ABB Relion 670 series Quick start guide

—
RELION® 670 SERIES
Phasor measurement unit RES670
Version 2.1ANSI
Commissioning manual

Document ID: 1MRK 511 366-UUS
Issued: March 2019
Revision: A
Product version: 2.1
© Copyright 2016 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written permission
from ABB, and the contents thereof must not be imparted to a third party, nor used for any
unauthorized purpose.
The software and hardware described in this document is furnished under a license and may be
used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/) This product includes cryptographic software written/developed by:
Eric Young ([email protected]) and Tim Hudson ([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or other
operational requirements are complied with. In particular, any risks in applications where a system
failure and/or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the person or entity
applying the equipment, and those so responsible are hereby requested to ensure that all
measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled out.
In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other
than under explicit contractual commitments, in no event shall ABB be responsible or liable for any
loss or damage resulting from the use of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility (EMC
Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage
limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB
in accordance with the product standard EN 60255-26 for the EMC directive, and with the product
standards EN 60255-1 and EN 60255-27 for the low voltage directive. The product is designed in
accordance with the international standards of the IEC 60255 series and ANSI C37.90.

Table of contents
Section 1 Introduction..............................................................................................................9
1.1 This manual................................................................................................................................................9
1.2 Intended audience....................................................................................................................................9
1.3 Product documentation........................................................................................................................ 10
1.3.1 Product documentation set.............................................................................................................10
1.3.2 Document revision history................................................................................................................11
1.3.3 Related documents.............................................................................................................................11
1.4 Document symbols and conventions..................................................................................................12
1.4.1 Symbols................................................................................................................................................ 12
1.4.2 Document conventions..................................................................................................................... 13
1.5 IEC61850 edition 1 / edition 2 mapping.............................................................................................13
Section 2 Safety information.................................................................................................21
2.1 Symbols on the product........................................................................................................................ 21
2.2 Warnings................................................................................................................................................... 21
2.3 Caution signs...........................................................................................................................................22
2.4 Note signs................................................................................................................................................ 23
Section 3 Available functions................................................................................................ 25
3.1 Wide area measurement functions..................................................................................................... 25
3.2 Back-up protection functions.............................................................................................................. 25
3.3 Control and monitoring functions...................................................................................................... 26
3.4 Communication...................................................................................................................................... 30
3.5 Basic IED functions.................................................................................................................................32
Section 4 Starting up..............................................................................................................35
4.1 Factory and site acceptance testing.................................................................................................. 35
4.2 Commissioning checklist......................................................................................................................35
4.3 Checking the power supply.................................................................................................................. 36
4.4 Energizing the IED.................................................................................................................................. 36
4.4.1 Checking the IED operation............................................................................................................. 36
4.4.2 IED start-up sequence.......................................................................................................................36
4.5 Setting up communication between PCM600 and the IED............................................................37
4.6 Writing an application configuration to the IED.............................................................................. 42
4.7 Checking CT circuits.............................................................................................................................. 42
4.8 Checking VT circuits...............................................................................................................................43
4.9 Using the RTXP test switch.................................................................................................................. 43
4.10 Checking the binary I/O circuits......................................................................................................... 44
4.10.1 Binary input circuits.......................................................................................................................... 44
Table of contents
1
Commissioning manual

