ABSCO SHEDS J15301FK User manual

PAGE 1
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
CONCRETE SLAB
3100mm
1620mm
We thank you for choosing an Australian made shed. For further assistance please
visit our detailed instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be number ONE, so please let us
know what you think of our instructions. Feedback makes us better.
[email protected]
FRONT: 1.52m
SIDE: 3.0m
HEIGHT: 1.80m
Absco Economy Shed
Model: J15301FK
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A REBATED
EDGE 25mm DEEP AROUND THE PERIMETER
CONCRETE
SLAB
REBATED EDGE
CHANNEL
CONCRETE SLAB
75mm WIDE
REBATE
THIS WILL HELP
WATER EGRESS FROM
THE BASE OF THE SHED
100mm

PAGE 2
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
GENERAL INSTRUCTIONS
A NOTE ON SAFETY
·The site for the shed must be level. An uneven surface may result in misalignment of
parts.
·It is recommended that the shed be set on a 100mm concrete slab and anchored down
appropriately (refer to last page for details). A flat slab with a chamfered edge can be
used but will not result in optimum results.
·Anchor sets are not supplied as standard items with this product. As some customers
wish to use their own anchoring systems
·Before commencing any assembly, read through these instructions in
detail to gain a thorough understanding of assembly methods and
associated details.
·Unpack the carton and carefully identify and check off all the parts
against the parts described and illustrated on pages three and four.
·Some parts may have sharp edges. It is advisable to wear gloves when
handling these items and safety glasses if drilling holes. Sensible shoes
are highly recommended.
·Do not erect your shed in windy conditions, ensure that the shed is
securely anchored to a solid foundation immediately after construction is
completed.
·It is highly recommended to erect the shed with two or more people.
TOOLS REQUIRED
3mm
4mm OPTIONAL
SITE PREPARATION

COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 3
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
5
5
4
1
1
1
1
1
1
4
1
1
1
1
2
1785mm X 773mm 30A
STEEL SHEET
STEEL SHEET
1785mm X 773mm 31A
STEEL SHEET
1592mm X 773mm 43A
STEEL SHEET
1785mm X 711mm 34A
STEEL SHEET
1725mm X 773mm B
81F
CHANNEL
L = 1513mm
58A
CHANNEL WITH HINGES
L = 1725mm
58B
CHANNEL
L = 1725mm
58C
CHANNEL
L = 773mm
53D
CHANNEL
L = 1513mm
53B
61C
CHANNEL
L = 1513mm
CHANNEL
L = 1513mm
80A
CHANNEL
L = 1785mm
79C
CHANNEL
L = 783mm
55BL
CHANNEL
L = 1496.5mm
2
81AL
53D
Part No. Here
ALL SHEETS HAVE PART NO.S LOCATED ON
LOWER RIGHT OR UPPER LEFT CORNER OF
COLORED SIDE AS SHOWN
53B
61C
81F
55B
81A
80A
79C
58A
58B
58C
4
55BR
2
81AR
55B
81A
CHANNEL
L = 1496.5mm
CHANNEL
L = 1496.5mm
CHANNEL
L = 1496.5mm

PAGE 4
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
CONTENTS OF FITTINGS PACKET
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
1
1
1
89A
JAMB L= 1785mm
89B
JAMB L= 1785mm
90C
JAMB L= 783mm
91A
JAMB L= 1120mm
2
88A
LIP TRIM L= 1592mm
2
6
4mm CSK SCREW &
NUT SECURE HINGES
TO DOOR
220
SELF TAPPING
SCREWS
10mm 1DOOR
PADBOLT
1
DOOR
PADBOLT
HASP
6
3mm POP RIVETS SECURE
HINGES TO DOOR
(ALTERNATIVE FIXING
METHOD)
1ASSEMBLY
INSTRUCTIONS 12A
1
DOOR
STRAP
L: 165mm
22A
6SELF TAPPING
SCREWS
20mm
Part No. Here
Part No. Here
Part No. Here
88A
Part No. Here
CSJ
6CHANNEL JOINER
L= 200mm (7.9")

