ZyXEL Communications P-792H Instruction Manual

ZyXEL Confidential
ZyXEL
Firmware Release Note
P792H
Standard version
Release 3.40(BZ.3)C0
Date: Nov 03, 2006
Author: Rongrong Guo
1/27

ZyXEL Confidential
ZyXEL P792H Standard Version
release 3.40(BZ.3)C0
Release Note
Date: Nov 03, 2006
Supported Platforms:
ZyXEL P792H
Versions:
ZyNOS Version: V3.40(BZ.3) | 11/03/2006 16:00:00
Bootbase Version: V1.14 | 11/10/2003 20:56:40
Notes:
Support Globespan modem code A.423.
Features:
Modifications in V3.40(BZ.3)C0 | 11/03/2006 16:00:00
1. Change to FCS.
Modifications in V3.40(BZ.3)b2 | 10/25/2006 10:00:00
1. [FEATURE ENHANCE] Add MTU
2. [FEATURE ENHANCE] Multi Routing Mode dynamic PVC support
3. [FEATURE ENHANCE] IPPR V2 support to forward the traffic by
remote node(PVC)instead of gateway IP Address
4. [BUG FIX]
SPRID:060727813
Symptom: Content filter schedule can’t be canceled
Condition: Step 1.Enable keyword blocking and edit key words. Step2. Enter Schedule
page and unselect all check boxes. Step3. The web site in the key words list also can
be blocked.
5. [BUG FIX]
SPRID: 060727816
Symptom/Condition: Throughput in route mode downstream can’t pass PQA criteria
with IES5000 DSLAM. (Throughput with IES5000 SHDSL DSLAM is much worse
than it with IES1000 SHDSL DSLAM).
6. [BUG FIX]
SPRID:060727807
Symptom: Release note is not correct
Condition: FW version in Menu 24.2.1 shows V3.40(BZ.2)|10/11/2005
2/27

ZyXEL Confidential
Modifications in V3.40(BZ.3)b1 | 02/28/2006 09:32:11
1. [FEATURE ENHANCE] Add Cone NAT .
2. [FEATURE ENHANCE] Add VPN NAT TRAVERSAL.
3. [BUG FIX]
SPRID: 060301057
Symptom: In GUI/smt, when choosing WAN backup mechanism as DSL Line, you
have to key in one check WANIP which is not reasonable.
Condition:N/A
4. [BUG FIX]
SPRID: 060301060
Symptom: If you enter one check WANIP, even the backup mechanism is “DSL Link”,
P792H will also ping that IP address periodically.
Condition: N/A
5. [BUG FIX]
SPRID: 060301061
Symptom: Open its WEB GUI with 192.168.1.1,in “advanced setup” list, there is a
option “logs”. When we click it, we can only get a wrong page of “the page cannot be
found” each time.
Condition: N/A
Modifications in V3.40(BZ.2) | 10/11/2005 10:32:11
1. Change to FCS
Modifications in V3.40(BZ.2)b2 | 09/23/2005 15:32:11
1. [BUG FIXED] 050914568
Symptom: The IP routing Policy don＇t work properly
Condition: step1 Setup one IP routing Policy rule (in SMT 25),If traffic matches ippr
rule, traffic will go out through appointed gateway, but failed
Modifications in V3.40(BZ.2)b1 | 09/07/2005 15:32:11
1. [FEATURE CHANGED] Add feature MBM.
2. [FEATURE CHANGED] Add port based VLAN.
3. [BUG FIXED] 050909370
Symptom& Condition: Key in”http://192.168.1.1/rpFWUpload.html”in IE, can login
in Firmware page without user name and password, then user can do romreset and
upload new firmware.
4. [BUG FIXED] 050909373
Symptom: Traffic redirect function cannot work properly at ENET-ENCAP with static
setting.
Condition: In menu 4 when using ENET ENCAP encapsulation and set static address.
In menu 2, we set a traffic redirect function, it could not work properly.
5. [BUG FIXED] 050909374
Symptom: The GUI\Wizard Setup can save the no match IP.
Condition: While set the DUT LAN “Client IP Pool Starting Address” and “Size of
Client IP Pool” which are not match the “IP Subnet Mask”, but this can be saved in
GUI\Wizard Setup and rom-t. In SMT and GUI\Advanced Setup have no this issue.
6. [BUG FIXED] 050909375
Symptom: if we change remode IP address or gateway in menu 4 or menu11, the
3/27

