ABB LME620-AI User manual

—
ABB MEASUREMENT & ANALYTICS | OPERATING INSTRUCTION
LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861
Electronic unit for field installation (Contrac)
—
ABB Limited
Measurement & Analytics
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: [phone]
Fax: [phone]
Email: [e-mail]
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
abb.com/actuators
ABB Inc.
Measurement & Analytics
125 E. County Line Road
Warminster, PA 18974
USA
Tel: [phone]
Fax: [phone]
For the control of Contrac control
actuators series PME, LME, RHD
and RSD
OI/PME/LME/EAN823/EBN853/EBN861-EN Rev. E 10.2018
—
Integrated
LME620-AI
PME120-AI
Field-mount
EAN823
EBN853
EBN861
Introduction
The electronic unit builds the interface between
the actuator and the control system.
During continuous positioning, the electronic unit
varies the motor torque continuously until the
actuator force and the control valve force are
balanced.
High response sensitivity and high positioning
accuracy with short positioning time ensure an
excellent control quality and a long actuator life.
Additional Information
Additional documentation on LME620-AI / PME120-AI
/ EAN823 / EBN853 / EBN861 is available for
download free of charge at www.abb.com/actuators.
Alternatively simply scan this code:
—
We reserve the right to make technical changes or modify the contents of this document
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole
or in parts – is forbidden without prior written consent of ABB.
Copyright© 2018 ABB
All rights reserved 3KXE181008R4201

2 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
Table of contents
Change from one to two columns
1Safety.......................................................................... 3
General information and instructions.................................. 3
Warnings.................................................................................... 3
Intended use .............................................................................4
Improper use.............................................................................4
Notes on data safety ...............................................................4
Warranty provisions.................................................................4
Manufacturer’s address..........................................................4
2Design and function .................................................. 5
Design ........................................................................................5
LME620-AI / PME120-AI (with integrated EAI823
electronic unit).....................................................................5
EAN823 / EBN853 ................................................................5
EBN861 ..................................................................................6
Principle of operation..............................................................6
Overview .................................................................................... 7
Device designs..........................................................................8
3Product identification ............................................10
Name plates ............................................................................10
Scope of delivery ....................................................................10
Delivery status ........................................................................ 11
4Transport and storage............................................ 12
Inspection................................................................................ 12
Transporting the device........................................................ 12
Safety instructions............................................................ 12
Returning devices................................................................... 12
Storing the device .................................................................. 12
5Installation ............................................................... 12
Safety instructions................................................................. 12
Mounting ................................................................................. 12
LME620-AI / PME120-AI (with integrated EAI823
electronic unit)................................................................... 13
EAN823 / EBN853 .............................................................. 13
EBN861 ................................................................................ 13
Dimensions.............................................................................. 14
Electronic unit EAN823 (Contrac)...................................14
Electronic unit EBN853 (Contrac)................................... 15
Electronic unit EBN861 (Contrac)...................................16
6Electrical connections............................................. 17
Safety instructions................................................................. 17
Instructions on the use of Error Current Circuit Breakers
(RCDs)....................................................................................... 17
General ................................................................................ 17
Conductor cross-section on universal plug....................... 17
Conductor cross-section on electronic unit...................... 18
Cable glands............................................................................ 18
Selection of suited connection cables ...............................18
Integrated electronic unit for PME120-AI / LME620-AI...19
Electronic unit EAN823 (Contrac) / EBN853 (Contrac) /
EBN861 (Contrac)................................................................... 21
Connection examples............................................................23
Electrical data for inputs and outputs............................... 25
Connection on the device..................................................... 28
Connection of the power and signal cable on the
actuator................................................................................... 29
7Commissioning and operation.............................. 30
General information ..............................................................30
Engineering Software ECOM688 and ECOM700.........30
Checks prior to commissioning .......................................... 30
Before powering up the power supply.......................... 30
After powering up the power supply ............................30
Commissioning and service field.........................................31
Meaning of the LED indicators....................................... 32
Hardware settings................................................................. 33
Basic Setup ............................................................................. 33
Manual (MAN)- and Automatic Operation (AUT) ............. 34
8Diagnosis / error messages ...................................35
Definition – Alarms and Errors ............................................ 35
Alarm Diagram ....................................................................... 35
Error Diagram......................................................................... 36
Hardware Errors..................................................................... 37
9Maintenance ............................................................ 38
Electronic unit ........................................................................ 38
Control actuator .................................................................... 38
10Repair ....................................................................... 38
Returning devices .................................................................. 38
Fuses........................................................................................ 39
11Recycling and disposal........................................... 40
Notice on RoHS II-Directive 2011/65/EU...........................40
12Approvals and certifications ................................. 40
13Additional documents............................................ 40
14Appendix ...................................................................41
Return form............................................................................. 41

