ZyXEL Communications P-660HNU-F1 Operator's manual

www.zyxel.com
Wireless N ADSL2+ 4-port USB
Gateway
Firmware Version 3.10
Edition 1, 07/2011
P-660HNU-F1
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
Admin Login: User Name: admin
Password: 1234
User Login: User Name: user
Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 13
FRANÇAIS 25
ITALIANO 37
Copyright 2011
ZyXEL Communications Corporation

2
Device Panels
WLAN/WPS
ON/OFF
POWER
LED
DSL
INTERNET
LED
WLAN/WPS
LED
ETHERNET
LED
USB
LED
ON/OFF
RESET
POWER
ETHERNET
PORTS
DSL
PORT
USB
PORT
CONNECTOR
SWITCH

3
ENGLISH
Requirements
Make sure you have the following things before you start.
• INTERNET ACCESS: You need an Internet account with an ISP
(Internet Service Provider) and information such as user name,
password, and so on.
• 3G ACCOUNT: You need this if you want to use a 3G connection to
access the Internet. The P-660HNU-F1 can also use this 3G
connection as a backup if the DSL connection fails.
• WEB BROWSER: Internet Explorer 6.0 and later versions, with
JavaScript enabled, or Mozilla Firefox 3 and later versions or Safari
2.0 and later versions. The browser will be used to access the
Internet and/or access the P-660HNU-F1’s Web Configurator.
ENGLISH

4
Hardware Connections
Remove the P-660HNU-F1’s plastic wrapping before using it.
1. DSL: Use a telephone wire to connect this port to the telephone wall
jack. If you are using a splitter, use a telephone wire to connect this
port to the DSL/MODEM jack on the splitter. Use another telephone
wire to connect the PHONE jack in the splitter to the telephone wall
jack.
2. ETHERNET: If you want a wired connection to the P-660HNU-F1, use
an Ethernet cable to connect a computer to one of these ports for
initial configuration and/or Internet access.

5
ENGLISH
3. USB 2.0: You only need to use this port if you are connecting a USB
storage device, USB printer or a 3G adapter to the P-660HNU-F1.
4. POWER: Use the power adaptor provided with your P-660HNU-F1 to
connect this socket to an appropriate power source.
5. Push the power button to the on position and look at the LEDs (lights)
on the top panel of the P-660HNU-F1.
• The POWER light blinks during start-up and stays on once the P-
660HNU-F1 is ready.
• The ETHERNET light turns on if the corresponding ETHERNET
port is properly connected. If you do not connect a computer
correctly to this port, the ETHERNET light will not turn on.
• The WLAN/WPS stays on when the wireless LAN is ready. The
light will not turn on if the Wireless Connection is not activated.
The ETHERNET and WLAN/WPS lights blink when the P-660HNU-F1 is
sending or receiving data. If the POWER light does not turn on during
start up, try turning the P-660HNU-F1 off, check the connections, wait a
few seconds and then turn it back on. If the problem persists, you may
have a hardware problem and you need to contact your vendor.

6
Internet Access Setup
The DSL and INTERNET lights are on if you have internet access. Open
your web browser and browse to www.zyxel.com. You may be prompted
to enter your username and password.
If one or both of these lights are not on, try turning the P-660HNU-F1 off,
check the connections, wait a few seconds and then turn it back on. If
the DSL light is not on, contact your service provider. If the DSL light is
on but the INTERNET light is not, you need to enter your Internet access
configuration using the Web Configurator - see page 10.
Setting Up a Wireless Connection
If you want to set up a wireless connection using the P-660HNU-F1, use
one of the following methods:
1. Use the wireless SSID (network name) and WPA-PSK encryption key
if the device does not have the WPS logo - see page 7.
2. Use the WPS/WLAN Button if your wireless device has a Wi-Fi
Protected Setup (WPS) logo - see page 9

7
ENGLISH
Setting Up a Wireless Connection using the
Information on the Label
The wireless function on your P-660HNU-F1 is enabled by default. Press
the WLAN/WPS button on the P-660HNU-F1’s top panel for 1 second to
turn this function on or off.
To add a wireless client to the network, use the settings found in the rear
panel of the P-660HNU-F1, such as the following:
1. Right-click the wireless adapter icon which appears in the bottom
right of your computer monitor. Click View Available Wireless
Networks.
SSID: Zy_private_R9XP9P
WPA2-PSK: 7WC3R7TVKWK3R

8
2. Select the P-660HNU-F1’s SSID name and click Connect (A). The
SSID “SecureWirelessNetwork” is given here as an example.
3. You are prompted to enter a password. Enter the WPA-PSK
encryption key found in the rear panel of the P-660HNU-F1 and click
Connect.
4. You may have to wait several minutes while your computer connects
to the wireless network.
5. You should now be securely connected wirelessly to the P-660HNU-
F1.
A

9
ENGLISH
 If you cannot connect wirelessly to the P-660HNU-F1, check
that you have selected the correct SSID and entered the
correct security key. If that does not work, ensure that the
WLAN/WPS LED on the front panel is turned on.
Setting Up a Wireless Connection using WPS
Follow these steps to add a WPS-enabled device to the wireless network
using the WLAN/WPS button.
You must use WPS one device at a time with the P-660HNU-F1.
Place the devices you want to connect
near one another.
Press the WLAN/WPS button on top of
the P-660HNU-F1 for more than 5
seconds to turn the WPS function on or
off.
The WLAN/WPS light blinks.
Press the WPS button on a compatible
device within 2 minutes of pressing the
button on the P-660HNU-F1.
The WLAN/WPS light on the P-
660HNU-F1 shines steadily when
connected.
1
2
3

10
The Web Configurator
The Web Configurator is a web browser tool that allows you to configure
the P-660HNU-F1. The computer and the P-660HNU-F1 need to be in
the same IP address range to use this tool.
1. Open your browser and enter http://192.168.1.1 (the P-660HNU-F1's
default IP address) as the address.
2. For administrator login, enter username admin and password 1234
(default). For user login, enter user as the username and 1234 as the
password. Click Login.
 If the login screen does not open, make sure you allow web
browser pop-up windows, JavaScript and Java permissions.
Your computer should also be set to get an IP address
automatically from a DHCP server. See your User’s Guide
for more information.
3. If the INTERNET light is off, manually configure the Internet
connection. Click Network Setting, then click on Broadband, and
then click on Add new WAN Interface (Network Setting >
Broadband > Add new WAN Interface).