ZyXEL Communications ADSL2+ Ethernet / USB Router P-660RU-Tx v2 User manual

P-660RU-Tx v2
ADSL2+ Ethernet / USB Router
Quick Start Guide
Version 3.40
Edition 4
10/2008

1
P-660RU-Tx v2 Quick Start Guide
Overview
The P-660RU-Tx v2 is an ADSL router with both USB and
Ethernet ports.
See your User’s Guide for background information on all
features.
This Quick Start Guide shows you how to:
• Connect the hardware.
• Set up your Internet connection. Be sure you have your
Internet connection information from your Internet Service
Provider (ISP) to set up the connection (See section 2).
How to use the included CD
If you prefer to see a multi-media animation of how to make
hardware connections, see the installation tutorial on the
included CD.
1On the included CD, click Multimedia Auto Provisioner >
Installation Tutorial.
2At the end of the tutorial, click Configuration Genie to set
up your P-660RU-Tx v2 to connect to the Internet.

P-660RU-Tx v2 Quick Start Guide
2
1 Hardware Connections
There are two ways to connect your computer or computer
network to the P-660RU-Tx v2:
Option A: Connect via Ethernet. See page 2.
Option B: Connect via USB (you will need to install the USB
driver). See page 4.
Option A: Connect via Ethernet
1ETHERNET: Use the yellow Ethernet cable to connect a
computer to the ETHERNET port for initial configuration
and/or Internet access.

3
P-660RU-Tx v2 Quick Start Guide
2DSL: Use the gray telephone wire to connect your P-
660RU-Tx v2’s DSL port to a telephone jack (or to a
splitter, if one is already installed).
3POWER: Use the power adaptor provided with your P-
660RU-Tx v2 to connect an appropriate power source to
the POWER socket. Make sure the power source is on.
4Push in the POWER button.
5Look at the lights on the front panel.
• The light blinks while your P-660RU-Tx v2 starts up and
stays on once it is ready.
•The light is on when the P-660RU-Tx v2 has a DSL con-
nection.
• The light is on when you are able to access the Internet
and blinks when the P-660RU-Tx v2 is sending or receiving
data.
• The light stays on if the corresponding ETHERNET port
is properly connected and blinks when there is traffic.

P-660RU-Tx v2 Quick Start Guide
4
VIf any of these lights are not on, check your
connections and inspect your cables for
damage. If the lights are still off, contact your
local vendor.
Option B: Connect via USB

5
P-660RU-Tx v2 Quick Start Guide
"Do NOT connect the same computer to both the
USB and ETHERNET ports on the P-660RU-Tx
v2.
1USB:Connect the provided USB cable to the P-660RU-Tx
v2’s USB port.
2DSL: Use the gray telephone wire to connect your P-
660RU-Tx v2’s DSL port to a telephone jack (or to a
splitter, if one is already installed).
3POWER: Use the power adaptor provided with your P-
660RU-Tx v2 to connect an appropriate power source to
the POWER socket. Make sure the power source is on.
4Push in the POWER button.
5Look at the lights on the front panel.
• The light blinks while your P-660RU-Tx v2 starts up and
stays on once it is ready.
•The light is on when the P-660RU-Tx v2 has a DSL con-
nection.

P-660RU-Tx v2 Quick Start Guide
6
• The light turns on if the USB port is properly connected,
and blinks when there is traffic.
VIf any of these lights are not on, check your
connections and inspect your cables for
damage. If the lights are still off, contact your
local vendor.
Install the USB Software
If you want to connect to the Internet through the P-660RU-Tx
v2's USB port, install the USB driver before you connect the
P-660RU-Tx v2 to the USB port. Follow the steps for your
operating system to install the USB driver.
Windows Computer
System Requirements
• Windows 98 SE (Second Edition), Windows ME (Millennium
Edition), Windows 2000, Windows XP, or Windows Vista
• An available USB port
Procedures
1Save your work and close all applications.
2Insert the included CD. The CD automatically runs and the
main screen displays.

7
P-660RU-Tx v2 Quick Start Guide
3Click the Setup icon on the main screen.
4Select the Windows version of your computer.
5An install warning may appear in the Windows Vista OS.
Click Allow to continue.
6Click Next in the Welcome screen to begin the USB
Installation Wizard. Follow the installation prompts. You
may need to restart your computer at the end of the
installation.

P-660RU-Tx v2 Quick Start Guide
8
Macintosh Computer
System Requirements
• Macintosh operating system versions 10.1, 10.2 and 10.3.
• An available USB port
Procedures
1Save your work and close all applications.
2Insert the included CD. A CD’s icon automatically
displays on the desktop.
3Double-click the CD's icon.
4Double-click the MAC version of your computer.

9
P-660RU-Tx v2 Quick Start Guide
5Double-click one of the following.
If you selected MAC10.1, double click the P-660RU-T icon.
If you selected MAC 10.2_10.3, double click the P-660RU-
Tx.dmg icon.