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 3
Change from one to two columns
1Safety
hange from one to two columns
General information and instructions
These instructions are an important part of the product and
must be retained for future reference.
Installation, commissioning, and maintenance of the product
may only be performed by trained specialist personnel who have
been authorized by the plant operator accordingly. The specialist
personnel must have read and understood the manual and must
comply with its instructions.
For additional information or if specific problems occur that are
not discussed in these instructions, contact the manufacturer.
The content of these instructions is neither part of nor an
amendment to any previous or existing agreement, promise or
legal relationship.
Modifications and repairs to the product may only be performed
if expressly permitted by these instructions.
Information and symbols on the product must be observed.
These may not be removed and must be fully legible at all times.
The operating company must strictly observe the applicable
national regulations relating to the installation, function testing,
repair and maintenance of electrical products.
Warnings
The warnings in these instructions are structured as follows:
DANGER
The signal word ‘DANGER’ indicates an imminent danger.
Failure to observe this information will result in death or
severe injury.
WARNING
The signal word ‘WARNING’ indicates an imminent danger.
Failure to observe this information may result in death or
severe injury.
CAUTION
The signal word ‘CAUTION’ indicates an imminent danger.
Failure to observe this information may result in minor or
moderate injury.
NOTICE
The signal word
‘
NOTIC
E
’
indicates possible material damage.
Note
‘Note’ indicates useful or important information about the
product.

4 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 1 Safety
Intended use
The electronic units of type LME620-AI / PME120-AI / EAN823 /
EBN853 / EBN861 interconnected as illustrated in this operating
instruction are used exclusively to control the PME120, LME620,
RHD... and RSD... series control actuators.
Using these actuators for any other purpose will introduce a risk
of personal injury and can also damage or impair the device's
operational reliability.
Improper use
The following are considered to be instances of improper use of
the device:
• For use as a climbing aid, for example for mounting
purposes.
• For use as a bracket for external loads, for example as a
support for piping, etc.
• Material application, for example by painting over the
housing, name plate or welding/soldering on parts.
• Material removal, for example by spot drilling the
housing.
Notes on data safety
This product is designed to be connected to and to
communicate information and data via a network interface.
It is operator’s sole responsibility to provide and continuously
ensure a secure connection between the product and your
network or any other network (as the case may be).
Operator shall establish and maintain any appropriate measures
(such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data,
installation of anti-virus programs, etc.) to protect the product,
the network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and / or theft of data or information.
ABB Automation Products GmbH and its affiliates are not liable
for damages and / or losses related to such security breaches,
any unauthorized access, interference, intrusion, leakage and /
or theft of data or information.
Warranty provisions
Using the device in a manner that does not fall within the scope
of its intended use, disregarding this manual, using
underqualified personnel, or making unauthorized alterations
releases the manufacturer from liability for any resulting
damage. This renders the manufacturer's warranty null and void.
Manufacturer’s address
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
Customer service center
Tel: [phone]
Email: [email protected]
Change from one to two columns