4.10.2 Binary output circuits....................................................................................................................... 44
4.11 Checking optical connections..............................................................................................................44
Section 5 Configuring the IED and changing settings....................................................... 47
5.1 Overview...................................................................................................................................................47
5.2 Configuring analog CT inputs..............................................................................................................47
5.3 Reconfiguring the IED........................................................................................................................... 48
Section 6 Establishing connection and verifying the SPA/IEC communication.............49
6.1 Entering settings....................................................................................................................................49
6.1.1 Entering SPA settings....................................................................................................................... 49
6.1.2 Entering IEC settings........................................................................................................................ 49
6.2 Verifying the communication.............................................................................................................. 50
6.2.1 Verifying SPA communication.........................................................................................................50
6.2.2 Verifying IEC communication.......................................................................................................... 50
6.3 fiber optic loop....................................................................................................................................... 50
6.4 Optical budget calculation for serial communication with SPA/IEC .......................................... 51
Section 7 Establishing connection and verifying the LON communication.................... 53
7.1 Communication via the rear ports ..................................................................................................... 53
7.1.1 LON communication..........................................................................................................................53
7.1.2 The LON Protocol...............................................................................................................................54
7.1.3 Hardware and software modules................................................................................................... 54
7.2 Optical budget calculation for serial communication with LON ................................................. 55
Section 8 Establishing connection and verifying the IEC 61850 communication.......... 57
8.1 Overview................................................................................................................................................... 57
8.2 Setting the station communication....................................................................................................57
8.3 Verifying the communication...............................................................................................................58
Section 9 Establishing connection and verifying the IEEE C37.118/1344
communication...................................................................................................... 59
9.1 Overview...................................................................................................................................................59
9.2 Setting the PMU station communication (PMU Report)................................................................ 59
9.3 Setting the PMU station communication (PMU configuration)....................................................59
9.4 Setting the TCP/UDP client communication....................................................................................60
9.5 Verifying the communication.............................................................................................................. 64
9.5.1 Verifying the IEEE C37.118/1344 TCP communication............................................................... 64
9.5.2 Verifying the IEEE C37.118/1344 UDP communication...............................................................70
9.6 Optical budget calculation for RES670 - PDC communication...................................................... 71
Section 10 Testing IED operation............................................................................................73
10.1 Preparing for test................................................................................................................................... 73
10.1.1 Requirements...................................................................................................................................... 73
10.1.2 Preparing the IED to verify settings............................................................................................... 74
Table of contents
2
Commissioning manual

10.2 Activating the test mode...................................................................................................................... 75
10.3 Preparing the connection to the test equipment............................................................................ 75
10.4 Connecting the test equipment to the IED....................................................................................... 76
10.5 Releasing the function to be tested....................................................................................................77
10.6 Verifying analog primary and secondary measurement.................................................................78
10.7 Testing the protection functionality.................................................................................................. 79
10.8 Forcing of binary I/O signals for testing........................................................................................... 79
10.8.1 Forcing concept..................................................................................................................................79
10.8.2 How to enable forcing...................................................................................................................... 80
10.8.2.1 Enable forcing by using LHMI...................................................................................................... 80
10.8.2.2 Enable forcing using TESTMODE function block..................................................................... 80
10.8.3 How to change binary input/output signals using forcing...................................................... 80
10.8.3.1 Forcing by using LHMI....................................................................................................................81
10.8.3.2 Forcing by using PCM600............................................................................................................. 82
10.8.4 How to undo forcing changes and return the IED to normal operation.................................84
10.8.4.1 Undo forcing by using TestMode component..........................................................................84
10.8.4.2 Undo forcing by using LHMI.........................................................................................................84
10.8.4.3 Undo forcing by using PCM600...................................................................................................84
Section 11 Testing functionality by secondary injection.................................................... 87
11.1 Testing disturbance report.................................................................................................................. 87
11.1.1 Introduction........................................................................................................................................ 87
11.1.2 Disturbance report settings............................................................................................................ 87
11.1.3 Disturbance recorder (DR)................................................................................................................87
11.1.4 Event recorder (ER) and Event list (EL)..........................................................................................88
11.2 Identifying the function to test in the technical reference manual ............................................ 88
11.3 Differential protection.......................................................................................................................... 89
11.3.1 Line differential protection L3CPDIF and L6CPDIF (87L)...........................................................89
11.3.1.1 Verifying the settings.................................................................................................................... 89
11.3.1.2 Completing the test.......................................................................................................................90
11.4 Impedance protection........................................................................................................................... 91
11.4.1 Power swing detection ZMRPSB (68).............................................................................................91
11.4.1.1 Verifying the settings.................................................................................................................... 92
11.4.1.2 Testing the power swing detection function ZMRPSB (68)...................................................93
11.4.1.3 Testing the tR1 timer..................................................................................................................... 93
11.4.1.4 Testing the block input, interaction between FDPSPDIS (21) or FRPSPDIS (21) and
ZMRPSB (78).....................................................................................................................................93
11.4.1.5 Completing the test.......................................................................................................................94
11.4.2 Out-of-step protection OOSPPAM................................................................................................. 94
11.4.2.1 Verifying the settings.................................................................................................................... 94
11.4.2.2 Test of point RE (RFwdR, XFwdX).....................................................................................................99
11.4.2.3 Test of the boundary between zone 1 and zone 2, which is defined by the
parameter ReachZ1 .......................................................................................................................103
Table of contents
3
Commissioning manual

