28 GORILLA 28-0010366 User manual

User Manual and User Information.
User Manual and User Information
Model: 28-0010366
28 Gorilla
12 S. San Marcos Place
Chandler, AZ 85225
U.S.A.
https://28gorilla.com
Tel: [phone]
Copyright© 2021 28 Gorilla Engineering. 28 Gorilla Engineering, the 28 Gorilla Engineering
Logo, and other designated brands included herein are trademarks of 28 Gorilla Engineering in
the United States and other countries. All other trademarks are the property of their respective
owners.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL
ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND
RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE
PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST
TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE
SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE
SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE
INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE
SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR 28 GORILLA
REPRESENTATIVE FOR A COPY.
1. Intended Use
1. The purpose of this Charger is to charge receiver equipment outfitted with proprietary energy
receiving circuits. The Charger can only be used in conjunction with devices that contain the
receiving circuits for charging the native batteries of the equipment.
2. If a device that does not contain the proprietary receiver circuits, is placed on the charger. No
charging will ensue and the Charger will not operate.
3. Equipment outfitted with inductive receiver circuits will not charge and the Charger will not
operate.
4. The Charger will only operate once a receiver unit (Rx Unit) is placed on the charging area
directly on top of the charger.
5. Indoor operation only --not to be used in a wet area, metal surface, or outdoors.

User Manual and User Information.
6. This transmitter is designed to specifically used for AE Wireless Temperature Sensor, model: 28-
0010038.
2. User Operation
The charger does not contain a power switch. Simply connect the USB-C cable end to the Charger and the
USB-Type A cable end to the wall adapter power supply. When not charging, the charger is in standby
mode.
In order to charge a receiver, place the receiver equipment in the keyed slot on top of the charger in the
appropriate orientation. The receiver equipment keyed slot should be face down towards the outer edge of
the charger case. When the receiver equipment is placed correctly the top surface of the receiver
equipment should be parallel with the surface of the charger. Once the receiver equipment is placed in the
charger, the charger should commence charging within a few seconds. Consult the equipment’s user
manual for the time duration and procedures for charging.
3. Radio Characteristics:
The WPT transmitter nominal frequency is: 917.5MHz!
The WPT transmitter conducted average output power is: 29 dBm total
The BLE transmitter operating frequency: 2402 – 2480MHz
The BLE transmitter output power: -2.4dBm
4. USB-C Port
Insert the designated USB-C end of the cable into the USB-C port of the charger. Also, place the type A
USB end of the cable to the type A USB port of the electrical AC wall power supply. This will supply
power to the charger used to charge the receiver equipment.
5. Packaging contents
WPT Charging Station
AC Wall Power Supply
USB-C to USB Type A Charger cable
User Manual and User Information

User Manual and User Information.
6. FCC Regulatory Information
FCC ID: 2AX2O-280010320 Model: 28-0010366
This device complies with Part 18 of the FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the equipment being interfered with.
• Increase the separation between the charger and the equipment subject to interference.
• Connect the equipment into an outlet on a circuit different from that to which the charger is
connected.
• Consult the dealer or an experienced radio/TV/electronics technician for help.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
7. RF Exposure Notice
The charger employs receiver equipment proximity sensing. There are no user adjustments and
charging commences only when the internal microcontroller detects valid receiver equipment
and permits commencement of power transfer. After placing your receiver on the charger,
maintain a 2.5cm separation distance to meet applicable requirements.

User Manual and User Information.
8. Supplier’s Declaration of Conformity
Model: 28-0010366
FCC ID: 2AX2O-280010320
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Responsible Party in the USA:
28 Gorilla
12 S. San Marcos Place
Chandler, AZ 85225
U.S.A.