zinetic TN210 User manual

Toner that doesn’t cost the earth
Printed on recycled paper, using refilled cartridges
www.zinetic.co.uk email: [e-mail]
INSTRUCTIONS FOR REFILLING BROTHER TN210/TN230 C RTRIDGE
PRINTER COMP TIBILITY: DCP-9010 CN, HL-3040CN, HL 3050CN, HL-30 0CW,HL-80 0, HL-83 0 ,MFC-
9010CN, MFC-9120CN, MFC-9320CN, MFC-9320CW. TN210/TN230.
Please read instructions from start to finish,
before you start your refill.
During the refill procedure do not touch the
developer roller (that runs the length of the
cartridge).
If you are refilling a cartridge that came free with
the printer you will need to purchase a reset gear.
When to refill:
The printer asks for the toner cartridge to be changed before all of the toner has been used. This is a
waste of toner and your money. Resetting the cartridge – this will force the printer to use up all of the
remaining toner in cartridge! This method is detailed in the printer’s engineers manual.
Ignore “Toner Low Message”
Reset at “Replace Toner Message” (Machine refuses to print).
How to reset via the printers control panel
• Open the front cover of your Brother laser printer where you access the toner cartridges.
• Press the Clear / Back button until you see the toner menus appear on the small LCD
screen
• Press the arrow keys in order to navigate through to the toner cartridges you need to
reset
• Hit “OK” to reset the toner cartridges that report as empty.
• Press 1 to reset the cartridge
• Scroll through and repeat for each toner cartridges colour that reports empty.
• Exit the menu and close the cover
Once you have reset the cartridge you can continue to print until the colours fade from your
prints. When you are not happy with the print quality then refill your cartridge.
K = Black
C = Cyan
M = Magenta
Y = Yellow
STD = Standard Capacity Cartridge
STR = Starter Capacity Cartridge

Toner that doesn’t cost the earth
Printed on recycled paper, using refilled cartridges
www.zinetic.co.uk email: [e-mail]
1 Switch printer off.
2 Remove drum and cartridge from printer.
Separate the cartridge from the drum unit. Store
drum unit out of direct light.
Place printer cartridge on several sheets of
newspaper.
3 Locate the hopper
cap on your
cartridge.
Hidden behind the
label.
4 Remove the
hopper cap using
needle nose pliers,
or a flat blade
screwdriver to lever
out the hopper cap.
Do not worry if you
damage the cap as
a new cap is
provided. Do not
damage the
cartridge.
5 W RNING: You must ensure all toner is
dumped from your cartridge before refilling with
the new toner.
Important - mixing new and old toner will cause
print defects to occur.
Empty in an area
that can tolerate a
toner spill i.e. your
garage.
Toner can be very
messy - empty the
old toner directly
into a large bin bag.
6 Shake your bottle
of new toner
vigorously for 30
seconds BEFORE
removing the cap.
Remove the cap and
seal from the bottle
7 Fit the toner
pouring spout
securely to the
bottle.
Spouts are
reuseable.
8 Insert the spout
into the hole. The
toner will flow out
like water, so take
care not to spill it.
9. With the spout
inserted –
carefully “Upend”
the cartridge and
allow the toner to
slowly pour into the
cartridge.
10 Replace the cap
in your toner
cartridge, using the
new cap provided.
11 Gently rock the cartridge from side to side to
distribute the toner in the cartridge.
Wipe away any excess toner from around the plug.
Reset the gear as below.

Toner that doesn’t cost the earth
Printed on recycled paper, using refilled cartridges
www.zinetic.co.uk email: [e-mail]
RESETTING THE C RTRIDGE
1. Remove the 2 screws as shown opposite.
2. Use a small flat blade screwdriver to release
locking clip at the back of the cartridge.
Carefully remove the end plate to reveal the
gears as shown.
(When you remove the end plate the gears &
cogs may fall off be careful not to loose any of
them as they must be replaced.)

Toner that doesn’t cost the earth
Printed on recycled paper, using refilled cartridges
www.zinetic.co.uk email: [e-mail]
3Set the flag gear spring on the post as shown.
Picture opposite shows the gear, in the correct
reset position. The tail of the spring fits into a
notch at the base of the gear shaft.
The teeth of the reset gear should start to
mesh with the other gear.
If no gear is present, you can purchase a replacement
gear, please contact us.
4. Re install the gear cover plate and 2 screws.
You are now ready to replace your cartridge in
the printer and resume printing

Toner that doesn’t cost the earth
Printed on recycled paper, using refilled cartridges
www.zinetic.co.uk email: [e-mail]
Other things the machine uses :
Waste toner box – change as required.
Drum units - drums are independent of the toner cartridge. Change or reset as required.
REPETITIVE DEFECT CHART:
Developer roller 31.0 mm
OPC drum 94.0 mm
Upper fuser roller 8.0 mm
Lower pressure roller 8.0 mm
Safety information:
•Toner powder should be treated as a nuisance dust. Not to be used by children.
•Avoid inhalation. Avoid eye & skin contact. Do not ingest. Inhalation: slight irritation of respiratory tract.
Consult a doctor. Eye contact: Dust may cause irritation by mechanical abrasion. Consult a doctor.
•Skin contact: wash with soap and cold running water. Ingestion: No known hazard. Carcinogenicity: N/A,
Mutagenicity: AMES test negative.
All safety information is given to help facilitate the safe use of this product and is based on information
obtained from the manufacturer. This information is believed to be correct, but does not purport to be all
inclusive and should be used only as a guide. Zinetic makes no warranty, express or Implied as to the
accuracy or completeness of this information. It is the users responsibility to determine the suitability of this
information for the adoption of necessary safety precautions and or compliance with local laws/regulations.
Zinetic is not associated with or endorsed by any of the cartridge / printer manufacturers referred to in any of
our published works. Names of manufacturers, machines and part numbers are given as an aid to
identification only. Names of manufacturers, machines and part numbers may be trade marks of the
respective manufacturer. All Trade Marks hereby expressly acknowledged.