11.4.2.4 Test of the point SE (RRvsR, XRvsX).............................................................................................. 107
11.5 Current protection................................................................................................................................ 111
11.5.1 Four step phase overcurrent protection 3-phase output OC4PTOC (51_67)........................111
11.5.1.1 Verifying the settings................................................................................................................... 111
11.5.1.2 Completing the test...................................................................................................................... 112
11.5.2 Four step residual overcurrent protection, (Zero sequence or negative sequence
directionality) EF4PTOC (51N/67N).............................................................................................. 113
11.5.2.1 Four step directional ground fault protection........................................................................ 113
11.5.2.2 Four step non-directional ground fault protection................................................................113
11.5.2.3 Completing the test......................................................................................................................113
11.5.3 Four step negative sequence overcurrent protection NS4PTOC (46I2)................................114
11.5.3.1 Completing the test......................................................................................................................114
11.5.4 Sensitive directional residual overcurrent and power protection SDEPSDE (67N).............115
11.5.4.1 Measuring the trip and time limit for set values.....................................................................115
11.5.4.2 Completing the test......................................................................................................................119
11.5.5 Thermal overload protection, one time constant, Fahrenheit/Celsius LFPTTR/
LCPTTR (26)....................................................................................................................................... 120
11.5.5.1 Measuring the trip and time limit of set values......................................................................120
11.5.5.2 Completing the test..................................................................................................................... 120
11.5.6 Directional underpower protection GUPPDUP (37)................................................................... 121
11.5.6.1 Verifying the settings................................................................................................................... 121
11.5.6.2 Completing the test......................................................................................................................122
11.5.7 Directional overpower protection GOPPDOP (32)..................................................................... 122
11.5.7.1 Verifying the settings...................................................................................................................122
11.5.7.2 Completing the test......................................................................................................................123
11.6 Voltage protection................................................................................................................................123
11.6.1 Two step undervoltage protection UV2PTUV (27)..................................................................... 123
11.6.1.1 Verifying the settings...................................................................................................................123
11.6.1.2 Completing the test..................................................................................................................... 124
11.6.2 Two step overvoltage protection OV2PTOV (59).......................................................................125
11.6.2.1 Verifying the settings...................................................................................................................125
11.6.2.2 Extended testing...........................................................................................................................125
11.6.2.3 Completing the test..................................................................................................................... 125
11.7 Frequency protection...........................................................................................................................126
11.7.1 Underfrequency protection SAPTUF (81).................................................................................... 126
11.7.1.1 Verifying the settings...................................................................................................................126
11.7.1.2 Completing the test..................................................................................................................... 126
11.7.2 Overfrequency protection SAPTOF (81).......................................................................................127
11.7.2.1 Verifying the settings................................................................................................................... 127
11.7.2.2 Completing the test......................................................................................................................127
11.7.3 Rate-of-change frequency protection SAPFRC (81)...................................................................127
11.7.3.1 Verifying the settings................................................................................................................... 127
11.7.3.2 Completing the test..................................................................................................................... 128
Table of contents
4
Commissioning manual