ZyXEL Confidential
previous routing entry still keep. it can see in CI command:ip route status.
Condition: In menu4 or menu11,Configure Enet Encap=static IP, then change to
PPPoE dynamic, in menu24.8, check the route table, the Enet Encap entry still
existed.unless you restart the DUT.
7. [BUG FIXED] 050909376
Symptom: After save DNS server, In CI command: ip ping www.hinet.net, it can not
be work and it must reboot.
Condition: We save DNS server in menu 3.2 after reset default rom file and if we don’t
reset system and issue ”ip ping www.hinet.net” that it can not be work and it must
reboot.
8. [BUG FIXED] 050909377
Symptom: When DUT use static IP and set DNS server address in GUI->wizard, DUT
won’t resolve domain name successfully until reboot
Condition: Step1 Go to GUI, configure DUT use static IP and set DNS server, then go
to Maintenance->Diagnostic, try to resolve domain name, but failed; Step2 Reboot
DUT, it works fine; Step3 This many cause TMSS/AV/CAC/DDNS functions doesn’t
work for these functions need DUT resolve domain name.
9. [BUG FIXED] 050909378
Symptom& Condition: enter eWC NAT, click the edit detail of full feature will apply
full feature.
10. [BUG FIXED] 050909379
Symptom& Condition: While delete menu4, then go to GUI to change NAT mode and
then apply in GUI, then go to SMT menu 24.1will cause crash.
11. [BUG FIXED] 050909380
Symptom: PPPOE nailed-up work have problem
Condition: Step1 use PPPOE and nailed-it up; Step2 in SMT menu 26.1 set a schedule
start time 00:03 and duration time is 00:02 and force down; Step3 in menu11.1
schedule set =1, now time is 00:02 when time is 00:03 then PPPOE turn down, but time
is 00:05 the PPPOE can not turn up, then in menu 24.8 command “d d 1” still can not
turn up.
Modifications in V3.40(BZ.1)C0 | 6/28/2005 13:32:11
1. [FEATURE CHANGED] Change to FCS.
Modifications in V3.40(BZ.1)b3 | 6/22/2005 9:53:09
1. [FEATURE CHANGED] Support new modem code A.423.
Modifications in V3.40(BZ.1)b2 | 3/28/2005 9:09:08
1. [FEATURE CHANGED] Support new modem code R3.0.1
2. [FEATURE CHANGED] Support new MAC, atwz , sys atwz command
3. [FEATURE CHANGED] Change hw version to 1 in bootbase , and after we change
AFE , this f/w can support new hardware and old hardware.
4/27

ZyXEL Confidential
Modifications in V 3.40(BZ.1)b1 | 04/07/2004
1. [BUG FIXED]
Symptom: User name/Password have one space at eWC.
Condition: Restore to default ROM file and chage to PPPoA/PPPoE mode, there is one
space at User name/Password field at eWC.
Modifications in V 3.40(BZ.0)C0 | 03/12/2004
1. Change to FCS version
Modifications in V 3.40(BZ.0)b2 | 03/05/2004
1. [FEATURE ENHANCED]
Support SIP pass-through.
Modifications in V 3.40(BZ.0)b1 | 01/07/2004
1. Create Project.
2. [FEATURE ENHANCED]
Support Wan Backup.
3. [FEATURE ENHANCED]
Support Firewall and Content Filter.
4. [FEATURE ENHANCED]
Support VPN
5. [FEATURE ENHANCED]
Support H.323v2 for NAT.ALG
5/27

