ZyXEL Communications P-2602R/RL-DXA User manual

P-2602R/RL-DxA
ADSL2+ VoIP IAD
Quick Start Guide
Version 3.40
5/2006
Edition 1

P-2602R/RL-DxA Quick Start Guide
2
Overview
The P-2602R/RL-DxA ADSL2+ VoIP Integrated Access Device (IAD) is an ADSL2+ router with phone ports for
making calls over the Internet (Voice over IP or VoIP). It can also use regular phone services through regular
(PSTN) phone lines. See the User’s Guide for more information on all features.
The following figure shows how your P-2602R/RL-DxA (A) connects your network to the Internet, provides
firewall protection and allows you to make telephone calls over the Internet. Additionally, the P-2602RL-D
model can be used to make calls over regular telephone (PSTN) lines.
1 Requirements
Make sure you have the following things before you set up your P-2602R/RL-DxA.
• Internet access - account information provided by your ISP, such as user name, password, and so on.
• VoIP account - You need the account information provided by your VoIP service provider (the company that lets
you make phone calls over the Internet). This information might include your URI, number, and so on.
• Internet Explorer 6.0 or later or Netscape Navigator 7.0 or later, with JavaScript enabled.
2 Hardware Connections
Hardware connections vary by model. The P-2602RL-DxA models have a built in lifeline and the P-2602R-
DxA do not.

P-2602R/RL-DxA Quick Start Guide
3
2.1 P-2602RL-DxA Hardware Connections
1DSL: Use the gray ADSL cable to connect the telephone jack or the DSL or MODEM jack on a splitter to
this port.
2LINE: Use the green PSTN line cable to connect the telephone jack or the TEL or PHONE jack on a splitter to
this port.
Note: When the P-2602R/RL-DxA does not have power, only the phone connected to the
PHONE 2 port can be used for making calls. Ensure you know which phone this is, so
that in case of emergency you can make outgoing calls.
3ETHERNET: Use an Ethernet cable to connect a computer to this port for initial configuration and/or
Internet access.
4 PHONE 1-2: Use telephone cables (and any telephone adaptors provided with your P-2602RL-DxA) to
connect your telephones to these ports. If you only have one telephone, you should use port 1.
5POWER:Use the power adaptor provided with your P-2602RL-DxA to connect an appropriate power
source to this socket.
Note: If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it
to a telephone wall jack or the telephone splitter's TEL or PHONE jack.

P-2602R/RL-DxA Quick Start Guide
4
6Push in the POWER button. Look at the lights on the front panel of the P-2602RL-DxA.
•ThePOWER light blinks during start-up and is green once the P-2602RL-DxA is ready.
• Each ETHERNET light turns on if the corresponding ETHERNET port is properly con-
nected. The lights blink when the P-2602RL-DxA is sending or receiving data through the
corresponding ETHERNET port.
•TheDSL light stays on if a physical connection with the ISP is established. The INTER-
NET light stays on when Internet access is available.
•ThePHONE lights stay on when your SIP account is registered and they blink if the
receiver is off hooked.
If PHONE 1 or PHONE 2 light is on, skip to Section 4to see how to make calls through
the Internet.
If the INTERNET light comes on but the PHONE lights are off, go to Section 3.2 and use
the VOICE OVER INTERNET SETUP wizard.
If the INTERNET light is off but the DSL light is on, go to Section 3.1 and use the
INTERNET SETUP wizard to configure your Internet access settings.

P-2602R/RL-DxA Quick Start Guide
5
2.2 P-2602R-DxA Hardware Connections
1DSL: Use the gray ADSL cable to connect the telephone jack or the DSL or MODEM jack on a splitter to
this port.
2ETHERNET: Use an Ethernet cable to connect a computer to this port for initial configuration and/or
Internet access.
3 PHONE 1-2: Use a telephone cable (and any telephone adaptors provided with your P-2602R-DxA) to
connect your telephones to these ports. If you only have one telephone, you should use port 1.
4POWER:Use the power adaptor provided with your P-2602R-DxA to connect an appropriate power source
to this socket.
Note: If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it
to a telephone wall jack or the telephone splitter's TEL or PHONE jack.