11.7.4 Frequency time accumulation protection function FTAQFVR (81A)...................................... 128
11.7.4.1 Verifying the settings...................................................................................................................128
11.7.4.2 Completing the test..................................................................................................................... 130
11.8 Multipurpose protection.....................................................................................................................130
11.8.1 General current and voltage protection CVGAPC......................................................................130
11.8.1.1 Built-in overcurrent feature (non-directional)........................................................................ 130
11.8.1.2 Overcurrent feature with current restraint.............................................................................. 131
11.8.1.3 Overcurrent feature with voltage restraint..............................................................................131
11.8.1.4 Overcurrent feature with directionality....................................................................................131
11.8.1.5 Over/Undervoltage feature........................................................................................................ 132
11.8.1.6 Completing the test......................................................................................................................132
11.9 Secondary system supervision...........................................................................................................132
11.9.1 Current circuit supervision CCSSPVC (87)...................................................................................132
11.9.1.1 Verifying the settings...................................................................................................................133
11.9.1.2 Completing the test......................................................................................................................133
11.9.2 Fuse failure supervision FUFSPVC................................................................................................ 133
11.9.2.1 Checking that the binary inputs and outputs trip as expected ..........................................133
11.9.2.2 Measuring the trip value for the negative sequence function ............................................134
11.9.2.3 Measuring the trip value for the zero-sequence function ................................................... 135
11.9.2.4 Measuring the trip value for the dead line detection function............................................135
11.9.2.5 Checking the operation of the dv/dt and di/dt based function ........................................136
11.9.2.6 Completing the test..................................................................................................................... 136
11.10 Control.................................................................................................................................................... 136
11.10.1 Single command, 16 signals SINGLECMD....................................................................................136
11.11 Logic........................................................................................................................................................ 137
11.11.1 Tripping logic, common 3-phase output SMPPTRC (94)..........................................................137
11.11.1.1 Three-phase operating mode..................................................................................................... 137
11.11.1.2 1ph/3ph operating mode............................................................................................................ 137
11.11.1.3 1ph/2ph/3ph operating mode................................................................................................... 138
11.11.1.4 Circuit breaker lockout................................................................................................................ 139
11.11.1.5 Completing the test..................................................................................................................... 139
11.12 Monitoring..............................................................................................................................................139
11.12.1 Gas medium supervision SSIMG....................................................................................................139
11.12.1.1 Testing the liquid medium supervision for alarm and lock out conditions...................... 139
11.12.1.2 Completing the test..................................................................................................................... 140
11.12.2 Liquid medium supervision SSIML............................................................................................... 140
11.12.2.1 Testing the liquid medium supervision for alarm and lock out conditions......................140
11.12.2.2 Completing the test..................................................................................................................... 140
11.12.3 Breaker monitoring SSCBR............................................................................................................ 140
11.12.3.1 Verifying the settings...................................................................................................................141
11.12.3.2 Completing the test..................................................................................................................... 142
11.12.4 Event function EVENT......................................................................................................................142
11.12.5 Limit counter L4UFCNT.................................................................................................................. 143
Table of contents
5
Commissioning manual