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 5
2Design and function
Design
The actuators with integrated electronic unit (PME120-AI and
LME620-AI) consist of two components. One component is the
gearing which includes the connection components and the
transformer. The other component is made up of the electronic
unit (EAI823) and the commissioning and service field (ISF) for
‘local operation’ and actuator setup.
The electronic units EAN823, EBN853 and EBN861 consist of two
housing halves, one holding the connection components and the
transformer, the other holding the electronics and the
commissioning and service field (ISF) for ‘local operation’ of the
actuator.
LME620-AI / PME120-AI (with integrated EAI823
electronic unit)
1Cover for commissioning and
service field
2Electronic unit cover
3Universal plug
(power supply, signal cable)
Figure 1: LME620-AI with integrated electronic unit (example)
EAN823 / EBN853
1Connection housing
2Electronic unit cover
3Cover for commissioning and
service field
4Cover for terminal
compartment
5Cable gland
6Tap holes for cable glands
7Analog input fuse
8Terminals (signals)
9Anti-dewing heater fuse
0Terminals (motor cable)
kPower supply fuse
lTerminals (power supply)
Figure 2: Presentation terminal compartment

6 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 2 Design and function
… Design
EBN861
1Electronic unit cover
2Lifting eye
3Commissioning and service field
4Cover screws
5Cover hinges
6Tap holes for cable glands
7Ground terminal
8Terminals (power supply)
9Terminals (motor cable)
0Binary output fuses
kTerminals (signals)
lLower part of electronic unit
Figure 3: Presentation without cover for terminal compartment
The electronic unit is made up of two housing halves (electronic
cover / electronic unit lower part) which can be separated for
easier assembly.
Principle of operation
The electronic unit builds the interface between the actuator and
the control system.
During continuous positioning, the electronic unit varies the
motor torque continuously until the actuator force and the
control valve force are balanced. High response sensitivity and
high positioning accuracy with short positioning time ensure an
excellent control quality and a long actuator life.
Electronic units are available for assembly in the field near the
actuator, remotely in a mounting rack or for integrated assembly
(smallest actuator type). In addition to the terminals, the
electronic unit contains the microprocessor, frequency converter
for motor control, analog and binary inputs and outputs,
PROFIBUS® or HART® communication interfaces, the
commissioning and service field and a plug connection to
connect a PC.
No matter what the motor power of the respective actuator is,
all electronic units are supplied single-phase by 230 V or 115 V
mains supply (50 Hz or 60 Hz).
The commissioning and service field enables the end positions
and direction of rotation to be set on the actuator. Moreover,
status information is displayed using LEDs. Push buttons can be
used to operate the actuator and set the operating mode
(Automatic, Out of Service).
Change from tw o to one column

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 7
Overview
Figure 4: Structure of the Contrac components (example)

8 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 2 Design and function
Device designs
EAN823
IP rating IP 66 in accordance with IEC 60529 / EN 60529
NEMA 4X in accordance with CAN / CSA22.2 No. 94
Humidity ≤95% annual average; condensation not permitted
Ambient temperature −25 to 55 °C (−13 to 131 °F)
Transport and storage temperature −25 to 70 °C (−13 to 158 °F)
Long-term storage temperature −25 to 40 °C (−13 to 104 °F)
Mounting position On vertical mounting plate, lateral cable gland, left
Vibration stress Maximum 150 Hz: acceleration: 1 g (in accordance with EN 60068-2-6, Table C.2)
Electrical connection Mains supply and connection cable to the control system through screw terminals.
Connection cable between electronic unit and actuator tightly fastened optionally to the electronic unit,
from the actuator side using a connector to the connection to the actuator. Available cable lengths 5 m
(16 ft), 10 m (32 ft) or 20 m (65 ft).
Maximum cable length for delivery without cable: 30 m (98 ft)
Weight 11 kg (24 lbs)
EBN853
IP rating IP 66 in accordance with IEC 60529 / EN 60529
NEMA 4X in accordance with CAN / CSA22.2 No. 94
Humidity ≤95% annual average; condensation not permitted
Ambient temperature −25 to 55 °C (−13 to 131 °F)
Transport and storage temperature −25 to 70 °C (−13 to 158 °F)
Long-term storage temperature −25 to 40 °C (−13 to 104 °F)
Mounting position On vertical mounting plate, lateral cable gland, left
Vibration stress Maximum 150 Hz: acceleration: 1 g (in accordance with EN 60068-2-6, Table C.2)
Paint 2-layer component epoxy (RAL 9005, black)
Electrical connection Mains supply via screw terminals; all other connections made via screw-type plug connectors
Connection cable between electronic unit and actuator tightly fastened to the electronic unit, from the
actuator side using a connector to the connection to the actuator. Maximum cable length 100 m (328 ft).
In actuators in explosion-proof design, the connection cable is tightly fastened to the actuator without a
connector through the screw terminals.
Optional, loose cable set supplied acc. to length requirements
Weight 11 kg (24 lbs)

