AA Portable Power Corp Universal Smart Charger User manual

User Manual of
Universal Smart Charger (18A, 29.6V-58.4V Cut-Off) for 36V-
48V SLA , 29.6V-51.8V Li-Ion/LiMnNi (8-14 Cells),38.4V-
51.2V LFP(12-16 Cells) -- CE listed
AA Portable Power Corp (http://www.batteryspace.com)
Address: 860 S, 19th St, Unit A, Richmond, CA, 94804
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Prepared & Approved by Max (09/29/10)

Warning
•Must select AC input voltage correctly before plug to
Wall AC outlet
•Must connect to battery with correct polarity
•Must use with battery pack capacity >= 18Ah
•Must use with SLA (36V-48V, 18-24Cells), Li-
Ion/LiMnNi (29.6V-51.8V, 8-14Cells), LifePO4 (38.4V-
51.2V, 12-16Cells) Battery
•Must select charging voltage correctly based on
battery type/battery voltage used
•We are not responsible for any damage caused by misuse.
•Professional & Indoor use only
•Don't remove the case to prevent from electric shock
•Unplug the charge from AC outlet after use.

Features:
•High Quality Intelligent smart charger (Manufacture part#KP4818CL) designed for
SLA (36V-48V, 18-24Cells), Li-Ion/LiMnNi (29.6V-51.8V, 8-14Cells), LifePO4 (38.4V-
51.2V, 12-16Cells) Battery pack
•Adjustable Charging voltage from 29.6-58.4VDC
•Must select charging voltage correctly based on battery used below
oLi-Ion / LiMnNi = 4.17V / cell
Ex. Charging voltage for 51.8V (14Cells) Li-Ion/LiMnNi =
4.17V x 14 = 58.38V
oLiFePO4 = 3.55V / cell
Ex. Charging voltage for 51.2V (16Cells) LiFePO4 =
3.55V x 16 = 56.8V
oSLA = 2.43V / cell
Ex. Charging voltage for 48V (24Cells) SLA = 2.43 x 24 =
58.32V
•Charging Stage: CC (Constant Current) --> CV (Constant Voltage) --> Floating
•Switch-Mode Technology
oConvert from AC input voltage to DC charging voltage 1677 times faster
than traditional linear charger
oUnit will be smaller, lighter and higher efficiency than traditional linear
charger
•Built in cooling fan to ensure charger long service life
•Input AC power: World-Wide 90-132VAC / 200-240VAC , 47-63Hz, USA AC plug
oFor international use, please click here to order AC plug adaptor
seperately
•Cut-Off Automatically when the battery is fully charge
•Safety protection
oOver Current & Over Voltage protection
oShort Circuit protection
oReverse polarity protection
•Charging Voltage: 29.6-58.4VDC
•Charging Current: 18.0A +/- 0.5A
•Max Power output: 1200W
•Charging time:
oLi-Ion / LiMnNi Charging time = (1.5 x Ah rate of the pack) / charge
current.
oLiFePO4 Charging time = (1.41 x Ah rate of the pack) / charge current.
oSLA Charging time = (1.2 x Ah rate of the pack) / charge current.
•Battery pack Capacity:>= 18Ah
•Stylish Aluminium Enclosure
•Built in 2 unit of LED indicator
oPower ON: LED 1 = Red
oCharging (Constant Current): LED 2 = Red
oCharging (Constant Voltage): LED 2 = Red
oFully charger: LED 2 = Green
•Charging terminal : 4' long 8AWG wire 1.9" x 1.5" x 0.6" Standard Anderson
connector

•Dimension (LxWxH): 260mm(10.2") x 175mm(6.9") x 90(3.5")
•Weight: 9.9 lbs (4.5kg)
•High Efficiency: 85-95%
•MTBF (Mean Time between Failure): 30,000 POH (Power on Hour) = 10 years of
everyday operation of 8 hours
•CE listed
•Operating Temperature: 14F(-10’C) ~ 113F(45’C)
Charging cycle:
If the LED1is ON ( Red ), it shows that input power is ON.
The explanation of the charging cycle is as following.
Stages
Condition Mode Current Voltage LED
Indication
Stage 1
Constant Current
mode CC mode 18A+/-0.5A
To 29.6-58.4V
(Based on
voltage
selection)
Red
Stage 2
Constant Voltage
mode CV mode Reduces from 18A+/-0.5A
Holds at 29.6-
58.4V
(Based on
voltage
selection)
Red
* CC mode = Constant current charge
* CV mode = Constant voltage charge
*** See Stage 2description below
Stage 1: Constant Current Mode (CC):
The charger changes to constant current 18A+/-0.5A. When the
battery voltage reaches up to 29.6-58.4V (Based on voltage selection),
the charging stage changes from CC (Constant Current) to CV
(Constant Voltage) mode.
Stage 2: Constant Voltage Mode (CV):
In this stage the voltage of each cell in the battery is
equalized.The charger holds the battery at 29.6-58.4V (Based on
voltage selection) and the current slowly reduces.

Charging Curve:

Detail Picture
Front View
Note
-MUST Set Charging Voltage CORRECTLY Before
connect to battery.
-Don’t reset charging voltage while charging.
-Wrong charging voltage setting may explode battery.
BatterySpace don’t responsible for any damage from
any miss-use
-57.9VDC Maximum charging voltage can be set after
power turn “On”. To set charging voltage up to
58.4VDC, please connect battery to charger first ,
then warm up charger about 30 minutes
-Charging Current can not be set
-Charging current can be viewed via Charging current
Display switch Position

Back View
Note
- MUST Select AC INPUT Voltage Correctly Before plug to
Wall AC outlet
Note
- For USA customer, MUST SELECT to “115VAC Input
Switch Position”

Connector Detail
Charging Terminal: 1.9" x 1.5" x 0.6" Standard Anderson connector
Included 1 pcs 1.9" x 1.5" x 0.6" Polarity assignment & wire soldering location
Standard Anderson connector for DIY use for Included Standard Anderson
Note:
-Wrong polarity will damage the charger, and Batteryspace
are not responsible for the damage or losses caused by
misusing