ZyXEL Communications P-2612HNU-Fx Series User manual

www.zyxel.com
802.11n ADSL2+ VoIP IAD
Firmware V3.00
Edition 1, 1/2010
P-2612HNU-Fx
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Login: User Name: user
Password: 1234
Administrator
Login: User Name: admin Password: 1234
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
WLAN
BUTTON
POWER
LED DSL
LED
INTERNET
LED
PHONE 1, 2
ON/OFF
RESET
POWER
ETHERNET
PORTS
LEDS
WAN
LED
WLAN
LED
ETHERNET
LED
PHONE
PORTS
DSL/WAN
WAN
PORT
DSL
PORT
USB
LED
USB
PORTS

3
Overview
The P-2612HNU-Fx is an ADSL Integrated Access Device (IAD) which
combines high-speed ADSL Internet access, a built-in switch, a firewall
and high-speed wireless networking capability. It also has a USB 2.0 port
for sharing files via a USB compatible storage device and two phone
ports for making calls over the Internet (Voice over IP or VoIP). The P-
2612HNU-Fx can also function as a print server.
Requirements
Make sure you have the following things before you start.
• Internet access - account information provided by your ISP, such as
user name, password, and so on.
• VoIP account - You need the account information provided by your
VoIP service provider (the company that lets you make phone calls
over the Internet).

4
• Internet Explorer 6.0 or later or Netscape Navigator 7.0 or later, with
JavaScript enabled.
See the User’s Guide on the CD for all configuration details including
setting up a shared printer.
Hardware Connections
Remove the P-2612HNU-Fx’s plastic cover before using it.

5
1. Do one of the following for your Internet connection:
a. DSL: Use a telephone wire to connect this port to a telephone jack
(or the DSL or MODEM jack on a splitter, if you have one).
b. WAN: If you have a DSL router or modem already in your network
or you want to use a cable modem, push the DSL/WAN switch to
the WAN side and use an Ethernet cable to connect this port to an
Ethernet jack with Internet access.
2. ETHERNET: Use an Ethernet cable to connect a computer to one of
these ports for initial configuration and/or Internet access.
3. USB 2.0: Connect a USB (version 2.0 or lower) memory stick or a
USB hard drive for file sharing. The P-2612HNU-Fx automatically
detects the USB device. Alternatively, use a USB cable (not
provided) to connect a USB (version 2.0 or lower) printer to this
port.
4. PHONE: Use a telephone cable (and any telephone adaptor provided
with your P-2612HNU-Fx) to connect a telephone to the PHONE 1 or
PHONE 2 port. If you only have one telephone, you should use port 1.
5. Use the power adaptor provided with your P-2612HNU-Fx to connect
an appropriate power source to this socket.
6. Push the power button to the on position.
Look at the LEDs (lights) on the top panel of the P-2612HNU-Fx.

6
• The POWER light blinks during start-up and is green once the P-
2612HNU-Fx is ready.
• An ETHERNET light turns on if the corresponding ETHERNET port
is properly connected. An Ethernet port’s light blinks when the P-
2612HNU-Fx is sending or receiving data through it.
• The WLAN light stays green when the wireless LAN is ready. It
blinks when the P-2612HNU-Fx is sending/receiving data through
the wireless LAN.
• The DSL light stays on if a physical DSL connection exists and
blinks when transmitting data.
The WAN light stays on if this port is properly connected and blinks
when transmitting data.
The INTERNET light is green when Internet access is available.
• The PHONE lights stay on when your SIP account is registered and
they blink if the receiver is off the hook.
• The USB light turns on when there is a USB device (printer or
memory stick) connected to the P-2612HNU-Fx and blinks when
transmitting data.
 If no lights are on, check your connections. Make sure that
you have the power adaptor connected to the P-2612HNU-
Fx and plugged in to an appropriate power source. Make
sure the power source is turned on. Turn the P-2612HNU-Fx
off, wait for a few seconds and turn it back on. If the LEDs
are still off, contact your local vendor.