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 9
EBN861
IP rating IP 66
Humidity ≤95% annual average; condensation not permitted
Ambient temperature -25 to 55 °C (-13 to 131 °F)
Transport and storage temperature -25 to 70 °C (-13 to 158 °F)
Long-term storage temperature -25 to 40 °C (-13 to 104 °F)
Mounting position On vertical mounting plate, cable gland at the bottom
Vibration stress Maximum 150 Hz: acceleration: 1 g (in accordance with EN 60068-2-6, Table C.2)
Paint 2-layer component epoxy (RAL 9005, black)
Electrical connection Mains supply via screw terminals; all other connections made via screw-type plug connectors
Connection cable between electronic unit and actuator tightly fastened to the electronic unit, from the
actuator side using a connector to the connection to the actuator. Maximum cable length 100 m (328 ft).
In actuators in explosion-proof design, the connection cable is tightly fastened to the actuator without a
connector through the screw terminals.
Optional, loose cable set supplied acc. to length requirements
Weight 40 kg (88 lbs)
Change from one to two columns

10 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
3Product identification
Name plates
M10441
Elektronik / Electronics Type: ...
Made in Germany
B-Nr./No. .... .. NL
U = 23 0 V .. . Jahr/Year
f = 5 0/60 Hz ± 5 % P= max.... .. W
t = . ... ... ... .... ....°C IP 20 CE
Ext. Sicherung / Fuse ... ....
D-32425 Mind
en
ABB Automation Products GmbH
Schillerstrasse 72
1
2
3
4
5
6
7
l
k
j
9
8
1Full type designation
2 Manufacturing number
3 Power supply
4 Permissible mains frequency
5 Ambient temperature range
6 Specifications for external fuse
protection
7 Manufacturer address
8 CE mark
9 IP rating
0 Maximum power consumption
k Year of manufacture
l NL no. (for no-list design)
Figure 5: Hardware name plate (example)
M10361
Für / For
Antrieb /Actuator
Nennwerte /Rated Values
M=
F-Nr. / No.
Software Version
NL.
°/s=
1
2
3
4
5
6
1Associated Contrac control
actuator
2 Nominal torque or rated
actuator strength / set speed
3 Manufacturing number
4 NL no. (for no-list design)
5 Installed software version
6 Free for customer-specific
information
Figure 6: Software name plate (example)
Note
In electronic units which can be separated for assembly, the
name plate for the hardware is located on the lower part of the
electronic unit (Figure 1). The name plate for the software
(Figure 2) and an additional name plate for the hardware (Figure
3) are located on the electronic unit cover.
The lower part of the electronic unit and the electronic cover are
independent assemblies, therefore the respective
manufacturing numbers can differ.
M10443
Elektronik / Electronics Type: ...
Made in Germany
B-Nr./No. .... .. NL
Jahr/Year
t = . ... ... ....... ....°C IP 20 CE
D-32425 Mind
en
ABB Automation Products GmbH
Schillerstrasse 72
1
2
3
4
8
7
6
5
1Full type designation
2 Manufacturing number
3 Ambient temperature range
4 Manufacturer address
5 CE mark
6 IP rating
7 Year of manufacture
8 NL no. (for no-list design)
Figure 7: Additional name plate for hardware (example)
Scope of delivery
• Metric tap holes for cable entries with IP 66 sealing plugs.