P-2602R/RL-DxA Quick Start Guide
6
5Push in the POWER button. Look at the lights on the front panel of the P-2602R-DxA.
•ThePOWER light blinks during start-up and is green once the P-2602R-DxA is ready.
• Each ETHERNET light turns on if the corresponding ETHERNET port is properly con-
nected. The lights blink when the P-2602R-DxA is sending or receiving data through the
corresponding ETHERNET port.
•TheDSL light stays on if a physical connection with the ISP is established. The INTER-
NET light stays on when Internet access is available.
•ThePHONE lights stay on when your SIP account is registered and they blink if the
receiver is off hooked.
If PHONE 1 or PHONE 2 light is on, skip to Section 4to see how to make calls through
the Internet.
If the INTERNET light comes on but the PHONE lights are off, go to Section 3.2 and use
the VOICE OVER INTERNET SETUP wizard.
If the INTERNET light is off but the DSL light is on, go to Section 3.1 and use the
INTERNET SETUP wizard to configure your Internet access settings.
3 Initial Configuration
Open your web browser, and go to http://www.zyxel.com.
Your P-2602R/RL-DxA tries to detect your Internet connection. This takes about two minutes. If any other
screens appear, follow the directions in the screen.

P-2602R/RL-DxA Quick Start Guide
7
If http://www.zyxel.com opens correctly, your Internet access is ready. If the web page does not open, use the
following steps. You should have information provided by your ISP.
1Open your browser, and go to http://192.168.1.1.2Enter the password 1234. Then, click Login.
If your browser cannot find this screen, make sure
your browser is configured correctly. See
Troubleshooting in the User’s Guide for details.
3Type (and retype) a new password and click
Apply.

P-2602R/RL-DxA Quick Start Guide
8
3.1 Internet Setup
Note: You should have the information provided by your ISP.
1Click INTERNET SETUP.
Wait while the P-2602R/RL-DxA tries to detect your
Internet connection. If the P-2602R/RL-DxA cannot
detect your Internet connection, follow the directions
in the screens. Enter the information provided by your
ISP. Keep the default settings if your Internet service
provider did not provide some information.
When your Internet connection is setup correctly, the INTERNET light should be green, and the following
screen appears.
4Click Go to Wizard setup. Then, click Apply.

P-2602R/RL-DxA Quick Start Guide
9
3.2 VoIP Setup
Note: You should have the information provided by your VoIP service provider.
Click VOICE OVER INTERNET SETUP.
Enter the information provided by your VoIP service
provider. Keep the default settings if your VoIP
service provider did not provide some information. If
you have a SIP account like 1234567@VoIP-
provider.com, the SIP Number is 1234567, and the
SIP Service Domain is VoIP-provider.com.
When you are done, the PHONE light should be on. Click Exit to close the wizard and the main screen
appears.
3.3 Regular Phone Line Setup (“L” models)
When one of your VoIP accounts is registered, the P-2602RL-DxA normally uses the Internet (not the regular
phone line) to make phone calls. Follow the directions in this section to make sure you can also use the
regular phone line while one of your VoIP accounts is registered.
2Confirm that your Internet setup settings are
correct and click Return to Wizard Main Page to
continue with VoIP setup.

P-2602R/RL-DxA Quick Start Guide
10
Note: When the ZyXEL Device does not have power, only the phone connected to the PHONE 2 port
can be used for making calls. Ensure you know which phone this is, so that in case of emergency
you can make outgoing calls.
In the main screen, click VoIP >
PSTN Line.
PSTN Line Pre-fix Number: Enter 1
- 7 numbers you dial before you dial
the phone number, if you want to
make a regular phone call while one
of your SIP accounts is registered.
These numbers tell the ZyXEL
device that you want to make a
regular phone call.
Relay to PSTN Line: Enter phone
numbers for regular phone calls (that
do not use the Internet) that you
always want to dial without the prefix
number. For example, enter
emergency phone numbers here.
Click Apply.
4 Phone Calls
Follow these directions to make calls over the Internet.
• If you want to dial a SIP number that only uses numbers (for example, “12345”), dial the number on your
phone’s keypad. You can also set up a speed-dial entry, if you want. See the User’s Guide for instructions.