ZyXEL Communications P-660HW-D1 User manual

ZyXEL Confidential
340AGL4C0.doc 1/41
ZyXEL
Firmware Release Note
P-660HW-D1
Standard version
Release 3.40(AGL.4)C0
Date: Jan 10 ,2007
Author: Ross Meng

ZyXEL Confidential
340AGL4C0.doc 2/41
ZyXEL P-660HW-D1 Standard Version
Release 3.40(AGL.4)C0
Release Note
Date: Jan 10, 2006
Supported Platforms:
ZyXEL P-660HW-D1
Versions:
ZyNOS Version : V3.40(AGL.4) | 01/10/2007 12:00:00
Bootbase Version : V1.06 | 1/20/2006 9:44:11
Notes:
The P-660HW-D1, is 4th generation of ZyXEL ADSL product family. It is a high
performance ADSL/ADSL2/ADSL2+ router for small/medium office to have Internet
access and LAN-to-LAN application over the existing copper line. P-660HW-D1 takes
advantage of much higher data rate than ADSL, speed up to 12Mbps (ADSL2) or 26Mbps
(ADSL2+), greater reach, faster start-up, advanced diagnostics and better power
management. This high performance ADSL router is a high integrated advanced Firewall,
Bandwidth Management and IEEE 802.11g wireless features to meet the demand of
high-end market.
P-660HW-D1 provides an embedded mini-PCI module for 802.11g Wireless LAN
connectivity, four single auto-sensing, auto-detection 10/100BASE-T Ethernet ports for
connection to the user’s local network, and a single RJ-11/RJ-45 port for connection to
ADSL/ADSL2/ADSL2+ line.
ADSL data pump version: TI AR7 07.00.04.00
Features:
Modifications in V 3.40(AGL.4)C0 | 01/10/2007
1. change to FCS version
Modifications in V 3.40(AGL.4)b4 | 01/02/2007
1．[BUG FIX] SPRID: 061220169
Symptom: Triple Play don’t work
Condition: Bridege mode ,Enable TriplePlay ,the LAN PC can’t get IP from DHCP Server.
Disable TriplePlay ,the LAN PC can get IP from DHCP Server. Route mode,Enable
TriplePlay ,the LAN PC ping DHCP Server,can’t success. Disable TriplePlay ,the LAN PC
ping DHCP Server, successful.
Modifications in V 3.40(AGL.4)b3 | 12/12/2006

ZyXEL Confidential
340AGL4C0.doc 3/41
1．[BUG FIX] SPRID: 061201023
Symptom: More connection has problem.
Condition: When you choose PPP encapsulation in Wan/More Connection, it will crush
or reboot: PPPoE + LLC + Dynamic/Static IP, PPPoA + LLC + Dynamic/Static IP,
PPPoA + VC + Static IP will lead to crush, PPPoA + VC + Dynamic IP will lead to
reboot.
2．[BUG FIX] SPRID: 061201052
Symptom: Reboot Device have some problem
Condition: step1:In GUI,change System name. step2:In CLI,change baud = 115200.
step3:reboot Device. The Device show some abnormal information in CLI.
Modifications in V 3.40(AGL.4)b2 | 11/22/2006
1. [ENHANCEMENT]
Add SMT23.4 function CLI
2. [ENHANCEMENT]
In GUI page: MBM rule config add “DSCP mark” and “TOS” fileds
3. [BUG FIX] SPRID: 060915954
Symptom: Bridge RFC1483 can’t be set correctly in GUI-＞Wizard Setup-＞Internet
Setup.
Condition: Step1 Enter Wizard Setup and start Internet/Wireless Setup.
Step2 When DSL Auto detected fails, select Bridge RFC1483 mode and apply it. It will
still show this configuration page.
Step3 But enter Advance Setup you can see the configuration have been saved
successfully
4. [BUG FIX] SPRID: 060915962
Symptom: Bandwidth MGMT rule with bandwidth larger than 65535 can’t be added
correctly.
Condition: Step1.Bandwidth MGMT-＞Summary LAN interface-＞Speed set to
100000.
Step2. Enter Bandwidth MGMT-＞Rule Setup and add a rule with Bandwidth smaller
than 65536, it will be added correctly.
Step3. Enter Bandwidth MGMT-＞Rule Setup and add a rule with Bandwidth larger
than 65536, the bandwidth which will be saved is the bandwidth you have entered
subtract 65536, for example you have entered 65537, it will be saved as 1
5. [BUG FIX] SPRID: 060915970
Symptom: In Wizard or use CLI command, Wireless SSID accept invalid characters as
@#~^%
Condition: In Wizard or use CLI command, Wireless SSID accept invalid characters as
@#~^%
6. [BUG FIX] SPRID: 060915969
Symptom: In GUI-＞Security-＞Firewall-＞Rules, add rules in 4 packet directions,
when we change any rule ”Active” check box in one of the directions, the others’ will be
changed accordingly.