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 11
Delivery status
The individual actuator configuration may vary from the
standard setup above. This information can be displayed via the
user interface.
Unless otherwise specified by the user, the electronic units are
delivered with the following standard configuration:
Conventional communication
Parameter Setting
Function selection Positioner, parameter: set point
Set point function Analog set point
Set point range 4 to 20 mA
Set point characteristic Linear; set point = position value
Actual value range 4 to 20 mA
Nominal torque / rated force in
±direction
100 %
Automatic speed in ±direction: 100 %
Action in 0 % / 100 % end
position
Keep leak-tight with nominal torque / rated
force
Digital inputs Digital input 1 Manual / Automatic
switching,
Digital input 2 / 3 Travel command ±
Digital outputs Digital output 1 ready for operation / error
message,
Digital output 2 / 3 end position signaling
0 % / 100 %
Brake Away Function Deactivated
Shut-off function Deactivated
Positioning loop monitoring Deactivated
Set point monitoring Deactivated
Alarm Type Deactivated
Action after restoration of
power
Switch to Automatic
Working range of actuator Not set
PROFIBUS DP® communication
Parameter Setting
Function selection Positioner, parameter: set point
Set point function Digital
Set point range 4 to 20 mA
Set point characteristic Linear; set point = position value
Actual value range Digital
Nominal torque / rated force in
±direction
100 %
Automatic speed in ±direction: 100 %
Action in 0 % / 100 % end
position
Keep leak-tight with nominal torque / rated
force
Digital outputs Digital output 1 / 2 end position signal 0
% / 100 %
Brake Away Function Deactivated
Shut-off function Deactivated
Positioning loop monitoring Deactivated
Communication monitoring PROFIBUS DP® / V0:
Activated
Lock in last position
PROFIBUS DP® / V1:
Activated
After delay time has elapsed (standard
configuration 5 s)
Lock in last position
Alarm Type Deactivated
Action after restoration of
power
Switch to Automatic
Working range of actuator Not set

12 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
4Transport and storage
Inspection
Check the devices immediately after unpacking for possible
damage that may have occurred from improper transport.
Details of any damage that has occurred in transit must be
recorded on the transport documents.
All claims for damages must be submitted to the shipper
without delay and before installation.
Transporting the device
Safety instructions
DANGER
Danger to life due to falling or toppling loads.
Risk of death or serious injury due to the device falling down
or toppling over!
• Standing under suspended loads is prohibited.
• Do not detach the hoisting equipment until installation is
complete.
• Only use the dedicated load pick-up devices (eyebolts) for
suspending the components.
Consider the following items during transport:
• Pay attention to the device weight details.
• Do not expose the device to humidity during transport.
Pack the device accordingly.
• Pay attention to the permissible transportation
temperatures for the device.
Returning devices
For the return of devices, follow the instructions in Returning
devices on page 38.
Storing the device
The electronic units LME620-AI / PME120-AI / EAN823 / EBN853
/ EBN861 comply with IP rating IP 20. The electronic units should
be stored in accordance with this IP rating. Condensation is not
permitted.
The permissible storage temperatures as well as the ambient
conditions (humidity) should be complied with (see Device
designs on page 8).
For longer storage periods, we recommend packing the units in
foil with a dessicant added.
The dessicant must be checked for regularly for effectivity.
5Installation
Safety instructions
DANGER
Danger to life due to falling or toppling loads.
Risk of death or serious injury due to the device falling down
or toppling over!
• Standing under suspended loads is prohibited.
• Do not detach the hoisting equipment until installation is
complete.
• Only use the dedicated load pick-up devices (eyebolts) for
suspending the components.
Please observe the following safety instructions
• Only qualified specialists may mount and adjust the control
actuator, and make the electrical connection.
• When working on the actuator or the electronics always
observe the locally valid accident prevention regulations and
the regulations concerning the construction of technical
installations.
• Switch off the supply voltage and take precautions to
prevent unintentional switch-on.
Mounting
NOTICE
Damage to components!
Damage to components caused by ingress of foreign bodies
or humidity.
• Keep all housing covers and terminal compartments
closed during installation to prevent the ingress of foreign
bodies such as drilling shavings, liquids or dust.
When installing the electronic unit, observe the following points:
• You must be able to activate the power supply of the
electronic unit on-site.
• All signal cables and the motor cable between the
actuator and electronic unit must be shielded.
• The cable shield must be placed on both housings when
connecting the electronic unit and the actuator.
• The maximum vibration load must be observed during
installation, see Device designs on page 8.
• When mounting the electronic unit in work and traffic
areas that may be accessed by unauthorized persons, the
operator is required to take suited protective measures.

