ABB 6AGC085345 User manual

—
MANUAL
Pedestal for Terra AC wallbox
Installation manual
• TAC pedestal single (ABB6AGC085345)
• TAC pedestal back-to-back (ABB6AGC085684)
— Pedestal for Terra AC wallbox Installation manual

2PEDESTAL FOR TERRA AC WALLBOX

INSTALLATION MANUAL 3
Warning!
Not observing the safety instructions can result
in risk of death, injuries and damage to the de-
vice! The producer assumes no liability for claims
resulting from this!
Electrical hazard!
The installation, commissioning and maintenance
of the charging station may only be performed by
correctly trained, qualified and authorized
electricians who are fully responsible for the com-
pliance with existing standards and installation
regulations.
Observe the instructions given for selecting the
location and the constructional requirements!
If the specifications for the location are not ob-
served, this can result in death, serious physical
injury or equipment damage if the corresponding
precautionary measures are not met!
—
Safety instructions
This installation manual is intended for qualified
personnel only.
This guide is a supplement to the "Terra AC wall-
box Installation Manual." The information and in-
structions in the manual about selecting the loca-
tion, installation and connection of the charging
station must be adhered to.
(1) Persons who, due to their special training, expertise and experience as well as knowledge of current standards, are able to assess the work
performed and the possible hazards.
—
Use of this manual

4PEDESTAL FOR TERRA AC WALLBOX
—
Intended use
A pedestal for free-standing installation in inside
or outside areas is available as an alternative to
mounting the charging station on a wall.
Depending on the design and number of charging
stations the relevant number of empty pipes and
connection cables should be taken into consider-
ation in the concrete foundation.
If the charging station is installed with a plug-in
power supply line (e.g., for demonstration pur-
poses), you should ensure that there is sufficient
tension relief and edge protection for the power
supply line.
The respective national regulations must be ob-
served with regard to the installation of the
pedestals.
Weight (without charging station): 10,5 kg (single
/ back-to-back)
TAC Pedestal Single

Back-to-Back Pedestal

 SCREW; FLAT HEADED

Stainless steel
 SCREW; FLAT HEADED

Stainless steel
 


 


   
   
   

INSTALLATION MANUAL 5
—
Overview
—

The single pedestal is designed for the
installation of one charging station.
—

The back-to-back pedestal is designed for
the installation of two charging stations.

No Yes
6PEDESTAL FOR TERRA AC WALLBOX

• All of the location requirements for the
charging station in the " Installation manual"
must be adhered to!
• When mounting the pedestals in parking spaces
or parking garages, appropriate anti-collision
protection must be provided by the customer.

• The calculation, design and manufacture of the
concrete foundation lies in the scope of
responsibility of the producer of the site.
• A horizontal, level and sound foundation is
required for installation.
To ensure safe and permanent anchoring, we
recommend creating a concrete foundation:

Concrete: C30/37
• The base must permit the running off of any
water that has entered the base.
• All cables must be laid precisely in the centre of
the concrete foundation from the base and
must have an excess length of approx. 1.5 m for
the remaining installation activities.
• During the production of the concrete
foundation, the cables must be protected
against damage using appropriate measures
(e.g., a protective tube). The protective tube
must have an excess length of approx. 25 cm
above the concrete foundation.
• Mounting the pedestal on asphalt is not
allowed!
—
Warning
—
Location requirements
Electrical hazard!
The back-to-back pedestal must always be fitted
with two charging stations!

INSTALLATION MANUAL 7
—
Positioning the base
200
1306
700
500 100
600
100
500 1306100
Position the base below street level. The pavement can cover the base. See drawings below.

PEDESTAL FOR TERRA AC WALLBOX
The 4x anchors (M10x40) must be used for
anchoring.
—
Technical data
Anchorage ground Standard concrete
with a strength class of


Recommended load Tension N (uncracked
concrete)

Per anchor Transversal shear V
(uncracked concrete)

Required clearance 
Max.Torque Tinst 
Drill-hole diameter do 
 
Making drill holes
• Mark the 4 holes on the concrete foundation
using the base plate of the pedestal. Make sure
that the connection cable is located precisely
underneath the opening in the base plate.
• Drill the 4 mounting holes:
Diameter: 12 mm
Drill-hole minimum depth: 43 mm
• Hammer the anchors (not included) so that
they are flush with the floor.
Please also observe the following instructions:
Instructions on inserting the anchors
—
Anchoring to the base
Tinst
lg
d0
h1
I=hnom

INSTALLATION MANUAL 9
345mm
200
1406 mm
245 mm
100
4x
14
200
22,5
300 22,5
200
C
DETAIL C
SCALE 1 : 2

• Thread the connection cables from the bottom
through the pedestal upwards through the
cable opening.

• Position the pedestal directly over the cable
outlet.
• Anchor the pedestal to the foundation using 4
bolts M10 and washer M10 (not included).
NOTE
THE IMAGES ARE VALID FOR ALL VERSIONS.
Pedestal from
below
200
300
A
ISO 4017-
M12x 35
DIN125 -
Washer

 PEDESTAL FOR TERRA AC WALLBOX
Grounding point

• If necessary, connect the earthing to the
pedestal's grounding point with included

Max torque: 4 Nm.
Add edge cable protection
• Add the edge protection on the cable
opening of the pedestal immediately before
installing the charging station (see figure).
• 
345
245
200
300
A
DETAIL A
SCALE 1 : 2
ISO 4017-
M12x 35
DIN125 -
Washer
B
DETAIL B
SCALE 1 : 2
345
245
200
300
A
DETAIL A
SCALE 1 : 2
ISO 4017-
M12x 35
DIN125 -
Washer
B
DETAIL B
SCALE 1 : 2
345mm
200
1406 mm
245 mm
100
4x
14
200
22,5
300 22,5
200
C
DETAIL C
SCALE 1 : 2

INSTALLATION MANUAL 11
Mounting the charging stations
• Mount the charging stations on the pedestal
using the enclosed screws.
• Use for top; screw type flat headed DIN 923

• 

Connecting and commissioning
• Perform the electrical connection and
commissioning in accordance with the
instructions in the “Installation manual.”
345
245
200
300
A
DETAIL A
SCALE 1 : 2
ISO 4017-
M12x 35
DIN125 -
Washer
B
DETAIL B
SCALE 1 : 2

12 PEDESTAL FOR TERRA AC WALLBOX
—
Single pedestal
ABB6AGC085345
200
1406 mm
345 mm
100
245 mm
200
300 22,5
22,5
4x 14

INSTALLATION MANUAL 13
—
Back-to-back pedestal
ABB6AGC085684
345mm
200
1406 mm
245 mm
100
4x
14
22,5
300 22,5
200

© Copyright 2020 ABB. All rights reserved.
Specifications subject to change without notice.
9AKK107991A5012 rev A - (11/2020)
—
ABB
Heertjeslaan 6,
2629 JG Delft
Netherlands