ZyXEL Confidential
340AGL4C0.doc 4/41
Condition: In GUI-＞Security-＞Firewall-＞Rules, add rules in 4 packet directions,
when we change any rule ”Active” check box in one of the directions, the others’ will be
changed accordingly.
7. [BUG FIX] SPRID: 060915965
Symptom: When add remote node in GUI DUT will crash.
Condition: step1.WAN page set PPPOE and PPPOE passthought click open
step2. More connection set PPPOE apply then it will crash.
8. [BUG FIX] SPRID: 060915973
Symptom: Wireless QoS has problem.
Condition: 1.When use Wireless QoS Application Priority,edit one rule ,Dest
Port=65535 .
2.Use CLI command we can’t send packets to the port.
9. [BUG FIX] SPRID: 060915971
Symptom: In GUI , Wireless shows error message in Packet Status interface.
Condition: when 4x enable ,in Packet Status interface still show 54M.
10. [FEATURE CHANGE]
Use new compressed method to compress firmware.
11. [ENHANCEMENT]
In GUI status pages display four LAN ports status and DSL firmware version
12. [ENHANCEMENT]
Update modem code to Version 7.0.4.0
13. [ENHANCEMENT]
Supports 1530 bytes frame pass through in RFC1483 bridge mode.
14. [BUG FIXED] SPRID: 061121146
Symptom:Reboots problems in traffic jam conditions and huge NAT entries
Condition: Step1:config one PVC dynamic get IP and one PVC static IP
Step2: config one static route rule ,gateway point to static WAN IP.
Step3:run Portscan software in LAN PC,when scan port >10000, DUT will reboot
15. [ENHANCEMENT]
IGMP Snooping enable/disable setting can save to SPT ，configured via CI command:
sys tripleplay igmpsnp enable/disable
Modifications in V 3.40(AGL.4)b1 | 07/17/2006
1. [ENHANCEMENT]
Support APDK 6.3.1.26
2. [ENHANCEMENT]
Triple play V2 for 6996I
3.[ENHANCEMENT]
Update TI modem code to D6.0.4.0
4. [ENHANCEMENT]
Add G+ in wireless status. Remove "Active" in LAN and WLAN status.
5. [BUG FIX] SPRID: 060706288
Symptom: when edit a BM rule, if the bandwidth of the child is larger than the
bandwidth of the parent, it can be saved.

ZyXEL Confidential
340AGL4C0.doc 5/41
Condition: step1:Add a BM rule and save it.
step2:Edit the rule again, and change the bandwidth of the child larger than the
bandwidth of the parent, but it can be saved.
6. [BUG FIX] SPRID: 060706289
Symptom: In GUI, Status page --＞WLAN Information--＞WEP show is not
correct when set some Security such as WPA,WPA-PSK,WPA2,WPA2-PSK.
Condition: Step1: set Security Mode : Static WEP. The Status page show WEP:64-bit
WEP Step2: set Security Mode : WPA . The Status page still show WEP:64-bit WEP
7. [BUG FIX] SPRID: 060706290
Symptom: The configuration pages in administrator mode can be log in in user mode.
Condition: Step1. log in the user mode. Step2. paste the url of the administrator
configuration page in address bar and press enter,then log in the configuration page.
8. [BUG FIX] SPRID: 060706291
Symptom: Wan /more connections/ NAT edit lead to crash.
Condition: Step1. Restore default setting.
Step2. Enter WAN/More Connections, edit one of the connections, then enter NAT SUA
Only edit. After your apply it, It shows Address Mapping rule to edit, when you apply it,
the device will crash.
Or if you choose Back, then edit the connection again, it will enter Address Mapping
rule edit directly.
9. [BUG FIX] SPRID: 060706292
Symptom: When deleting firewall rules, it has problem.
Condition: Step1. In default setting, add 5~6 firewall rules in GUI.
Step2. Delete one of the rules, two rules may be deleted together and the firewall rule
numbers may be disordered. Step3. It will happen sometimes, but the frequence is very
high.
10. [BUG FIX] SPRID: 060706293
Symptom: When add new rule after rule number 9 ,it will show error.
Condition: step 1.Add nine firewall rules.
step 2.Insert a new rule after rule number 9,it shows "INTERNEL ERROR".
but insert a new rule after rule number 1~8,it can be inserted successfully.
11. [BUG FIX] SPRID: 060706294
Symptom: In GUI bandwidth management, when you add more than nine rules, it will
show ”Number of classes reaches the upper bound. Max classes is 9”
Condition: N/A
12. [BUG FIX] SPRID: 060706295
Symptom: GUI status can’t show correct information.
Condition: When WLAN 4x mode enabled, and one client connect to the AP, the
transmission rate shows 125M in client,but in GUI status shows 54M.
13. [BUG FIX] SPRID: 060706296
Problem Symptom:In GUI-＞WAN ,Set two or more remote node, and use same
encapsulation,different VPI/VCI,set static IP. Then delete one rule and set the same
setting in other remote node. Lan PC or device ping the gateway, the device will crash.
Problem Condition:

