ABSCO SHEDS 30302GK User manual

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 1
Download the Absco
Sheds Assembly App
for instructional videos
MANU FA CT URED
IN A US TR ALIA
SNAPTiTE
Assemb ly
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
When laying concrete slab, ensure there
is a rebated edge 25mm deep around the
perimeter. This will help water egress from
the base of the shed.
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2012
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
CONCRETE SLAB
3100mm
3100mm

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit 10mm drill bit metal/masonry

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 3
COMPONENT PACKING LIST
Check off all components.
STEEL SHEET
1785mm X 773mm 30A
2
STEEL SHEET
1785mm X 773mm 31A
2
STEEL SHEET
1915mm X 773mm 36L
2
STEEL SHEET
1915mm X 773mm 36R
2
15A
2
PEAK BRACE
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
STEEL SHEET
1785mm X 711mm 34A
2
STEEL SHEET
1725mm X 773mm A
1
STEEL SHEET
2045mm X 773mm 38R
2
STEEL SHEET
1546mm X 773mm 45A
8
STEEL SHEET
2045mm X 773mm 38L
2
STEEL SHEET
1725mm X 773mm B
1
97AL
1RIDGE
BEAM
1
L = 1521mm (59.9")
97AR
RIDGE
BEAM
L = 1521mm (59.9")
ZARSP
1RIDGE BEAM JOINER
L: 450mm (17.7")

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 4
COMPONENT PACKING LIST
58C
4CHANNEL
L = 773mm
2CHANNEL
L = 1518mm
84R 2CHANNEL
L = 1518mm
84L
58B
1CHANNEL
L = 1725mm
58A
2CHANNEL WITH HINGES
L = 1725mm
79A
1CHANNEL
L = 1568mm
55AL
55CL
55BL
81BL
81AL
60AL
55CR
1
1
1
1
4
2
1
1
1
1
4
2
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
55BR
81BR
81AR
60AR
55AR
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 5
COMPONENT PACKING LIST
90A
JAMB L= 1568mm
191A
JAMB L= 1120mm
4
87A
LIP TRIM L= 1546mm
4
14A
2CAP GABLE
L: 170mm
1ASSEMBLY
INSTRUCTIONS
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
INSTRUCTIONS & FITTINGS PACKET
89C
JAMB L= 1725mm
1
89A
JAMB L= 1785mm
2
12A
2
DOOR
STRAP
L: 165mm
CSJ
10 CHANNEL JOINER
L= 200mm (7.9")
DOOR
PADBOLT
HASP
2
3
SELF TAPPING SCREWS
PACKET CONTAINING 220
1
DOOR
PADBOLT
3/16 COUNTERSUNK
SCREWS & NUTS
12
3/16 ROUND HEAD
BOLTS & NYLOCK NUTS
83.2 x 8mm
BLIND POP RIVETS
12
PSTKDBL - DOUBLE DOOR FITTINGS PACK
PACK12P - SCREW PACK 12
PACK12P
SCREW PACK 12
1
PHILLIPS DRIVER BIT
3mm DRILL BIT DRILL FAST038
FAST007FAST006
10 16mm TEK
SCREWS FAST014
1 1
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 100
PSTKDBL
DOUBLE DOOR FITTINGS PACK

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 6
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 7
Guide on Joining Spliced Channels
The text marked on all parts must be shown on the same side as each other
Step 1.
Position the channels and the
CSJ joiner so the centre of
the CSJ is in line with the end
of each channel to be joiner
together.
Step 2.
Join the first channel to the CSJ
by inserting the centre of the
CSJ, on an angle, to the end of
the channel where the JOIN>>
text is marked.
Push down one side of the CSJ
until you hear a ‘click’.
Step 3.
Join the second channel to the
CSJ by positioning the <<JOIN
of the channel at the centre of
the CSJ, on an angle. Push the
CSJ into the channel until you
hear a ‘click’.
Finished Channel.
The joined channels should
now look like the picture with
the CSJ positioned equally
inside of the joined channels.
Drill out holes with 3mm drill
bit in CSJ to match the holes
in channel and secure with the
screws supplied.
These may have to be
temporarily removed during
assembly.
= =
JOIN>> <<JOIN
CSJ
==
JOIN>>
J
==
JOIN>> SJ
= =
JOIN>>
<<JOIN
= =
JOIN>> <<JOIN
Finished Spliced
Channel
Channel
Push
20mm 15mm
CSJ
.
...

