Zte MF63 User manual

Getting to Know Your Device
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057
Let’s
Getting started with your device
ZTE MF63
GO
Appearance
The following gure is only for your reference. The actual product may be
different.
1. OLED Screen
2. microSD Card Slot
3. WPS Button
4. RESET Button
5. Micro USB Port
6. (U)SIM Card Slot
7. Power Switch
8. External Antenna Connector
NOTES:
• microSD logo is a trademark of SD Card Association.
• Please use the original external antenna if necessary.
Indicators
When the device is powered on, the following icons will appear on the
OLED screen, with the corresponding indicates listed in the table below:
Icon Indication
Network signal strength.
Network type. 2G or 3G icon will appear on the OLED
screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
New message received.
Wi-Fi Status and number of the connected users.
Battery power indication.
Connection Scenario
Your device supports two methods to go to Internet and supports multi-
clients for surng on the Internet at the same time. The following gure is
only for your reference.
Installing Your Device
• 3G Mode: Use your (U)SIM card to access the Internet.
• AP Station Mode: Your device will connect to other WLAN device
(hotspot device, wireless router, etc.) via Wi-Fi to access the
Internet. The WLAN device has already connected to the Internet.
NOTE:
The subnet must be deferent between your device and other WLAN
device.
1. Slide the back cover and remove it
2. Insert the SIM card.
3. Insert the battery.
4. Close the back cover.
5. (Optional) Insert the SD card.
1) Open the microSD card cover.
NOTE: Do not pull the cover rudely, as it is connected with the device.
2) Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
3) Close the microSD card cover.
Connecting to Your Device
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the
available wireless networks.
NOTE: Please set the client to obtain an IP address automatically
referring to the chapter “Conguring your PC”, and then the client will get
an IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click Connect.
4. Input the password, and then click Connect.
NOTE:
You may need to input the password for Wi-Fi connection, and then
please check the label on your device to get the default.
5. Wait a moment, and then the client will connect to your device
successfully.
LEGAL INFORMATION
Copyright © 2012 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
photocopying and microlm, without the prior written permission of ZTE
Corporation.
The manual is published by ZTE Corporation. We reserve the right to
make modications on print errors or update specications without prior
notice.
Version No. : R1.0
Via USB Cable
1. Connect to the device.
2. Power on your device.
3. The OS detects and recognizes new hardware and finishes the
installation automatically.
NOTE:
If the system does not launch installation automatically, you can run the
installation program in path of My Computer > ZTEMODEM.
4. Wait a moment, and then the client will connect to your device
successfully.

Follow the following steps and gures for Windows XP to congure the
Internet Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and then select Properties.
2. Right-click Wireless Network Connection, and then select
Properties.
3. Select Internet Protocol(TCP/IP), and then click Properties.
4. Select Obtain an IP address automatically and Obtain DNS server
address automatically, and then click OK to nish the conguration.
To the Owner
• Some electronic devices are susceptible to electromagnetic
interference sent by your device if inadequately shielded, such as
the electronic system of vehicles. Please consult the manufacturer of
your device before using if necessary.
• Operating your device may interfere with medical devices like
hearing aids and pacemakers. Please always keep them more than
20 centimeters away from such medical devices when they are
turned on. Turn your device off if necessary. Consult a physician or
the manufacturer of the medical device before using your device.
• Be aware of the usage limitation when using your device at places
such as oil warehouses or chemical factories, where there are
explosive gases or explosive products being processed. Turn off
your device if required.
• The use of electronic transmitting devices is forbidden in aircrafts, at
petrol stations and in hospitals. Please observe and obey all warning
signs and switch off your device in these conditions.
• Do not touch the inner antenna area if not necessary. Otherwise it
will affect your device’s performance.
• Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
• Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Using Your Device
• Please use original accessories or accessories that are authorized.
Using any unauthorized accessories may affect your device’s
performance, and violate related national regulations about telecom
terminals.
• Avoid using your device near or inside metallic structures or
establishments that can emit electromagnetic waves. Otherwise it
may inuence signal reception.
• Your device is not waterproof. Please keep it dry and store in a
shady and cool place.
• Do not use your device immediately after a sudden temperature
change. In such case, it will produce dew inside and outside your
device, so don’t use it until it becomes dry.
• Handle your device carefully. Do not drop, bend or strike it.
Otherwise your device will be damaged.
• No dismantling by non-professionals and only qualied technicians
can undertake repair work.
• Operating temperature range of 0°C ~ +35°C and humidity range of
5% ~ 95% are recommended.