ZyXEL Confidential
340AGL4C0.doc 6/41
Step1:GUI-＞WAN set two remote node,and use same encapsulation,different VPI/VCI,
and set static IP. Lan PC ping remote node 2 gateway successfully.
Setp2: Delete the remote node 2, and set the same setting in other rule, such as remote
node 5. Lan PC ping remote node 5 gateway, the device will crash.
14. [BUG FIX] SPRID: 060706297
Symptom: CI Command "ip nat server clear [set#]" can not work
Condition: step1:In SMT or GUI add several server
step2:In SMT,use CI Command "ip nat server load [set#]","ip nat server clear [set#]"
and "ip nat server save",it can not clear the server [set#].
15. [BUG FIX] SPRID: 060706298
Symptom:When you add Firewall Rules, another rule will be added automatically.
Condition:1.Add rules one by one,2.When you add the fourth rule, the rule you have
edited will be added, and the fifth rule with default setting will be added
automatically.3.You can add rules continuously, it always shows the same results. For
example, you add the sixth rule , the seventh rule with default setting will be added
automatically
16. [BUG FIX] SPRID: 060706299
Symptom: Can't add 11th Port Forwarding set in eWC NAT.
Condition: If want to add 11th Port Forwarding set, system displays "Max number of
Port Forwarding rules can be added is 11" and won't accept. Iin CI, system allow users to
add 11th set and can see it in eWC.
17. [BUG FIX] SPRID: 060706300
Symptom: LCP echo request ,LCP echo reply and OAM packets are lost under some
stress test.
Condition: PC uploads data via Iperf traffic load simulator with UDP packets ,then
PPPoA connection disconnects after 30-60 seconds and recovers after 30-40 seconds.
18. [FEATURE ENHANCE]
User can set NAT session number per host In GUI
19. [FEATURE ENHANCE]
RomPager upgrade to version 4.5
Modifications in V 3.40(AGL.3)C0 | 05/29/2006
1．Change to FCS version
Modifications in V 3.40(AGL.3)b1 | 05/29/2006
1 . [FEATURE ENHANCE]
Add reset button WLAN Active--Inactive behavior, the reset button new behavior is
below:
For WLAN model:
- 1 sec: enable/disable WLAN function
- 3 sec: enable OTIST
- 10 sec: reset to factory default
2. [FEATURE ENHANCE]
Engineer note:Add CLI command to control wlan restart or not after download NVS
files.
3 . [FEATURE ENHANCE]

ZyXEL Confidential
340AGL4C0.doc 7/41
add wireless card check machine in HTP
Engineer note:
1 when WLAN Card exist, "WLAN LED" will be always on
2 when WLAN Card does not exist, "WLAN LED" will be always off
3 when WLAN Card disappear, "WLAN LED" will be off ,HTP test will be Break and
"SYSTEM LED" will be always on
4. [FEATURE ENHANCE]
Add SDRAM test in HTP
5. [BUG FIX] SPRID: 060529751
symptom: when use multiboot upload firmware ,wireless NVS file will need upload
again.
Condition:use multiboot upload firmware, wireless NVS file before upload will gone, it
need to upload again
Modifications in V 3.40(AGL.2)C0 | 05/17/2006
1. change to FCS version
Modifications in V 3.40(AGL.2)b1 | 05/16/2006
1. [FEATURE ENHANCE]
Modify to support ADM6996i AB,AC,AD version
Modifications in V 3.40(AGL.1) C0 | 03/17/2006
1. change to FCS version
Modifications in V 3.40(AGL.1) b1 | 03/15/2006
1. Update help pages
1) Maintenance > System > General
2) Network > Wireless LAN > OTIST
3) Security > Firewall
4) Advanced > BW MGMT
5) Advanced > Remote MGNT > ICMP
6) Status
Modifications in V 3.40(AGL.0) C0 | 03/13/2006
1 . change to FCS version
Modifications in V 3.40(AGL.0) b5 | 03/06/2006
1. [FEATURE CHANGE]
1). Default password for normal user: user. Default password for admin user: 1234.
web login page password default : user
2). remove the wizard set up from normal user level and remove change password
function for normal user so that normal user can directly view the status page.
2. change default romfile : Default password for normal user: user. Default password for
admin user: 1234.
Modifications in V 3.40(AGL.0) b4 | 03/05/2006
1. [BUG FIX] SPRID: 060302271
Problem Symptom: [Regression]Throughput bridge mode downstream ADSL(packet
length: 64,128) and ADSL2+ (packet length: 64,128,256,512) can’t meet PQA’s
criterion