11.12.5.1 Completing the test..................................................................................................................... 143
11.13 Metering................................................................................................................................................. 143
11.13.1 Pulse-counter logic PCFCNT.......................................................................................................... 143
11.13.2 Function for energy calculation and demand handling ETPMMTR........................................ 143
11.13.2.1 Verifying the settings...................................................................................................................143
11.13.2.2 Completing the test..................................................................................................................... 144
11.14 Station communication.......................................................................................................................144
11.14.1 Multiple command and transmit MULTICMDRCV / MULTICMDSND..................................... 144
11.15 Remote communication......................................................................................................................145
11.15.1 Binary signal transfer BinSignReceive, BinSignTransm............................................................145
11.16 Basic IED functions.............................................................................................................................. 146
11.16.1 Parameter setting group handling SETGRPS............................................................................. 146
11.16.1.1 Verifying the settings.................................................................................................................. 146
11.16.1.2 Completing the test..................................................................................................................... 147
11.17 Exit test mode....................................................................................................................................... 147
Section 12 Commissioning and maintenance of the fault clearing system....................149
12.1 Commissioning tests...........................................................................................................................149
12.2 Periodic maintenance tests................................................................................................................149
12.2.1 Visual inspection.............................................................................................................................. 150
12.2.2 Maintenance tests........................................................................................................................... 150
12.2.2.1 Preparation.................................................................................................................................... 150
12.2.2.2 Recording........................................................................................................................................ 151
12.2.2.3 Secondary injection.......................................................................................................................151
12.2.2.4 Alarm test........................................................................................................................................151
12.2.2.5 Self supervision check.................................................................................................................. 151
12.2.2.6 Trip circuit check........................................................................................................................... 151
12.2.2.7 Measurement of service currents.............................................................................................. 152
12.2.2.8 Restoring........................................................................................................................................ 152
Section 13 Troubleshooting...................................................................................................153
13.1 Checking the self supervision signals.............................................................................................. 153
13.1.1 Checking the self supervision function........................................................................................153
13.1.1.1 Determine the cause of an internal failure...............................................................................153
13.1.2 Self supervision HMI data............................................................................................................... 153
13.1.2.1 General IED status.........................................................................................................................153
13.1.2.2 Communication Diagnostics......................................................................................................154
13.2 Fault tracing...........................................................................................................................................159
13.2.1 Internal fault indications.................................................................................................................159
13.2.2 Using front-connected PC.............................................................................................................. 161
13.2.3 Diagnosing the IED status via the LHMI hint menu...................................................................162
13.2.4 Hardware re-configuration............................................................................................................ 163
13.3 Repair instruction.................................................................................................................................164
Table of contents
6
Commissioning manual

13.4 Repair support...................................................................................................................................... 165
13.5 Maintenance.......................................................................................................................................... 165
Section 14 Glossary.................................................................................................................167
Table of contents
7
Commissioning manual

8

Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v19
The commissioning manual contains instructions on how to commission the IED. The manual can
also be used by system engineers and maintenance personnel for assistance during the testing
phase. The manual provides procedures for the checking of external circuitry and energizing the
IED, parameter setting and configuration as well as verifying settings by secondary injection. The
manual describes the process of testing an IED in a substation which is not in service. The
chapters are organized in the chronological order in which the IED should be commissioned. The
relevant procedures may be followed also during the service and maintenance activities.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v10
This manual addresses the personnel responsible for commissioning, maintenance and taking the
IED in and out of normal service.
The commissioning personnel must have a basic knowledge of handling electronic equipment. The
commissioning and maintenance personnel must be well experienced in using protection
equipment, test equipment, protection functions and the configured functional logics in the IED.
1MRK 511 366-UUS A Section 1
Introduction
9
Commissioning manual

1.3 Product documentation
1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15
IEC07000220-4-en.vsd
Planning & purchase Engineering Installing Commissioning Operation Maintenance Decommissioning Deinstalling & disposal
Application manual
Operation manual
Installation manual
Engineering manual
Communication
protocol manual
Cyber security
deployment guideline
Technical manual
Commissioning manual
IEC07000220 V4 EN-US
Figure 1: The intended use of manuals throughout the product lifecycle
The engineering manual contains instructions on how to engineer the IEDs using the various tools
available within the PCM600 software. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also recommends a sequence
for the engineering of protection and control functions, LHMI functions as well as communication
engineering for IEC 60870-5-103, IEC 61850, DNP3, LON and SPA.
The installation manual contains instructions on how to install the IED. The manual provides
procedures for mechanical and electrical installation. The chapters are organized in the
chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The manual can
also be used by system engineers and maintenance personnel for assistance during the testing
phase. The manual provides procedures for the checking of external circuitry and energizing the
IED, parameter setting and configuration as well as verifying settings by secondary injection. The
manual describes the process of testing an IED in a substation which is not in service. The
chapters are organized in the chronological order in which the IED should be commissioned. The
relevant procedures may be followed also during the service and maintenance activities.
Section 1 1MRK 511 366-UUS A
Introduction
10
Commissioning manual