7
Log into the Web Configurator
1. Open your browser and enter http://192.168.1.1 (the P-2612HNU-
Fx's default IP address) as the address.
2. For administrator login, enter username admin and password 1234
(default). Only administrators can configure the SIP account settings.
For user login, enter user as the username and 1234 as the
password. Click Login.
 If the login screen does not open, make sure you allow web
browser pop-up windows, JavaScripts and Java
permissions. Your computer should be also set to get an IP
address automatically from a DHCP server. See the
appendices in your User’s Guide for more information.
See your User's Guide for how to use the VoIP > SIP screen to set up
your VoIP account if the INTERNET light is green but the PHONE light is
off.
If the PHONE light is on, skip to Using Your Phones on page 13 to see
how to make calls through the Internet.

8
See your User’s Guide for how to use the Network > WAN screen to set
up the WAN connection:
• If the DSL/WAN switch is set to DSL and the DSL light is on but
the INTERNET light is off.
• If the DSL/WAN switch set to WAN and the WAN light is on but
the INTERNET light is off.
Set Up a Wireless Network
To set up a wireless network you need at least one wireless network
card/adapter.
• If you have a desktop computer, use either a wireless USB adapter
or a wireless PCI adapter.
• If you have a laptop, use either a wireless USB adapter or a
wireless CardBus card. These are built into many laptops.
Setting Up a Wireless Network with WPS
If your wireless devices display the WPS logo, you
can use Wi-Fi Protected Setup (WPS) to add
wireless devices to your wireless network. If your
wireless devices do not display the WPS logo, go to
Set Up a Wireless Network Manually on page 11 to manually set up a
wireless network.
The P-2612HNU-Fx supports two WPS methods for creating a secure
connection.

9
• Push Button Configuration - create a secure wireless network
simply by pressing the P-2612HNU-Fx’s physical WPS button. See
Push Button Configuration on page 9.
• PIN Configuration - create a secure wireless network by entering
your wireless device’s PIN (Personal Identification Number) into the
configuration screen of the P-2612HNU-Fx. See PIN Configuration
on page 10.
You must use the same method on the P-2612HNU-Fx and the wireless
client.
Push Button Configuration
1. Place a WPS-enabled device that is installed in your system and
supports the WPS Push Button method within range of the P-
2612HNU-Fx.
2. Press the WLAN button on the P-2612HNU-Fx’s top panel for five
seconds.
3. Use the WPS-enabled device’s WPS button. It can be either a button
in the utility or a physical button. See the device’s documentation if
you cannot locate the WPS button. It doesn’t matter which button is
pressed first. You must press the second button within two minutes of
pressing the first one.
4. The P-2612HNU-Fx and the wireless device establish a secure
connection. This can take up to two minutes.

10
5. Congratulations! Your computer is now ready to connect to the
Internet wirelessly through your P-2612HNU-Fx.
PIN Configuration
1. Place a WPS-enabled device that is installed in your computer and
supports the WPS PIN configuration method within range of the P-
2612HNU-Fx.
2. Log into the P-2612HNU-Fx’s web configurator at http://192.168.1.1
(see Log into the Web Configurator on page 7for more details on
this).
3. In the Status screen click Network in the left panel then click
Wireless LAN. In the Wireless LAN screen click the WPS tab.

11
4. Enter the PIN of the other WPS-enabled device into the Input
Station’s PIN number text box and click Start. You can locate this
PIN number in the other device’s utility or on the device itself. See the
other device’s documentation if you cannot locate the PIN.
5. Click Start or Apply in the other device’s utility screen within two
minutes of clicking Start in the P-2612HNU-Fx web configurator
screen.
6. The P-2612HNU-Fx and the other WPS-enabled device establish a
secure connection. This can take up to two minutes.
7. Congratulations! Your computer is now ready to connect to the
Internet wirelessly through your P-2612HNU-Fx.

12
Set Up a Wireless Network Manually
Configure wireless devices to use the same wireless settings as the P-
2612HNU-Fx. If you didn’t configure the P-2612HNU-Fx’s wireless
settings, use the wireless SSID (network name) and WPA-PSK
encryption key on the P-2612HNU-Fx’s rear panel. The connection
procedure is shown here using Windows XP as an example.
1. Right-click the wireless adapter icon which appears in the bottom
right of your computer monitor. Click View Available Wireless
Networks.
2. Select the P-2612HNU-Fx’s SSID name and click Connect (A). The
SSID “SecureWirelessNetwork” is given here as an example.
A

13
3. You are prompted to enter a password. Enter it and click Connect.
4. You may have to wait several minutes while your computer connects
to the wireless network.
5. You should now be securely connected wirelessly to the P-2612HNU-
Fx.
Congratulations! Your computer is now ready to connect to the Internet
wirelessly through your P-2612HNU-Fx.
 If you cannot connect wirelessly to the P-2612HNU-Fx,
check you have selected the correct SSID and entered the
correct security key. If that does not work, ensure your
wireless network adapter is enabled by clicking on the
wireless adapter icon and clicking Enable. See the User’s
Guide for more suggestions.
Using Your Phones
Follow these directions to make calls over the Internet.