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 13
LME620-AI / PME120-AI (with integrated EAI823
electronic unit)
Refer to the operating instruction of the linear actuator or rotary
actuator for detailed information on the assembly of actuators
with integrated electronics.
EAN823 / EBN853
1.Fasten the electronic unit to a vertical mounting plate using
grade 8.8 screws. Tensile strength 800 N/mm2
(116032 pounds/square in.), yield strength 640 N/mm2
(92826 pounds/square in.).
2.Provide adequate room for installation and ensure easy
access.
3.The cable entries must be directed to the left.
EBN861
Note
The total weight of the electronic unit is 40 kg (88 lbs). For this
reason, the electronic unit is equipped with a load-bearing
eyelet.
If, for technical reasons, the load-bearing eyelet cannot be used,
the two halves of the housing can be installed separately.
Separating the housing halves
1.Place the electronic unit on a horizontal surface.
2.Unscrew the cover screws(Figure 3 on page 6).
3.Flip open the electronic unit cover.
4.Disconnect the internal plug connection between the housing
halves.
5.Close the electronic unit cover.
6.Unscrew the hinge screw (Figure 3 on page 6).
7.Flip the electronic unit cover forward while lifting it up and
off the hinge pin. Precisely guide the cover of the electronic
unit cover in the process.
Mounting
1.Fasten the electronic unit or the lower part of the electronic
unit to the vertical mounting rail of the mounting rack using
grade 8.8 screws. Tensile strength 800 N/mm2
(116032 pounds/square in.), yield strength 640 N/mm2
(92826 pounds/square in.).
2.Provide adequate room for installation and ensure easy
access.
3.The cable entries must be directed down.
Mounting the housing halves
1.Set the electronic unit cover down on the hinge pin and screw
in the hinge screw. Precisely guide the cover of the electronic
unit cover in the process.
2.Reconnect the internal plug connection.
3.Close the electronic unit cover and screw in the cover screws
(Figure 3 on page 6).
Change from tw o to one column

14 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 5 Installation
Dimensions
Electronic unit EAN823 (Contrac)
M10180
303 (11.93)
252,5 (9.94)
278 (10.94)
30 (1.18)
150 (5.91)
122 (4.8)
Ø9 (0.35)
100 (3.94) 15 (0.59)
250 (9.84)
230 (9.06)
1bcde
M20 x 1,5
M20 x 1,5
M20 x 1,5
M20 x 1,5
M25 x 1,5
1Back view
2 Leave at least 100 mm (3.94 in) distance for the cable gland and cable
radius
3 Side view
4 Front view
5 Space for disassembly
Figure 8: Dimensions in mm (in)

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 15
Electronic unit EBN853 (Contrac)
M10186
122 (4.8) 297 (11.69) 260 (10.24)
15 (0.59)
100 (3.94)
230 (9.06)
250 (9.84)
Ø9 (0.35)
252,5 (9.94)
R 245 (9.65)
1b
c
d
M20 x 1,5
M20 x 1,5
M20 x 1,5
M25 x 1,5
M20 x 1,5
1Back view
2 Leave at least 100 mm (3.94 in) distance for the cable gland and cable
radius
3Side view
4Front view
Figure 9: Dimensions in mm (in)