ZyXEL Confidential
Annex A CI Command List
Command Class List Table
System Related Command Exit Command Ethernet Related Command
WAN Related Command IP Related Command Bridge Related Command
XDSL Related Command
SystemRelatedCommand Home
Command Description
sys
adjtime retrive date and time from Internet
atsh display MRD field
callhist
display display call history
remove <index> remove entry from call history
countrycode [countrycode] set country code
date [year month date] set/display date
domainname display domain name
edit <filename> edit a text file
extraphnum maintain extra phone numbers for outcalls
add <set 1-3> <1st phone num> [2nd phone
num] add extra phone numbers
display display extra phone numbers
node <num> set all extend phone number to remote node
<num>
remove <set 1-3> remove extra phone numbers
reset reset flag and mask
feature display feature bit
hostname [hostname] display system hostname
log
clear clear log error
disp display log error
online [on|off] turn on/off error log online display
stdio [second] change terminal timeout value
time [hour [min [sec]]] display/set system time
trcdisp parse, brief, disp monitor packets
syslog
server [destIP] set syslog server IP address
facility <FacilityNo> set syslog facility
type [type] set/display syslog type flag
mode [on|off] set syslog mode
version display RAS code and driver version
view <filename> view a text file
wdog
switch [on|off] set on/off wdog
cnt [value] display watchdog counts value: 0-34463
romreset restore default romfile
socket display system socket information
ddns
debug <level> enable/disable ddns service
display <iface name> display ddns information
restart <iface name> restart ddns
logout <iface name> logout ddns
6/27

ZyXEL Confidential
cpu
display display CPU utilization
xmodemmo
de [crc|checksum] select xmodem mode
ExitCommand Home
Command Description
exit exit smt menu
Ethernet Related Command Home
Command Description
ether
config display LAN configuration information
driver
Cnt
disp <name> display ether driver counters
Status <ch_name> see LAN status
config [0|1=auto|normal] [0|1=10|100]
[0|1=HD|FD] <ch-name> Configure LAN Settings Auto/Normal, 100/10 Mbps, Half/Full Duplex
version see ethernet device type
WANRelatedCommand Home
Command Description
Wan atm test [fix|rand|period|oam|loopback] Generate ATM traffic
hwsar Disp Display hwsar packets incoming/outgoing
information
Clear Clear hwsar packets information
Sendoam Send OAM packets: <vpi> <vci> <f5>
<end-to-end> <type:0(AIS) 1(RDI)
2(LoopBack)>
IPRelatedCommand Home
Command Description
ip
address [addr] display host ip address
alias <iface> alias iface
aliasdis <0|1> disable alias
arp
status <iface> display ip arp status
dhcp <iface>
client
release release DHCP client IP
renew renew DHCP client IP
status [option] show dhcp status
dns
query
stats
clear clear dns statistics
disp display dns statistics
icmp
status display icmp statistic counter
discovery <iface> [on|off] set icmp router discovery flag
ifconfig [iface] [ipaddr] [broadcast <addr>
|mtu <value>|dynamic] configure network interface
7/27

ZyXEL Confidential
ping <hostid> ping remote host
route
status [if] display routing table
add <dest_addr|default>[/<bits>]
<gateway> [<metric>] add route
addiface <dest_addr|default>[/<bits>]
<gateway> [<metric>] add an entry to the routing table to iface
addprivate <dest_addr|default>[/<bits>]
<gateway> [<metric>] add private route
drop <host addr> [/<bits>] drop a route
status display ip statistic counters
udp
status display udp status
tcp
status [tcb] [<interval>] display TCP statistic counters
xparent
join <iface1> [<iface2>] join iface2 to iface1 group
break <iface> break iface to leave ipxparent group
igmp
debug [level] set igmp debug level
forwardall [on|off] turn on/off igmp forward to all interfaces flag
querier [on|off] turn on/off igmp stop query flag
iface
<iface> grouptm <timeout> set igmp group timeout
<iface> interval <interval> set igmp query interval
<iface> join <group> join a group on iface
<iface> leave <group> leave a group on iface
<iface> query send query on iface
<iface> rsptime [time] set igmp response time
<iface> start turn on of igmp on iface
<iface> stop turn off of igmp on iface
<iface> ttl <threshold> set ttl threshold
<iface> v1compat [on|off] turn on/off v1compat on iface
robustness <num> set igmp robustness variable
status dump igmp status
BridgeRelatedCommand Home
Command Description
bridge
cnt related to bridge routing statistic table
disp display bridge route counter
clear clear bridge route counter
stat related to bridge packet statistic table
disp display bridge route packet counter
clear clear bridge route packet counter
XDSLRelatedCommand Home
Command Description
xdsl
state display XDSL status about physical layer
restart restart XDSL driver
cnt disp display xdsl error counter
clear clear xdsl error counter
8/27