ZyXEL Confidential
340AGL4C0.doc 8/41
Problem Condition: Throughput bridge mode downstream ADSL(packet length:
64,128) and ADSL2+ (packet length: 64,128,256,512) can’t meet PQA’s criterion.
2. [BUG FIX] SPRID: 060303431
Problem Symptom: Can not get current time from Time server
Problem Condition: step1. Reset default romfile. step2. Config the WAN, set the time
server and select the Time Zone is (GMT=08:00) Beijing, Chongqing, Hong Kong,
Urumqi, then click “Apply”. DUT can get current time and date. step3. Select Manual,
change New Time and New Date, then click “Apply”. step4. Set the time server, this
time it can get current date from time server, but can’t get current time.
3. [BUG FIX] SPRID: 060302268
Problem Symptom: [Regression]In GUI-> Maintenance-> Diagnostic->DSL Line page,
click “Capture All Logs”, the windows which would be show the info will be
disappear.
Problem Condition: In GUI-> Maintenance-> Diagnostic->DSL Line page, click
“Capture All Logs”, the windows which would be show the info will be disappear.
4. [BUG FIX] SPRID: 060301193
Problem Symptom: [Regression]Click the “apply” in wizard wireless page, the DUT
will crash..
Problem Condition: step1. Reset default romfile. step2. In GUI-> Wizard->wireless,
click “next”, “next”, then click “apply”, the DUT will crash.
5. [BUG FIX] SPRID: 060228275
Problem Symptom: [Regression]Set Secure Client IP, it can’t work
Problem Condition: step1. In GUI/ Advanced/ Remote MGMT/ WWW, set Secure
Client IP = 192.168.1.33.step2. Use one PC which IP is not 192.168.1.33, it can still
login GUI.step3. The FTP, TELNET have the same issue.
6. [BUG FIX] SPRID: 060302270
Problem Symptom: Disable the Wireless function, after period of times, LAN PC with
fixed IP ping LAN IP, only the first several ICMP reply packets can be received, then
will show “Request timed out”.
Problem Condition: step1. Use default setting, but disable the Wireless function. step2.
Using a LAN PC with fix IP (EX: 192.168.1.50) ping the DUT LAN IP (192.168.1.1),
and the ping traffic can be handled properly at this moment. step3. Stop the ping traffic
running from 192.168.1.50 to 192.168.1.1, and just leave the DUT powered on. step4.
After about 20 hours, start again the ping traffic from LAN PC to the DUT, will found
only the first several ICMP reply packets can be received, then will show “Request
timed out”, so others can not received.
7. [BUG FIX] SPRID: 060303429
Problem Symptom: [Regression]Bridge mode packet loss (packet size: 64) can’t meet
PQA’s criterion.
Problem Condition: Bridge mode packet loss (packet size: 64) can’t meet PQA’s
criterion.
8. [BUG FIX] SPRID: 060301196
Problem Symptom: Change the Qos type to VBR-RT, the LAN to WAN can’t work
correctly.
Problem Condition: step1. Config DUT, the LAN PC can ping WAN PC; the LAN to