16 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 5 Installation
… Dimensions
Electronic unit EBN861 (Contrac)
M10187
100 (3.94)
35 (1.38) 75 (2.95)
97,5 (3.84)
386 (15.20)
444 17.48)
370 (14.57)
399 (15.71)
30 (1.18) 30 (1.18)
339 (13.35)
262 (10.31)
36 (1.42)
20 (0.79)
29 (1.14)
470 (18.50)
35 (1.38)
600 (23.62)
9 (0.35)
c
b
a
1Front section open, rotated 90°
2Rotational radius
3 Tap holes
Figure 10: Dimensions in mm (in)
Change from one to two columns

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 17
6Electrical connections
Safety instructions
WARNING
Risk of injury due to live parts!
When the housing is open, contact protection is not provided
and EMC protection is limited.
• Before opening the housing, switch off the power supply.
WARNING
Danger due to electric current!
Danger of electric shock by residual voltage at the terminals
after switching off the power supply.
• Before opening the terminal compartment, switch off the
power supply and wait for > 2 minutes.
NOTICE
Damage to the device due to improper handling!
• When replacing the defective safety fuses, only fuses with
types and characteristics should be used (see Fuses on
page 39).
The electrical connection may only be established by authorized
specialist personnel.
Notices on electrical connection in this instruction must be
observed; otherwise, electric safety and the IP-rating may be
adversely affected.
Safe isolation of electric circuits which are dangerous if touched
is only guaranteed when the connected devices fulfill the
requirements of EN 61140 (basic requirements for secure
separation).
To ensure safe isolation, install supply lines so that they are
separate from electrical circuits which are dangerous if touched,
or implement additional isolation measures for them.
Each actuator requires a suited Contrac electronic unit with
installed actuator-specific software. Observe the information in
the operating instruction. The specifications on the name plates
of the electronic unit and actuator must match to guarantee
correct hardware and software allocation.
Instructions on the use of Error Current
Circuit Breakers (RCDs)
If additional protection against accidental contact due to the
use of an RCD is required by local regulations, the following
items should be observed:
• For the electronic unit EBS822, the use of a type B RCD is
not necessary, since from a design viewpoint, no voltage
levels > 60 V DC which can be dangerous upon contact
can occur.
• The use of a Type B RCD is recommended for the
electronic units EBS852 and EBS862.
• The operator is responsible for the correct layout of
additional protection against accidental contact due to
the use of an RCD!
General
Each actuator requires a suited Contrac electronic unit with
installed actuator-specific software.
Conductor cross-section on universal plug
Actuators with integrated electronic unit LME620-AI / PME120-AI
Crimp pins
Mains max. 1.5 mm2(16 AWG)
Signals max. 0.5 mm2(20 AWG)
Contact surface Gold-plated
Actuators with integrated electronic unit LME620-AI / PME120-AI
Screw terminals (optional)
Power supply, signals 0.2 to 2.5 mm2(24 to 14 AWG)
Contact surface Gold-plated

