abi SOLA OUTDOOR SHOWER SET User manual

S O LA O UTDO O R S HO W E R SET
Dis cla imer: P ro d u c ts in th is ma n u a l mu s t by la w b e in s talled b y licen s ed an d reg is tered tra d es p eo p le in a cco rd a n ce w ith th e releva n t stan d a rds . A B I a n d th e ma n u fa ctu rer/d is trib u to r
res erve t h e rig h t to va ry s p ecif ic a tio n s o r d elete mo d els fro m t h eir ra n g e w ith o u t prio r n o tif ic a t io n . Dimen s io n s a re n o min a l mea s u remen ts o n ly. Th e in f o rma tio n lis t ed is co rrect at th e time
o f p u b lica tio n , h o w ever A B I a n d th e man u f a c tu rer/d is trib u to r ta kes n o res p o n s ib ility fo r p rin tin g erro rs. C o p yrig h t © A B I I n terio rs 2 02 2 Pty Ltd
SPECIFICATIONS
RECOMMENDED USE Domestic
MATERIAL 316 Stainless Steel
TEMPERATURE RATING Maximum continuous working temperature 75°C
If the water temperature exceeds 75°C,an approved tempering
valve must be fitted
PRESSURE RATING Recommended minimum working pressure 150kPa
Recommended maximum working pressure 500kPa
Hot and cold water inlet pressure should be equal
SUITABLE HOT WATER UNITS Storage tank: Yes
Continuous Flow: Yes
Gravity Feed: Not suitable
STANDARDS Overhead Shower: WELS 3 star, 9L/min, Hand Shower: WELS 3 star,
8.5L/min, S16553
AS/NZS 3718:2005
WM-021226

INSTA LLATION GUIDE
Note:Drainage not shown, please ensure dra inag e
is compliant with yourlocal standard
Important!
There are m any installation options for this product. Werecommend consulting
your designer or p lumber prior to commencing a ny works to determinethe most
appropriate m ethod for you.Please note this product must not be installed
encased in concrete to allow access to water connections.See examples of
cor r ect installation methods below. ABI's warranty is void if this product
is installed incorrectly or encased in concre t e.
Installation on top of
concrete sla b
with timber decking
This installation in shown in
the following Install Guide
Installation on top
of concrete sla b
withfine stone fi l l ,
decorative stone
and removable
paving
Installation on top
of concret e sla b
with fine stone fil l
and decorative stones
ABI' S WARRANTY IS VOID I F
THIS PRODUCT IS INSTALLED
INCORRECTLY OR ENCASED
IN CONCRETE.
WA RNING!
Note:Drainage not shown, pleaseensure drainage
is compliant with your local standard
Important!
There are many installation options for this product. We recommend consulting
your designer or plumber prior to commencing any works to determine the mos t
appropriate m ethod for you.P lease note this product must not be installed
encased in concrete to allow access to water connections.See examples of
correct installation methods below. ABI's warranty is voidif this product
is installed incorrectly or encased in concrete.
Installation on top of
concrete slab
with ti mber decki n g
This installation in shown in
the followingInstall Guide
Installation on top
of concrete slab
withfine stone fill ,
decorative stone
and removable
paving
Installation on top
of concrete slab
with fine stone fill
and decorative stones
ABI'S WARRANTY IS VOID IF
THIS PRODUCT IS INSTALLED
INCORRECTLY OR ENCASED
IN CONCRETE.
WA RNING!
Note: This product must be installed by a licensed plumber. This is a general installation guide - there are many factors involved that
can alter the installation method. AU/NZ: For installations within Australia and New Zealand, this product must be installed in
compliance with AS/NZS 3500. UK: For installations in the United Kingdom this product must be installed in compliance with the
Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. Other: For installations outside
these countries, this product must be installed in compliance with the standards in your respective country.

1. Use the base as a template to mark holes.
2. Place lid on top to ch eck level. Double check
your position is correc t.
1
1. Tighten nuts to secure basedown.
2. Attach hot and coldwaterpipes (use
appropriate thread sealant).
3
5Attach and bolt body to base. 6
1. Trim plastichousing to bel evel with floor
structure(if required).
2. Securewater pipes appropriately.
4
1. Rem ove b ase, drill theholes intothe
concrete footingto a depth of 60mm.
2. Insert dyna bolts.
CONCRETE FOOTING
2
1.
1.
1.
1.
2.
2.
2.
Hot
Co ld
2.
60
Co nnect shower headto Arm.
1. Usethe base as a template to mark holes.
2. Placelid on top to check level. Double check
your position is correct .
1
1. Tighten nuts to secure base down.
2. Attach hot andcold water pipes (use
appropriate thread sealant).
3
5
Attach and bolt body to base.
6
1. Trim plastic housing to belevel with floo r
structure(ifrequired).
2. Secure water pipes appropriately.
4
1. Remove base, drill the holes intothe
concrete footing toa depth of60mm.
2. Insert dyna bolts.
CONCRETE FOOTING
2
1.
1.
1.
1.
2.
2.
2.
Ho t
Cold
2.
60
Co nnect shower head toArm .

2.
2.
1. Attach floor covering.
2. Push cover platedown.
7
1.
1.
1.
2.
8
Connect Arm to Body .
1. Connect internal flexi-hoses.
2. Push together and usean alan key to fasten
set screw.
* Test an d check all water points for leaks.
91. Attach han d held shower head .
2. Test and commission.
2.
2.
1. Attach floor covering.
2. Push cover plat e down.
7
1.
1.
1.
2.
8
Connect Arm to Body.
1. Connect internal flexi-hoses.
2. Push together and use an alan key to faste n
set screw.
* Test and ch eck all water points for l eaks.
91. Attach handhe ld shower head .
2. Test and commission.
Front View
Top View
Side View
180
180
113
3848
8
31
93
Base Connection

*ENLARGED PARTS
1
2
9
12 1 3
10
11
3
4
5
7
8
6
In the box
1. Bas e
2. Li d
3. Cover Plate
4. Body
5. Arm
6. Shower Hea d
7. Hand-held Shower Head
8. Hose
9. Set Scr ew
10 . 20mm Bolt
11. 90mm DynaBolt set
12 . Alan key 6mm
13 . Alan key 3mm
x6
x1 0
*ENLARGED PARTS
1
2
9
12 1 3
10
11
3
4
5
7
8
6
In the box
1. Bas e
2. Lid
3. Cover Plate
4. Body
5. Arm
6. Show er Head
7. Hand-hel d Shower Head
8. Hose
9. Set Screw
10. 20mm Bol t
11. 90mm DynaBolt set
12. Alan key 6mm
13. Alan key 3mm
x6
x1 0
DO NOT use crea m
cleaners or bleach.
Thesesubstances are
abrasive .
Regularlyclean with
mildliquid deterg e n t
or soap and water.
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the materia l .