Using Battery
• Do not short-circuit the battery, as this can cause excessive heat and
re.
• Do not store battery in hot areas or dispose of it in a re to avoid
explosion.
• Do not disassemble or modify the battery.
• When not using the battery for a long period, remove it from your
device and store it in a cool dry place.
• Never use any charger or battery damaged or worn out.
• Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
WARNING:
If the battery is broken, keep away from it. If it taints your skin, wash your
skin with abundant fresh water and ask doctor help if necessary.
Limited Warranty
• This warranty does not apply to defects or errors in the Product
caused by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper
installation, disassembly, storage, servicing or operation of the
Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified
individual.
v. Power failures, surges, fire, flood, accidents, actions of third
parties or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with
third-party products provided that such defects are due to the
combined usage.
vii. Any other cause beyond the range of normal usage intended for
the Product.
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability
for defective or nonconforming items, and is in lieu of all other
warranties, expressed, implied or statutory, including but not
limited to the implied warranties of merchantability and tness for a
particular purpose, unless otherwise required under the mandatory
provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of prots or indirect, special, incidental
or consequential damages resulting from or arising out of or in connection
with using of this product, whether or not ZTE had been advised, knew
or should have known of the possibility of such damages, including, but
not limited to lost prots, interruption of business, cost of capital, cost of
substitute facilities or product, or any downtime cost.
Accessing the Internet
3G Mode
After the client connected to your device successfully, you can access
the Internet in the Automatic or Manual mode. The default mode is
Automatic.
Mode Operations
Automatic Your device will connect to the Internet automatically, and
your clients can surf on the Internet directly.
Manual
Login the webGUI conguration page, and select Settings
> 3G Settings > Network Select > WAN Connection
Mode > Manual, and then click Connect or Disconnect.
NOTE:
If you want to modify the detailed parameters of your device, please login
the webGUI configuration page by visiting http://192.168.0.1 or http://
m.home. The default password is admin.
AP Station Mode
1. Login the webGUI conguration page.
2. Select Settings > AP Station.
3. Set the AP Station parameters, and then click Apply.
NOTE:
You need select Wi-Fi Prior.
4. Connect to the WLAN device.
There are two methods for your reference.
• Input the WLAN device information in the WLAN Setting area,
and then click Apply.
• Click More, select this WLAN device which will be listed, and
then click Connect.
5. After the client connected to the WLAN device successfully, you can
access the Internet.
Conguring Your PC Warning and Notice
Problem Suggested Solution
Can not establish
the USB connection
between your
device and PC
• You need to install the software. Run the installation
program in path of My Computer > ZTEMODEM.
• If the driver of your device is abnormal, please reinstall the
software. You need uninstall the software rst.
Can not establish
the Wi-Fi
connection between
your device and
client
• Make sure the Wi-Fi function is active. Press the WPS
button to enable or disable Wi-Fi function.
• Refresh network list and select the correct SSID.
• Check the IP address to make sure your client can obtain
an IP address automatically in the Internet protocol (TCP/IP)
properties.
• Type the correct network key (Wi-Fi password) when you
connect to the device.
The client
connected to the
device can not
access the Internet
• Make sure your SIM card is available.
• Change the location to nd a place with good signal.
• Check WAN Connection mode setting.
• Contact with your service provider and conrm your APN
settings.
When I use AP
Station mode, the
client cannot access
the Internet.
• Make sure the other WLAN device has already connected
to the Internet.
• Make sure that the subnet of your device and the other
WLAN device is different
Can not visit
the webGUI
conguration page
• Enter the correct address. The default address is
http://192.168.0.1 or http://m.home.
• Only use one network adapter in your PC.
• Do not use any proxy server.
About the password
• For the Wi-Fi connection password, please check the label
on the device.
• Press the WPS button twice, and then the SSID and Wi-Fi
connection password appear on the screen.
• The default password of the webGUI conguration page is
admin.
• If you changed the password and forgot the new password,
you need to restore the device to the factory default settings.
Troubleshooting
For more assistance, please:
• Send E-mail to [email protected]
• Visit http://www.zte.com.cn
• Call Service Hotline: +86–755–26779999
NOTE:
Do not use the device in an enclosed environment or where heat dissipation is
poor. Prolonged work in such space may cause excessive heat and raise ambient
temperature, which may lead to automatic shutdown of the device for your safety.
In the case of such event, cool the device in a well-ventilated place before turning
on for normal use.
Other manuals for MF63
2
Table of contents
Other Zte Wireless Router manuals