18 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
hange from two to one column
… 6 Electrical connections
… Conductor cross-section on universal plug
PME / LME
Crimp pins Screw terminals (optional)
Separate
electronic unit
Cable cross-section Motor / brake / heater:
Signals:
max. 1.5 mm2(16 AWG)
max. 0.5 mm2(20 AWG)
Motor / brake / heater /
signals:
0.2 to 2.5 mm2
(24 to 14 AWG)
Contact surface Motor / brake / signals:
Heater:
Gold-plated
Silver-plated
Motor / brake / signals:
Heater:
Gold-plated
Silver-plated
integrated
electronic unit
Cable cross-section Power supply:
Signals:
max. 2.5 mm2(14 AWG)
max. 0.5 mm2(20 AWG)
Power supply / signals: 0.2 to 2.5 mm2
(24 to 14 AWG)
Contact surface Power supply /signals: Gold-plated Power supply /signals: Gold-plated
Change from one to two columns
Conductor cross-section on electronic unit
EAN823 – screw terminals
Motor/brake rigid: 0.2 to 6 mm2(24 to 10 AWG)
flexible: 0.2 to 4 mm2(24 to 12 AWG)
Mains rigid: 0.5 to 6 mm2(20 to 10 AWG)
flexible: 0.5 to 4 mm2(20 to 12 AWG)
Signals rigid: 0.5 to 6 mm2(20 to 10 AWG)
flexible: 0.5 to 4 mm2(20 to 12 AWG)
EBN853 – Screw terminals
Motor/brake rigid: 0.2 to 6 mm2(24 to 10 AWG)
flexible: 0.2 to 4 mm2(24 to 12 AWG)
Mains rigid: 0.5 to 6 mm2(20 to 10 AWG)
flexible: 0.5 to 4 mm2(20 to 12 AWG)
Signals rigid: 0.5 to 4 mm2(20 to 12 AWG)
flexible: 0.5 to 2.5 mm2(20 to 14 AWG)
EBN861 – Screw terminals
Motor / brake rigid: 0.2 to 6 mm2(24 to 10 AWG)
flexible: 0.2 to 4 mm2(24 to 12 AWG)
Mains rigid: 0.5 to 6 mm2(20 to 10 AWG)
flexible: 0.5 to 4 mm2(20 to 12 AWG)
Signals rigid: 0.5 to 4 mm2(20 to 12 AWG)
flexible: 0.5 to 2.5 mm2(20 to 14 AWG)
Cable glands
The actuators and electronic units are supplied without cable
glands. Suited cable glands must be installed on site.
Tap holes for cable glands
metric optional adapters for*
Signal cable M20 × 1.5 (2 ×) PG 16 (2 ×) NPT ½ in (2 ×)
Motor cable M25 × 1.5 (1 ×) PG 21 (1 ×) NPT ¾ in (1 ×)
* Adapter for PG or NPT thread must be ordered separately
Selection of suited connection cables
Please observe the following information when selecting cables:
• Use shielded cables for the motor/brake cable, the
sensor cable, and the signal cable to the control
system/controller.
• Connect the shielding of the motor/brake cable and the
sensor cable on both sides (to the actuator and to the
Contrac electronic unit).
Change from tw o to one column

LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E 19
Integrated electronic unit for PME120-AI / LME620-AI
Analog / digital
Note
The electrical connection is established via a universal plug on the actuator.
M11056
+1 -2
RB
+ -
Uv
24V
24V
+9 -10
RB
+ -
+11 -12
I
U
15 16 17 19 20 21 +22 -2318
113
PE
+3 -4
+5 -6 +7 -8
109876
12345
LNPE
Contrac actuator
Screen connected to both ends
one-sided screening
in further wiring possible
Transmitter
4 ... 20 mA
Setpoint
+ HART
0/4 ... 20 mA
act. pos.
0/4 ... 20 mA
DO 1
o.k./fault
DO 2
endpos.
0%
DO 3
endpos.
100%
DI 1
/MAN AUT
DI 2
(+)MAN
DI 3
(-)MAN
Uv
out
Sub distribution board
external
fuse
115 V /AC
230 V AC
HAN 10E
plug
HAN 24E
plug
option
BE = digital input
BA = digital output
Figure 11: Control via analog input 0/4 to 20 mA, HART® communication or digital inputs

20 LME620-AI / PME120-AI / EAN823 / EBN853 / EBN861 ELECTRONIC UNIT | OI/PME/LME/EAN823/EBN853/EBN861-EN REV. E
… 6 Electrical connections
… Integrated electronic unit for PME120-AI / LME620-AI
PROFIBUS DP
Note
The electrical connection is established via a universal plug on the actuator.
M10250
113
PE
LNPE
11 12 13 10
S1
BA BA
Contrac actuator
Screen connected to both ends
one-sided screening
in further wiring possible
Sub distribution board
external
fuse
115 V /AC
230 V AC
HAN 24E
plug
Bus connection
Bus in Bus out
DO 1
endpos.
0%
DO 2
endpos.
100%
Bus termination
red
green
red
green
BA = digital output
Figure 12: Control via fieldbus PROFIBUS DP®