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 8
PRE-ASSEMBLY OF SPLICED CHANNELS
NOTE: Some channels may have holes in them - You will
need to redrill holes where CSJ joining channel covers
them.
Join together 16 x channel sections using 8 x channel joiners (Part CSJ)
4x 81AR
4x 81AL
2x 60AR
2x 60AL
1x 55AR
1x 55AL
1x 55CR
1x 55CL
1x 55BR
1x 55BL
1x 81BR
1x 81BL
2993mm
81BL
55BL
55CL
55AL
60AL
81AL
81BR
55BR
55CR
55AR
60AR
81AR
= 4x 81A
= 2x 60A
= 1x 55A
= 1x 55C
= 1x 55B
= 1x 81B

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 9
Tek screw driver bit
Push
Guide on Joining a Spliced Ridge Beam
Follow these three steps to assemble a ridge beam.
Step 1.
Place two ridge beams as
shown and push them together.
Slide the cap of one under the
other.
NOTE.
There is a 50mm overlap of the
ridge caps when the beams are
in position.
Step 2.
Use the ZARSP to connect at
the centre of the two ridge
beams. Be sure it is pushed in
fully.
Step 3.
Turn over the ridge beam.
Measure 250mm from the
middle along the centre of one
ridge beam, mark spacings of
50mm. Fasten with a Tek screw
at each marking.
Repeat to the other side of the
ridge beam assembly.
TIP: Predrilling each hole with
the 3mm drill bit makes it easier
to fasten.
50mm
225mm
ZARSP
Finished Spliced Ridge Beam
Finished
Spliced Ridge Beam
ZARSP
Ridge Beam
Self drilling Tek screw

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 10
PRE-ASSEMBLY OF SPLICED RIDGE BEAM
.
.
1x 97AL
1x 97AR
= 1x 97A
2993mm Overall length
ZARSP
225mm
97AL 97AR
16mm
16mm

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 11
OVERVIEW OF ROOF COMPONENTS
OVERVIEW OF ROOF COMPONENTS
87A
60A
14A
87A
81A
87A
87A
14A
81A
97A
45A
45A
45A
45A
45A
45A
45A
45A

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 12
OVERVIEW OF WALL COMPONENTS
OVERVIEW OF WALL COMPONENTS
81A
84L
55B
84R
84L
15A
55A
30A
30A
31A
31A
81B
36L
38L
36R 34A
55C
84R
36R
34A
38R
81A
38R
38L
36L
79A
89A
89A
91A
90A
91A
B
22A
A

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 13
REAR PANEL ASSEMBLY
1x required.
30A
31A
31A
30A
55B
81B
SNAP
T
TE
i
SNAP
T
TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 14
ROOF PANEL ASSEMBLY
2x required.
Fit 81A to edge
of sheet with pre-
punched holes.
45A
45A
45A
45A
SNAP
T TE
i
SNAP
T TE
i
87A
81A
87A
60A
D
D
D
D
D
D

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 15
SIDE PANEL ASSEMBLY
2x required.
INSIDE
OF
SHED
Trim the tip of each
sheet or bend out of the
way to allow channels to
fit hard up to the edge of
the sheet.
36L
38L
38R
36R
84R
81A
84L
15A
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 16
FRONT PANEL ASSEMBLY
89A
89A
90A
79A
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
34A
5A
89A
90A
5A
89A
90A
5A
5A
79A
79A
5C
5C
89A
5
5
5
5
5
5
1x required.
34A
55A
55C

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 17
DOOR PANEL ASSEMBLY
58C
58C
58C
12A
58C
58A
58A
A
B
89C
58B
A
B
SNAP
TTE
i
SNAP
TTE
i
SNAP
TTE
i
SNAP
T TE
i
Vertical door channels are
installed in the opposite
orientation compared to the
horizontal door channels.
Four hole set for
padbolt connection.
Short flange
of channel
Long
flange of
channel
D
D
D
D
D
D
D
D
1x required.

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 18
DOOR PANEL ASSEMBLY
Nuts and bolts may be used instead of pop rivets by
drilling out hinge holes using a 4mm drill bit. Both
are supplied.
The two holes required to connect the padbolt hasp for each door have not been pre-punched, to
allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and
secure with screws.
91A
91A
A
B

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 19
PANEL CONSTRUCTION
NOTE: Take care to ensure that all wall panels
are not upside down. The top channels
of each panel are pre-punched for
attaching roof sheeting. The
base channels are not pre-
punched.
Side wall channels
fit into the
notched rear wall
channels.
Pre-punched holes in roof panel to this side
for connection to front and rear walls.
Pre-punched
channel to
match ridge
beam holes
Orient panel so
channel (60A)
goes into ridge
beam
Channel (81A)
this end
97A
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30302GK
3.00mW x 3.00mD x 2.10mH
Model: 30302GK 20/08/18 1.20 20
Secure peak brace to
ridge beam and roof
panel with one screw at
each end
INSIDE VIEW OF FIXING
Move the other roof
panel into position and
secure peak brace to
ridge beam with one
screw at each end