14
• To dial a SIP number that only uses numbers (for example,
“12345”), dial the number on your phone’s keypad. You can also
set up a speed-dial entry, if you want. See the User’s Guide for
instructions.
• To dial a SIP number that uses letters, set up a speed-dial entry
first. See the User’s Guide for instructions. Then, dial the speed-dial
number to make the call.
• To call regular telephone numbers, use your VoIP service
provider’s dialing plan.
• For call forward service, contact your service provider to know if
they support this feature.
European Flash Key Commands
Command Sub-
command Description
Flash Put a current call on hold to place a second call.
Switch back to the call (if there is no second call).
Flash 0 Drop the call presently on hold or reject an incoming call
which is waiting for answer.
Flash 1 Disconnect the current phone connection and answer
the incoming call or resume with caller presently on
hold.
Flash 2 1. Switch back and forth between two calls.
2. Put a current call on hold to answer an incoming call.
3. Separate the current three-way conference call into
two individual calls (one is on-line, the other is on hold).
Flash 3 Create three-way conference connection.
Flash *98# Transfer the call to another phone.

15
Phone Functions Summary
Keys Function Description
*98# Call transfer Transfer a call to another phone.
*92# Call return Place a call to the last person who called you.
*95# Enable Do
Not Disturb Use these to set your phone not to ring when someone calls you, or to turn this function off.
#95# Disable Do
Not Disturb
*43# Enable call
waiting Use these to allow you to put a call on hold while answering another, or to turn this function off.
#43# Disable call
waiting
*21* Uncondition
Forward
Activate
Forward all incoming calls. This feature must be supported
by your service provider before it can be enabled.
#21# Uncondition
Forward
Deactivate
Disable forwarding for incoming calls.
*61* No Answer
Forward
Activate
Forward incoming calls if you do not answer. This feature
must be supported by your service provider before it can be
enabled.
#61# No Answer
Forward
Deactivate
Disable forwarding for incoming calls if you do not answer.
*67* Busy
Forward
Activate
Forward calls if you are already making a call. This feature
must be supported by your service provider before it can be
enabled.
#67# Busy
Forward
Deactivate
Disable forwarding incoming calls if you are already making
a call.

16
To call into the phone that is attached to the P-2612HNU-Fx, use your
VoIP service provider’s dialing plan.
USB File Sharing
This section shows you how to enable USB file sharing. In order to start
file sharing you need to:
• Connect your USB 2.0 file sharing device. See Hardware
Connections.
• Enable the file sharing feature.
• Create an account (user name and password) for sharing the files.
• Browse to your files using the IP address of the P-2612HNU-Fx.
Configure USB File Sharing
1. Click Advanced > File Sharing.
#31# One Shot
Caller ID
Display
Activate call waiting on the next call only.
*31* One Shot
Caller ID
Hidden
Deactivate call waiting on the next call only.
Keys Function Description

17
2. Check the box Enable File Sharing Services and click Apply.
The P-2612HNU-Fx automatically recognizes the USB device which is
connected to the USB port and makes it available for sharing (shown in
the figure above).
Browse to the USB File Share
1. In Windows
Explorer’s
Address bar
type a double
backslash “\\”
followed by
the IP address
of the P-
2612HNU-Fx
(192.168.1.1is
the default)
and hit
[ENTER].

18
2. Enter the user name and password in the window prompt that
appears and hit OK.
3. The files on the USB file sharing device connected to the P-
2612HNU-Fx are now part of your file structure and you can manage
those files just like any other files on your computer.
Refer to the User’s Guide for a complete description of this feature.
Viewing Your Product’s Certifications
1. Go to www.zyxel.com.
2. Select your product from the drop-down list box on the ZyXEL home
page to go to that product's page.
3. Select the certification you wish to view from this page.