Abbott AMPLATZER Sizing Balloon II Series User manual

1
Manufacturing facility:
Abbott Medical
5050 Nathan Lane North
Plymouth, MN
55442 USA
[phone]
[phone]
ARTEN600038218A
2018-08
™ Indicates a trademark of the Abbott group of companies.
‡ Indicates a third party trademark, which is property of its respective owner.
Pat. http://www.abbott.com/patents
© 2018 Abbott. All Rights Reserved.
Device Description
The AMPLATZER™ Sizing Balloon II is a triple lumen balloon catheter with three (3) radiopaque marker bands located inside
the balloon to allow for radiographic measurement. The center of the balloon contains a pair of marker bands 0.4 mm apart
(inside to inside), and one (1) marker band 15 mm proximal of that pair (15 mm from the proximal edge of the pair of marker
bands) (figure 1).
Intended Use
The AMPLATZER™ Sizing Balloon II is designed to measure cardiovascular structures. Sizing can be accomplished in two
ways: radiographically or echocardiographically.
Indications for Use
The AMPLATZER™ Sizing Balloon II is indicated for use in those patients with cardiovascular defects wherein accurate
measurement of the defect is important in selecting the appropriately sized occluder device.
Precautions and Warnings
• This device was sterilized with ethylene oxide and is for single use only. Do not reuse or resterilize this device. Attempts to
resterilize this device can cause a malfunction, insufficient sterilization, or harm to the patient.
• Do not use this device if the sterile package is open or damaged.
• Use on or before the last day of the expiration month that is printed on the product packaging label.
• Do not insert the balloon catheter through an introducer sheath.
Figure 1. AMPLATZER™ Sizing Balloon II
Sizing Balloon II
Instructions for Use

2
• This device should be used only by physicians who are trained in standard transcatheter techniques. The physician should
determine which patients are candidates for procedures that use this device.
• Store in a dry place.
Adverse Events
Potential adverse events that may occur during or after a procedure using this delivery system may include, but are not limited
to:
Potential complications specific to balloon sizing include:
• Movement of the balloon toward the mitral valve or right atrium
• Enlargement of the ASD
• Obstruction of venous return from the inferior vena cava
• Difficulty in deflating the balloon
Defect sizing information is provided in table 1, and device dimensions are provided in table 2.
Directions for Use
Recommendations on Guidewire and Balloon Use
The guidewire must remain in place during the procedure. The removal of the guidewire during the procedure can cause kinking
and/or migration of the sizing catheter. The maximum inflation volume of the balloon should not be exceeded to prevent over-
inflation, bursting or detachment of the balloon.
Procedure
Carefully inspect the sterile pouch and verify that it is unopened and undamaged. Gently open the sterile pouch and inspect the
balloon catheter prior to use to verify that it is undamaged. Slowly slide the protective cover off the balloon segment. Avoid acute
bends or kinking of the AMPLATZER™ Sizing Balloon II during removal from the packaging.
The procedure will vary according to the type of occlusion or measurement to be performed. Because of the ultra thin plastic
membrane, dilatation of the entry site is not necessary.For the measurement of secundum atrial septal defects, the following
steps are recommended:
• Arrhythmia • Short-term hemodynamic compromise
• Cardiac obstruction • Stroke
• Death • Thromboembolic event
• Embolization • Valve impingement
• Endocarditis • Vascular thrombosis
• Hematoma • Vessel dissection
• Oversizing of the defect • Vessel perforation
• Pain and tenderness • Vessel spasm
• Sepsis/Infection
Table 1. Defect sizing parameters
Reference
Number
Maximum
Defect Size
mm
Maximum Inflation
Volume
cc
Balloon
Length
cm/mm
9-SB-018 20 15 3.5/35
9-SB-024 27 30 4.5/45
9-SB-034 40 90 5.5/55
Table 2. Device dimensions
Reference
Number
Shaft
Size
Fr
Usable
Length
cm/mm
Guidewire
in
9-SB-018 6.0 70/700 0.035
9-SB-024 7.0 70/700 0.035
9-SB-034 8.0 70/700 0.035

3
1. Inflate the balloon with saline solution and purge the air in a position as shown in figure 1 or inflate with CO2 and
aspirate. Flush the other lumen with heparinized saline.
2. Manipulate a 0.035 inch stiff exchange wire into the left upper lobe pulmonary vein. Introduce the balloon catheter over
the guidewire.
3. Introduce the balloon catheter over the exchange wire transcutaneously.
4. Advance the collapsed balloon through the defect. Position the sizing catheter to center the balloon in the
communication.
5. Partially inflate the balloon with contrast medium (diluted 3:1 or 4:1).
6. Observe the patient in a shallow left anterior-oblique position without cranial angulation.
7. Gradually move the imaging source to visualize the 0.4mm space between the pair of marker bands in the center of the
balloon (figure 2). This aligns the imaging source with the balloon to achieve the best angle for size measurement.
8. Inflate the balloon until the right-to-left shunt ceases and a stop-flow condition is observed by Doppler observation.
Slightly deflate the balloon, and gradually re-inflate to the minimum balloon diameter that achieves a stop-flow condition.
A minimal balloon “waist” may or may not be present.
WARNING: Do not inflate the balloon beyond the stop-flow point or beyond the balloon’s maximum inflation volume.
Inflation beyond the stop-flow point may cause distention of the defect resulting in inaccurate sizing of the defect and/or
balloon damage.
9. Using echocardiography, adjust the image for best visualization, and measure the minimum diameter between the septal
wall contact points with the balloon (figure 3). If a balloon waist is detected, radiographic measurement may also be used
to confirm defect diameter.
10. Forcefully aspirate all of the contrast medium and then remove the balloon catheter.
Proceed with recommended implantation protocol for the device.
Figure 2. Balloon alignment
Figure 3. Minimum diameter measurement

4
Disposal
• The instructions for use are recyclable. Dispose of all packaging materials appropriately.
• Dispose of delivery systems and accessories following standard solid biohazard waste procedures.
Warranty
Abbott Medical warrants to buyer that, for a period equal to the validated shelf life of the product, this product shall meet the
product specifications established by the manufacturer when used in accordance with the manufacturer's instructions for use
and shall be free from defects in materials and workmanship. Abbott Medical's obligation under this warranty is limited to
replacing or repairing at its option, at its factory, this product if returned within the warranty period to Abbott Medical and after
confirmed to be defective by the manufacturer.
EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, ABBOTT MEDICAL DISCLAIMS ANY REPRESENTATION OR
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY AS TO MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
See the Terms and Conditions of Sale for further information.
State of California (USA) Only:
WARNING: This product can expose you to chemicals including ethylene oxide, which is known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

5
Symbol Definitions
The following symbols may appear on the device packaging:
Symbol Definition
Caution, consult accompanying documents
Manufacturer
EU authorized representative
Reference number
Product serial number
Batch Code
Use by date
(Use on or before the last day of the expiration month noted on the product packaging.)
Do not reuse
Sterilized using ethylene oxide
Unique device identification
Consult instructions for use
Follow instructions for use on this website
Keep dry
Do not use if package is damaged
Not made with natural rubber latex
Inner diameter
Outer diameter
Length
Usable length

6
Hydrophilic coating
Recommended delivery sheath/catheter dimensions
Federal law (USA) restricts this device to sale by or on the order of a physician (or properly licensed
practitioner).
Contains phthalate
Quantity
Date of manufacture
Sizing Balloon
ONLY
Sizing Balloon