, fil-
ters)
Assembly instructions FE2owlet-ECQ Diagnostics / Faults
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
16/24

7 Service work
7.1 Maintenance/servicing
Attention!
•Allow maintenance work to be carried out by trained specialists only.
•Any faults detected in the electric system/modules/operating equipment must be
corrected immediately. If these faults are not corrected, the device/system is
potentially very dangerous. The device/system must therefore not be operated when it
is faulty.
•Wear safety clothing / shoes and cut-resistant safety gloves when handling!
•Please observe the safety regulations and the worker´s protection rules by all
maintenance and service work (EN 50 110, IEC 364).
•Before working on the fan, this must be disconnected from the power supply
and secured against switching back on!
•Fuses must always be only replaced; never repaired or bridged. The specifications for
the maximum series fuse must always be adhered to (see Technical data). Only fuses
cited in the electrical circuit diagram may be used.
•Keep the airways of the fan free - danger because of objects dropping out!
•No maintenance work at running fan!
•Watch out for vibration free motion!
•The impeller is subject to natural wear depending on the area of application and the
conveying medium. Deposits on the impeller can lead to imbalance and damage
(danger of permanent fracture). The impeller can burst!
•Maintenance interval in accordance with the degree of contamination of the impeller!
•Check the impeller, in particular the weld-seams (in the appropriate versions), for
possible cracks.
•Repair, e.g. by welding or gluing is prohibited!
•Bolted-on or pressed on impellers and/or wings may only be replaced by authorised
ZIEHL-ABEGG SE staff. The manufacturer shall not be liable for damage caused
through improper repair work.
•Regular inspection and possibly cleaning is necessary to prevent imbalance and
blockage of the drain holes due to ingress of dirt.
•When opening cable glands on the fan / motor, check the condition of the threaded
connections and seals. Always replace defective or brittle threaded connections and
seals.
Info
Confirmation number for inquiries or in service cases see rating plate.
Assembly instructions FE2owlet-ECQ Service work
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
17/24

7.2 Cleaning
Danger due to electric current
•Voltage supply for motor must be interrupted and secured against restoration!
•Do not use any aggressive cleaning agents when cleaning.
•Make sure that no water gets into the inside of the motor and electronics.
8 Enclosure
8.1 Technical data
Line voltage*
(
Rating plate)
1 ~ 200...264 V, 50/60 Hz
1 ~ 100...134 V, 50/60 Hz
Power consumption (P1) Version with one speed: max 18 W
Version with three speeds: max. 34 W
Maximal line fuse 4 A
Max. load limit integral of cut-in current approx. 0.118 A
2
s
Permissible minimum and maximum ambient tem-
perature for operation
-40...+50 °C
Permissible temperature range for storage and
transport
-40...+80 °C
Permissible rel. humidity 85 % no condensation
Electromagnetic compatibility for the standard volt-
age 230 / 400 V according to IEC 60038
Interference emission according to EN 55014-1 (do-
mestic household applications)
Interference immunity according to EN 61000-4-4 (in-
dustrial applications)
Harmonics current In accordance with EN 61000-3-2
Please ask manufacturer for the individual harmonic
oscillation levels of the current as a percentage of the
fundamental oscillation of the rated current.
Ball bearings grease service-life (F
10h
) The device is designed with a life time for the bearings
and a bearings service-life of at least 40.000 h when S
operated at full power in the maximum permissible
ambient-temperature environment.
Connection Version with one speed: H03VV-F 2 x 0.5 mm
2
Version with three speeds: H03VV-F 3 x 0.5 mm
2
Protection class of motor according to EN 60529 IP55
Weight
rating plate
Assembly instructions FE2owlet-ECQ Enclosure
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
18/24

For motors with one speed and corresponding quality mark
(
rating plate)
Authorization: FILE No.
E347018
UL 1004-7
Electronically-Protected
Motor - Component
For motors with three speeds and corresponding quality mark
(
rating plate)
Authorization: FILE No.
E123518
UL 1004-3
Thermal-device-protected
Motor - Component
Assembly instructions FE2owlet-ECQ Enclosure
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
19/24

8.2 EC Declaration of Incorporation - Translation -
(english)
ZA87-GB 2022/17 Index 012
as defined by the EC Machinery Directive
2006/42/EC, Annex II B
The design of the partly completed machine:
Axial fan DN.., FA.., FB.., FC.., FE.., FF.., FG.., FH.., FL.., FN.., FP.., FS.., FT.., FV..,
VN.., VR.., ZC.., ZF.., ZG.., ZN..Centrifugal fan ER.., GR.., HR.., RA.., RD.., RE.., RF..,
RG.., RH.., RK.., RM.., RR.., RZ.., WR..Cross-flow fan QD.., QG.., QK.., QR.., QT..,
Motor type:
Induction internal or external rotor motor (also with integrated frequency
inverter)Electronically commutated internal or external rotor motor (also with integrated
EC controller)
Complies with the requirements in Appendix I, Articles 1.1.2, 1.1.5, 1.4.1, 1.5.1 in
EC Machinery Directive 2006/42/EC.
Manufacturer: ZIEHL-ABEGG SE
Heinz Ziehl Straße
74653 Künzelsau, Germany
The following harmonized standards have been applied:
EN 60204-1:2018 Safety of machinery – Electrical equipment of ma-
chines – Part 1: General requirements
EN ISO 12100:2010 Safety of machinery – General principles for design
– Risk assessment and risk reduction
EN ISO 13857:2019 Safety of machinery – Safety distances to prevent
hazard zones being reached by upper and lower
limbs
Note: Compliance with EN ISO 13857:2019 relates only
to the installed contact protection if it is part of the
scope of delivery.
The special technical documents in accordance with Appendix VII B have been created
and are available in full.
Assembly instructions FE2owlet-ECQ Enclosure
L-BAL-F062-GB 2022/20 Index 004 Part.-No. 00702389-GB
20/24