ABB SPA 650 Series User manual

RELION® 650 SERIES
—
SPA, 650 series
Version 2.2
Communication protocol manual

Document ID: 1MRK 511 418-UEN
Issued: October 2017
Revision: A
Product version: 2.2.1
© Copyright 2017 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license
and may be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/) This product includes cryptographic
software written/developed by: Eric Young ([email protected]) and Tim Hudson
([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure
and/or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole
responsibility of the person or entity applying the equipment, and those so
responsible are hereby requested to ensure that all measures are taken to exclude or
mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standard EN 60255-26 for the EMC directive, and
with the product standards EN 60255-1 and EN 60255-27 for the low voltage
directive. The product is designed in accordance with the international standards of
the IEC 60255 series.

Table of contents
Section 1 Introduction.......................................................................3
This manual........................................................................................ 3
Intended audience.............................................................................. 3
Product documentation.......................................................................4
Product documentation set............................................................4
Document revision history............................................................. 5
Related documents........................................................................6
Document symbols and conventions..................................................7
Symbols.........................................................................................7
Document conventions.................................................................. 8
Section 2 SPA application..............................................................11
SPA communication protocol........................................................... 11
Application................................................................................... 11
Setting guidelines........................................................................ 12
Section 3 SPA operation principle..................................................13
Operation principle........................................................................... 13
Introduction of SPA protocol........................................................13
SPA protocol................................................................................13
I/O modules............................................................................ 14
Single command, 16 signals ................................................. 14
Event function EVENT............................................................17
Connection of signals as events.............................................18
Communication ports...................................................................18
Design.............................................................................................. 19
Section 4 SPA settings...................................................................21
Settings.............................................................................................21
Section 5 SPA technical data.........................................................23
Technical data.................................................................................. 23
Section 6 Establishing connection and verifying the SPA/IEC
communication............................................................... 25
Establishing connection and verifying the SPA/IEC
communication ................................................................................ 25
Entering settings..........................................................................25
Entering SPA settings............................................................ 25
Verifying the communication....................................................... 26
Verifying SPA communication................................................ 26
Table of contents
650 series 2.2 IEC 1
Communication protocol manual

Fibre optic loop............................................................................ 26
Optical budget calculation for serial communication with
SPA/IEC ..................................................................................... 26
Section 7 SPA functions.................................................................29
Event function EVENT......................................................................29
Identification................................................................................ 29
Function block............................................................................. 29
Signals.........................................................................................30
Settings........................................................................................31
Operation principle...................................................................... 33
Setting guidelines............................................................................. 34
EventMask (Ch_1 - 16)................................................................34
LONChannelMask or SPAChannelMask .....................................34
MinRepIntVal (1 - 16).................................................................. 35
Logical signal status report BINSTATREP....................................... 35
Identification................................................................................ 35
Functionality................................................................................ 35
Function block............................................................................. 35
Signals.........................................................................................36
Settings........................................................................................37
Operation principle...................................................................... 37
Section 8 Glossary......................................................................... 39
Glossary........................................................................................... 39
Table of contents
2650 series 2.2 IEC
Communication protocol manual

Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v18
The communication protocol manual describes the communication protocols
supported by the IED. The manual concentrates on the vendor-specific
implementations.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v11
This manual is intended for the communication system engineer or system
integrator responsible for pre-engineering and engineering the communication
setup in a substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1MRK 511 418-UEN A Section 1
Introduction
650 series 2.2 IEC 3
Communication protocol manual

1.3 Product documentation
1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15
IEC07000220-4-en.vsd
Planning & purchase Engineering Installing Commissioning Operation Maintenance Decommissioning Deinstalling & disposal
Application manual
Operation manual
Installation manual
Engineering manual
Communication
protocol manual
Cyber security
deployment guideline
Technical manual
Commissioning manual
IEC07000220 V4 EN-US
Figure 1: The intended use of manuals throughout the product lifecycle
The engineering manual contains instructions on how to engineer the IEDs using
the various tools available within the PCM600 software. The manual provides
instructions on how to set up a PCM600 project and insert IEDs to the project
structure. The manual also recommends a sequence for the engineering of
protection and control functions, LHMI functions as well as communication
engineering for IEC 60870-5-103, IEC 61850, DNP3, LON and SPA.
The installation manual contains instructions on how to install the IED. The
manual provides procedures for mechanical and electrical installation. The chapters
are organized in the chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED.
The manual can also be used by system engineers and maintenance personnel for
assistance during the testing phase. The manual provides procedures for the
checking of external circuitry and energizing the IED, parameter setting and
configuration as well as verifying settings by secondary injection. The manual
Section 1 1MRK 511 418-UEN A
Introduction
4650 series 2.2 IEC
Communication protocol manual