ZyXEL Communications ES-315-F - QUICK GUIDE V3.70 User manual

Copyright © 2007. All rights reserved
ES-315-F
Intelligent Layer 2 Managed Switch
Quick Start Guide
Version 3.70
7/2007
Edition 1
DEFAULT LOGIN
IP Address http://192.168.1.1
Username admin
Password 1234

ES-315-F Quick Start Guide
1
1 Overview
Your ES-315-F is an intelligent layer-2 Ethernet switch with
four Fast Ethernet RJ-45 ports and one Fast Ethernet Small
Form-factor Pluggable slot. Use the ES-315-F to connect up
to four Ethernet devices to your network. The following
example shows your ES-315-F (A) connecting several
devices (1~ 4) and allowing them to communicate with one
another and access the Internet through the Internet Service
Provider’s network switch (B).
This Quick Start Guide shows you how to do the following:
Make Hardware Connections on page 2.
Log In To the Web Configurator on page 14.
Set the Password on page 16.
Set Up Your Network on page 18.
Wall-mount the ES-315-F on page 22.

2
ES-315-F Quick Start Guide
2 Make Hardware Connections
2.1 Connect the WAN
To make the ES-315-F’s fiber-optic connection you need to:
1Open the ES-315-F.
2Install an SFP transceiver.
3Attach the wire mounts.
4Insert a fiber-optic cable through a bushing and wrap it
around the wire mounts.
5Connect the fiber-optic cable to the SFP transceiver.
"Only qualified technicians should perform these
actions!
2.1.1 Open the ES-315-F
1Remove both screws from the housing.

ES-315-F Quick Start Guide
3
2Lift the cover.
2.1.2 Install A Transceiver
The ES-315-F supports MSA (Multi-Source Agreement)
compliant SFP transceivers. Inside the ES-315-F, there is a
slot for an SFP transceiver with an LC-type connector.
Please observe the following warnings when working with
transceivers.
• Only trained and qualified personnel should install or replace
transceivers.
• SFP transceivers are sensitive to static. To prevent damage
from electrostatic discharge (ESD), use an ESD preventive
wrist strap when you install or remove a SFP transceiver.
• Avoid getting dust and other contaminants into the optical
bores.

4
ES-315-F Quick Start Guide
• SFP transceivers are equipped with a Class 1 laser, which
emits invisible radiation when the device or system is pow-
ered up. To avoid possible eye injury, do not look into an
operating fiber-optic transceiver’s connectors.
• Do not remove and install an SFP transceiver more often
than is absolutely necessary. Doing so may shorten the use-
ful life of the transceiver.
Take the following steps to attach a transceiver.
1Disconnect all fiber-optic cables from an SFP transceiver
before installing or removing it.
2Remove the SFP transceiver from its protective
packaging.
3Align the SFP transceiver in front of the SFP slot opening.

ES-315-F Quick Start Guide
5
4Insert the SFP transceiver into the slot until it snaps into
place.
"Your SFP transceiver has a mechanism that
prevents incorrect insertion. Do NOT force or
twist the SFP transceiver into a slot.
5Lock the transceiver into place (if your transceiver has a
locking mechanism).
"See the transceiver’s User’s Guide for more
information.

6
ES-315-F Quick Start Guide
2.1.3 Install Fiber-optic Cable
Follow these procedures to install the fiber-optic cable.
Attach Wire Mounts
Remove the adhesive cover from the wire mounts and attach
them to the sides of the ES-315-F.
Insert Fiber-optic Cable
The ES-315-F has holes (labelled Ain the following figure)
through which you can insert fiber-optic cable.
1Insert a bushing into a hole through which you will insert
the fiber-optic cable.
2Create a hole in the bushing and thread the fiber-optic
cable through it.

ES-315-F Quick Start Guide
7
3Insert bushings into the remaining vacant holes to cover
them.
4Coil excess fiber-optic cable around the inside of the ES-
315-F using the wire mounts as shown in the following
figure.
Connect The Fiber-optic Cable To The Transceiver
1Remove the dust plugs from the SFP transceiver and the
cables.
AA
A
A

8
ES-315-F Quick Start Guide
2Insert the end of the fiber-optic cable into the SFP
transceiver.
Close the ES-315-F
1Close the cover.

ES-315-F Quick Start Guide
9
2Replace the screws.
2.2 Make LAN and Power Connections
1LAN:Using an Ethernet cable, connect your computer to
one of the LAN ports (1, 2, 3or 4) for initial configuration.