The operation manual contains instructions on how to operate the IED once it has been
commissioned. The manual provides instructions for the monitoring, controlling and setting of the
IED. The manual also describes how to identify disturbances and how to view calculated and
measured power grid data to determine the cause of a fault.
The application manual contains application descriptions and setting guidelines sorted per
function. The manual can be used to find out when and for what purpose a typical protection
function can be used. The manual can also provide assistance for calculating settings.
The technical manual contains operation principle descriptions, and lists function blocks, logic
diagrams, input and output signals, setting parameters and technical data, sorted per function.
The manual can be used as a technical reference during the engineering phase, installation and
commissioning phase, and during normal service.
The communication protocol manual describes the communication protocols supported by the
IED. The manual concentrates on the vendor-specific implementations.
The point list manual describes the outlook and properties of the data points specific to the IED.
The manual should be used in conjunction with the corresponding communication protocol
manual.
The cyber security deployment guideline describes the process for handling cyber security when
communicating with the IED. Certification, Authorization with role based access control, and
product engineering for cyber security related events are described and sorted by function. The
guideline can be used as a technical reference during the engineering phase, installation and
commissioning phase, and during normal service.
1.3.2 Document revision history GUID-C8027F8A-D3CB-41C1-B078-F9E59BB73A6C v2.1.1
Document revision/date History
January 2016 First Release
March 2019 Maintenance Release
1.3.3 Related documents GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v4
Documents related to RES670 Document numbers
Application manual 1MRK 511 364-UUS
Commissioning manual 1MRK 511 366-UUS
Product guide 1MRK 511 367-BEN
Technical manual 1MRK 511 365-UUS
Type test certificate 1MRK 511 367-TUS
670 series manuals Document numbers
Operation manual 1MRK 500 123-UUS
Engineering manual 1MRK 511 355-UUS
Installation manual 1MRK 514 024-UUS
Communication protocol manual, DNP3 1MRK 511 348-UUS
Table continues on next page
1MRK 511 366-UUS A Section 1
Introduction
11
Commissioning manual

670 series manuals Document numbers
Communication protocol manual, IEC 61850 Edition 2 1MRK 511 350-UEN
Point list manual, DNP3 1MRK 511 354-UUS
Accessories guide 1MRK 514 012-BUS
Connection and Installation components 1MRK 513 003-BEN
Test system, COMBITEST 1MRK 512 001-BEN
1.4 Document symbols and conventions
1.4.1 Symbols GUID-2945B229-DAB0-4F15-8A0E-B9CF0C2C7B15 v12
The electrical warning icon indicates the presence of a hazard which could result in
electrical shock.
The warning icon indicates the presence of a hazard which could result in personal
injury.
The caution hot surface icon indicates important information or warning about the
temperature of product surfaces.
Class 1 Laser product. Take adequate measures to protect the eyes and do not view
directly with optical instruments.
The caution icon indicates important information or warning related to the
concept discussed in the text. It might indicate the presence of a hazard which
could result in corruption of software or damage to equipment or property.
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project or how to
use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand that under
certain operational conditions, operation of damaged equipment may result in degraded process
Section 1 1MRK 511 366-UUS A
Introduction
12
Commissioning manual