ZyXEL Confidential
340AGL4C0.doc 9/41
WAN can work correctly. step2. Change the Qos type to VBR-RT, the LAN PC can’t
ping WAN PC, the LAN to WAN can not work correctly. step3. Then change the Qos
type to others type (ex.CBR), the LAN to WAN still can not work correctly; but if
reboot the DUT, it can work correctly. step4. The DUT works at bridge mode, it has the
same issue.
9. Change default romfile:turn off PPPoE Passthrough
10. Samsung flash support.
Modifications in V 3.40(AGL.0) b3 | 02/24/2006
1. [BUG FIX] SPRID: 051227526
Problem Symptom: set a schedule, when apply it use CI command “wan node callsch”,
it must fill 4 parameter, that is to say, you must type like this “wan node callsch 1 0 0 0”,
but not like “wan node callsch 1”.
Problem Condition: set a schedule, when apply it use CI command “wan node callsch”,
it must fill 4 parameter, that is to say, you must type like this “wan node callsch 1 0 0 0”,
but not like “wan node callsch 1”.
2. [BUG FIX] SPRID: 051228627
Problem Symptom: in GUI, the Qos have CBR, UBR,VBR-nRT, VBR-RT, but the CI
command it only have CBR, UBR.
Problem Condition: in GUI, the Qos have CBR, UBR,VBR-nRT, VBR-RT, but the CI
command it only have CBR, UBR.
3. [BUG FIX] SPRID: 060109394
Problem Symptom: (bug fixed not comlete)Click the “exit” button it have different
result
Problem Condition: Step1.in wizard or advanced, select “go to wizard set up”, then
click the “exit” button, it pop up a message “are you sure you want to close the
windows?”, select no, then the page won’t change.
Setp2.but if you select “view device status” or “change password” in wizard, or select
“go to advanced setup” in advanced, then do the same setting with step1, the page will
go to the corresponding page.
step3.login with user password have no this issue, but login with admin password this
issue is still exist.
4. [BUG FIX] SPRID: 060111543
Problem Symptom: In GUI-＞Advanced-＞Remote MGMT-＞SNMP, no matter
choose Disable, LAN, or WAN, MIB Browser can run both on LAN and WAN.
Problem Condition: In GUI-＞Advanced-＞Remote MGMT-＞SNMP, no matter
choose Disable, LAN, or WAN, MIB Browser can run both on LAN and WAN.
5. [BUG FIX] SPRID: 060111544
Problem Symptom: When DUT use static IP and set DNS server address in GUI-＞
wizard, LAN PC won＇t resolve domain name.
Problem Condition: Step1. Login with user password, configure DUT use static IP and
set DNS server in wizard setup page.
Step2. in LAN PC try to resolve domain name, but failed.

ZyXEL Confidential
340AGL4C0.doc 10/41
6. [BUG FIX] SPRID: 060112659
Problem Symptom: Whiteboard can’t work well when UPNP is enabling.
Problem Condition: Step1.firewall is enabling. Step2.Enable UPNP, WAN first ask for
whiteboard, the whiteboard can’t work. Step3.Enable UPNP and “allow users to make
configuration changes through UPnP”, the Whiteboard can’t work from LAN to WAN,
or WAN to LAN.
7. [BUG FIX] SPRID: 060113744
Problem Symptom: The word “dasable” in CI command “wan callsch action” was
spelled wrong
Problem Condition: Issue CI command ”wan callsch action”, it show [0:force on|
1:force down| 2:enable dial-on-command | 3:dasable dial-on command], the
word ”dasable” was spelled wrong, it should be ”disable”.
8. [BUG FIX] SPRID: 060113703
Problem Symptom: in the status page, the word “secondes” was spelled wrong.
Problem Condition: login in with user password or with admin password, in the status
page, the Refresh Interval item, the word “secondes” was spelled wrong, it should be
“seconds”.
9. [BUG FIX] SPRID: 060113745
Problem Symptom: set a filter, when apply it use CI command in WAN, it must fill 4
parameter, but apply it in LAN it need not to fill 4 parameter, it can be save when it
have only 1 parameter.
Problem Condition: set a filter, when apply it use CI command in WAN, it must fill 4
parameter, but apply it in LAN it need not to fill 4 parameter, it can be save when it
have only 1 parameter.
10. [BUG FIX] SPRID: 060113746
Problem Symptom: It will show “the flags is: 0x00000007” when save the IP
policyrouting configuration use CI command.
Problem Condition: It will show “the flags is: 0x00000007” when save the IP
policyrouting configuration use CI command.
11. [BUG FIX] SPRID: 060116808
Problem Symptom: Issue CI command “sys stdio 0”,then issue CI command “exit”, the
DUT will hang
Problem Condition: Issue CI command “sys stdio 0”,then issue CI command “exit”,
the DUT will hang
12. [BUG FIX] SPRID: 060116809
Problem Symptom: Type 29 characters, and then click “Generate”, the DUT will crash.
Problem Condition: Step1. login GUI-＞Wireless LAN page, select the Security mode
= Static WEP, in Passphase, type 29 characters, then click the “Generate”.
Step2. the DUT will crash.