AA Portable Power Corp Smart Charger User manual

User Manual
Of
Smart Charger (15A) for 25.6V (8 cells) LiFePO4
Battery Pack (110V only, Standard Anderson plug)
AA Portable Power Corp (http://www.batteryspace.com)
Address: 860 S, 19th St, Unit A, Richmond, CA, 94804
Tel: [phone]
Fax: [phone]
Email: [email protected]
Prepared & Approved by Louis (01/10/08)

!
Wiring precautions
If failure or error of this instrument could result in a critical
accident of the system, install a external protection circuit to
prevent such an accident.
In order to prevent instrument damage or failure, protect the power
line and the input/output lines from high currents by using fuses with
appropriate ratings.
Power supply
In order to prevent instrument damage or failure, supply power of the
specified rating.
In order to prevent electric shock or instrument failure , do not turn
on the power supply until all of the wiring is completed.
Never use the instrument near inflammable gases
In order to prevent fire, explosion or instrument damage ,never use
this instrument at a location where inflammable or explosive gases or
vapour exist.
Never touch the inside of the instrument
In order to prevent electric shock or burns , never touch the inside
of the instrument .only authorized service engineers can touch the
inside of the instrument to check the circuit or to replace parts. High
voltage and high temperature sections inside the instrument are
extremely dangerous.
Never modify instrument
In order to prevent accident or instrument failure, never modify the
instrument.
Maintenance
In order to prevent electric shock, burns or instrument failure, Only
authorized service engineers may replace parts .In order to use this
instrument continuously and safely, conduct periodic maintenance. Some
parts used in this instrument have a limited service life and may
deteriorate over time.
WARNING

Introduction
AA Portable Power Corp (http://www.batteryspace.com) specialized in
the research & development of the intelligence battery charger in the long
terms.
The series battery charger is based on MCU technology, with pulse
charging mode,the charging voltage has temperature compensation
automatically .It could be used in the various electric cars the field
of tourism, railway, mine, post and telecommunication .
Main Feature
zINPUT
AC input voltage 90 to 130 VAC , single phase
Input frequency 47 to 63 Hz
Efficiency 72%(min)at rating power,115Vac 60Hz
zOUTPUT
CCCV charging mode
Cut-off voltage: 29.6VDC
15A current Max.
Charge terminal: 4' long 8AWG wire 1.9" x 1.5" x 0.6" Standard
Anderson connector
Anderson plug dimension (LxWxH): 1.9"(48.0mm) x
1.5"(38.0mm) x 0.6" (15.0mm)
Included 1 pcs 1.9" x 1.5" x 0.6" Standard Anderson
connector without wire for DIY use.
zTip: In order to match up the charger's connector,You
may connect the battery pack charge terminal
with Included 1 pcs 1.9" x 1.5" x 0.6" Standard
Andersen connector.
z Make sure the charge DIY wire will be acceptable for
15A Max charge current.
zWarning: Wrong polarity will damage the charger, and
Batteryspace are not responsible for the damage
or losses caused by misusing
Note: Anderson connector has no difference in male and
female, which can mate each other
zCHARGE
The Battery range is between 20AH to 40AH
Reverse Polarity Protection
Short Circuit Protection
No trigger voltage requirement
zBuilt in cooling fan to ensure charger long service life
zDimension(LxWxH): 210mm(8.3")x 174mm(6.9") x 76mm(3.0")
zWeight: 5.2lb (2358grams)

How to use
1. Turn on : Make sure the pack voltage is suitable for charger. Then
connect to the pack with correct polarity.
2. Check the voltage of the AC input is suitable for the input voltage
of the charger or not.
3 The charger start ramp charging after auto-testing in 1 minutes
4. Indicating LED signification
5. Power indicating and battery test LED:
Green LED = Fully charged / Correct Polarity Connection
Red LED = Charging / Wrong polarity Connection
Orange LED = 90% fully charged.
6. Turn off: After Battery is fully charged, must disconnect the AC power
supply before disconnect battery
Operation environment
Above the sea-level≤2000m.
Ambient temperature -10℃～50℃
Ambient humidity 5%～70%RH
Storage temperature -10℃～60℃
Without conductive dust
Without explosive dust
Without corrosive gas and steam damaged to metal and isolator
keep away from rain and snow
Mounting slop ≤5 degree
Maintenance and service
The charger must be set at ventilated, dry and dust-less place to
prevent the reduction of the performance of the charger.
For technical support, please contact us via [e-mail].