ZyXEL Confidential
Internal Information:
1. Modification.
Modifications in V 3.40(BZ.1)b1 | 04/07/2004
1. [FEATURE CHANGED]
Modify the way of LED display for HTP test and always not to display UART External
Loopback test item.
(1) normal case: SYS LED blinking per 1 second.
(2) SYS LED always on.
Modifications in V 3.40(BZ.0)b2 | 03/05/2004
1. [BUG FIXED]
Symptom: In VPN-Summary, the content of rules number greater than 5 are not
updated.
Condition: 1. Configure VPN rule 6 & save
2. Delete VPN rule 6
3. In VPN-Summary page, rule 6 still exist.
2. [BUG FIXED]
Symptom: CI-command "ip smtp sendmail" cause device reboot.
Condition: Type CI-command "ip smtp sendmail" will cause device reboot.
3. [BUG FIXED]
Symptom: Not update DNS information.
Condition: If ISP assigns different DNS after PPP connection, the device will
not update the DNS information.
4. [BUG FIXED]
Symptom: qlm error or traffic is blocked
Condition: qlm error bug:
1). Setup 2 remote node, node 1 is RFC-1483 bridge mode.node 2 is
routing mode with PPPoE nailed-up.
2). Actuality, node 2 just there and do nothing.
3). Heavy traffic through our device will cause qlm error.
Modifications in V 3.40(BZ.0)b1 | 01/07/2004
1. [FEATURE CHANGED]
Enlarge Rom File to 48K byte.
Known Issues:
1. AX/4000 will occur PRBS Bit Error Count.
2. Manufactory Data in Bootbase
9/27

ZyXEL Confidential
ZyNOS Version : V3.40(BZ.3) | 11/03/2006 16:00:00
Bootbase Version : V1.14 | 11/10/2003 20:56:40
Vendor Name : ZyXEL Communications Corp.
Product Model : Prestige 792H
ZyNOS Code Model : P792H STU-R
HTP Code Model : HTP_P792H V 0.2
ZyNOS ROM address : bfc10000
System Type : 7
MAC Address : 001349000001
Default Country Code : FF
Boot Module Debug Flag : 01
RomFile Version : 3A
RomFile Checksum : 6f66
ZyNOS Checksum : 4fae
Core Checksum : 73f7
SNMP MIB level & OID : 060102030405060708091011121314151617181920
Main Feature Bits : 86
Other Feature Bits :
92 3B 00 00 01 00 00 00-00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00-02 00 13 00 00 00
Notes:
•Debug Flag should be 0 after production. In our default release will be 1. Because in the
manufacture process will need it to set the MAC address.
•MAC address will be changed by production process. Only the fist 3 octets will be correct. The last
3 octets will depend on the production process.
3. Default ROM File Value Setting
·Menu 1: General Setup
Menu 1 - General Setup
System Name= ?
Location=
Contact Person's Name=
Domain Name=
Edit Dynamic DNS= No
Route IP= Yes
Bridge= No
Press ENTER to Confirm or ESC to Cancel:
·Menu 1.1: Configure Dynamic DNS
Menu 1.1 – Configure Dynamic DNS
Service Provider= WWW.DynDNS.ORG
Active= No
Host=
10/27