performance leading to personal injury or death. It is important that the user fully complies with all
warning and cautionary notices.
1.4.2 Document conventions GUID-96DFAB1A-98FE-4B26-8E90-F7CEB14B1AB6 v8
• Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary also
contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the push button
icons.
For example, to navigate between the options, use and .
• HMI menu paths are presented in bold.
For example, select Main menu/Settings.
• LHMI messages are shown in Courier font.
For example, to save the changes in non-volatile memory, select Yes and press .
• Parameter names are shown in italics.
For example, the function can be enabled and disabled with the
Operation setting.
• Each function block symbol shows the available input/output signal.
• the character ^ in front of an input/output signal name indicates that the signal name
may be customized using the PCM600 software.
• the character * after an input signal name indicates that the signal must be connected
to another function block in the application configuration to achieve a valid application
configuration.
• Dimensions are provided both in inches and millimeters. If it is not specifically mentioned
then the dimension is in millimeters.
1.5 IEC61850 edition 1 / edition 2 mapping
GUID-C5133366-7260-4C47-A975-7DBAB3A33A96 v2
Table 1: IEC61850 edition 1 / edition 2 mapping
Function block name Edition 1 logical nodes Edition 2 logical nodes
AEGPVOC AEGGAPC AEGPVOC
AGSAL AGSAL
SECLLN0
AGSAL
ALMCALH ALMCALH ALMCALH
ALTIM ALTIM
ALTMS ALTMS
ALTRK ALTRK
BCZSPDIF BCZSPDIF BCZSPDIF
BCZTPDIF BCZTPDIF BCZTPDIF
BDCGAPC SWSGGIO BBCSWI
BDCGAPC
BRCPTOC BRCPTOC BRCPTOC
BRPTOC BRPTOC BRPTOC
BTIGAPC B16IFCVI BTIGAPC
BUSPTRC_B1 BUSPTRC
BBSPLLN0
BUSPTRC
Table continues on next page
1MRK 511 366-UUS A Section 1
Introduction
13
Commissioning manual

Function block name Edition 1 logical nodes Edition 2 logical nodes
BUSPTRC_B2 BUSPTRC BUSPTRC
BUSPTRC_B3 BUSPTRC BUSPTRC
BUSPTRC_B4 BUSPTRC BUSPTRC
BUSPTRC_B5 BUSPTRC BUSPTRC
BUSPTRC_B6 BUSPTRC BUSPTRC
BUSPTRC_B7 BUSPTRC BUSPTRC
BUSPTRC_B8 BUSPTRC BUSPTRC
BUSPTRC_B9 BUSPTRC BUSPTRC
BUSPTRC_B10 BUSPTRC BUSPTRC
BUSPTRC_B11 BUSPTRC BUSPTRC
BUSPTRC_B12 BUSPTRC BUSPTRC
BUSPTRC_B13 BUSPTRC BUSPTRC
BUSPTRC_B14 BUSPTRC BUSPTRC
BUSPTRC_B15 BUSPTRC BUSPTRC
BUSPTRC_B16 BUSPTRC BUSPTRC
BUSPTRC_B17 BUSPTRC BUSPTRC
BUSPTRC_B18 BUSPTRC BUSPTRC
BUSPTRC_B19 BUSPTRC BUSPTRC
BUSPTRC_B20 BUSPTRC BUSPTRC
BUSPTRC_B21 BUSPTRC BUSPTRC
BUSPTRC_B22 BUSPTRC BUSPTRC
BUSPTRC_B23 BUSPTRC BUSPTRC
BUSPTRC_B24 BUSPTRC BUSPTRC
BUTPTRC_B1 BUTPTRC
BBTPLLN0
BUTPTRC
BUTPTRC_B2 BUTPTRC BUTPTRC
BUTPTRC_B3 BUTPTRC BUTPTRC
BUTPTRC_B4 BUTPTRC BUTPTRC
BUTPTRC_B5 BUTPTRC BUTPTRC
BUTPTRC_B6 BUTPTRC BUTPTRC
BUTPTRC_B7 BUTPTRC BUTPTRC
BUTPTRC_B8 BUTPTRC BUTPTRC
BZISGGIO BZISGGIO BZISGAPC
BZITGGIO BZITGGIO BZITGAPC
BZNSPDIF_A BZNSPDIF BZASGAPC
BZASPDIF
BZNSGAPC
BZNSPDIF
BZNSPDIF_B BZNSPDIF BZBSGAPC
BZBSPDIF
BZNSGAPC
BZNSPDIF
Table continues on next page
Section 1 1MRK 511 366-UUS A
Introduction
14
Commissioning manual