20mm
15mm
QTY = 10pcs.
CHANNEL
(0.79")
(0.59")
PUSH PUSH
CHANNEL
CSJ
PAGE 5
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
INSTRUCTIONS FOR JOINING SPLICED CHANNELS
CSJ
CSJ
HIGH-SIDE
CHANNEL
LOW-SIDE
CHANNEL
CSJ
CSJ
CSJ
= =
= =
==
=
=
STEP 1.
Position the channels and the CSJ
joiner channel so the center of the
CSJ is in line with the end of each
channel to be joined together.
STEP 2.
Join the first channel to the CSJ by inserting the center
of the CSJ (on an angle) to the end of the channel
where the JOIN>> text is marked. Push down one side
of the CSJ until you hear a 'click'.
STEP 3.
Join the second channel to the CSJ
by positioning the <<JOIN end of the
channel at the center of the CSJ
(on an angle). Push the CSJ into
the channel until you here a 'click'.
=
The joined channels should now
look like the picture above with the
CSJ positioned equally inside of the
joined channels.
FINISHED CHANNEL
=
NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.
JOIN>> <<JOIN JOIN>>
JOIN>> SJ
JOIN>>
<<JOIN
JOIN>> <<JOIN
J
CSJ
DRILL 4mm (0.16") x 3mm (0.12")
(2 PER A SIDE) HOLES TO
SECURE SECTIONS TOGETHER.
(THESE SCREWS MAY HAVE TO
BE TEMPORARILY REMOVED
AND REPLACED DURING LATER
ASSEMBLY)
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS

PAGE 6
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
=
=
2993mm (117.8")
STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS
4 x 81A
2 x 55B
NOTE: JOIN TOGETHER 12 X CHANNEL SECTIONS USING 6 X CHANNEL JOINERS (PART CSJ)
55BR
55BL
81AR
81AL
4 X 81AR
4 X 81AL
2 X 55BR
2 X 55BL
NOTE: SOME CHANNELS HAVE
HOLES IN THEM - YOU WILL NEED
TO RE-DRILL HOLES ON ANY
CHANNEL WHERE THE CSJ
JOINING CHANNEL COVERS
HOLES ON THE CHANNELS
YOU ARE CONNECTING
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS

VIEW OF ROOF COMPONENTS
NO. PAGE 7
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed Model: J15301FK
88A
43A
43A
43A
43A
81A
81A
88A
INSTRUCTIONS
AND VIDEOS

VIEW OF WALL COMPONENTS
Absco Economy Shed
Model: J15301FK
PAGE 8
30A
31A
31A
30A
30A
30A
30A
31A
31A
31A
53B
79C
89B
89A
81A
90C
91A
91A
B
34A
53D
55B
61C
55B
81F
81A
80A
INSTRUCTIONS
AND VIDEOS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1

PAGE 9
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snaptite assembly system locks most perimeter channels to all roof and wall
sheets without the need for tools and fasteners.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush with the
edges of the sheets.The snaptite system allows
adjustment for this process by simply tapping the
channel along the sheets until each end is neatly
flush. If you need to remove channels from the
panels, pull the channel along the panel from
opposing ends. You may need someone to help
with this.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
4mm NUT & BOLT SET
3mm POP RIVETS
PUSH
PUSH
HIGH SIDE
HIGH SIDE
PUSH
HIGH SIDE
HIGH SIDE
After joining sheets together, position channel over one end of the sheets, gently
tapping it over the snaptite lugs, working along the sheets to the other end.
HIGH SIDE
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Join components together by pre-drilling the holes
first. Use one component as a template to mark where
the holes are. Drill with 3mm drill bit.
D

1. REAR PANEL ASSEMBLY
PAGE 10
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
SNAP
T TE
i
SNAP
T TE
i
61C
81F
30A
30A

PAGE 11
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
2. SIDE PANEL ASSEMBLY
LEFT SIDE PANEL
SNAP
T TE
i
SNAP
T TE
i
31A
31A
31A
80A
55B
81A
30A
Reverse side of
Door Mullion

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
PAGE 12
RIGHT SIDE PANEL
SNAP
T TE
i
SNAP
T TE
i
3. SIDE PANEL ASSEMBLY
55B
81A
30A
31A
31A
30A

PAGE 13
4. ROOF PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
SNAP
T TE
i
SNAP
T TE
i
43A
43A
43A
81A 88A
81A
88A
43A

PAGE 14
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
SNAP
T TE
i
SNAP
T TE
i
34A
89A
53B
53D
79C
89B
90C
5. FRONT PANEL ASSEMBLY
90C
53A
53A
90C
89A
89A
53A
90C
89B
53A
90C
79C
53B 53B
90C
79C
79C
89B
89B
89A
89A
34A

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
6. DOOR PANEL ASSEMBLY
20mm FLANGE
58C
58C
58A
15mm FLANGE
B
B
SNAP
T TE
i
SNAP
T TE
i
58B
12A
ALL VERTICAL DOOR CHANNELS ARE INSTALLED IN THE REVERSE
DIRECTION IN COMPARISON TO HORIZONTAL DOOR CHANNELS
PAGE 15

PAGE 16
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for
proper alignment. position each hasp centrally over the padbolt shaft, and drill 3mm holes and secure with screws
NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED
INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY
ENLARGING THE HINGE HOLE SETS IN THE JAMB
USING A 4MM DRILL BIT
7. DOOR PANEL ASSEMBLY
91A
91A
B
B

PAGE 17
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
PANEL CONSTRUCTION
NOTE: Take care to ensure that both front
and rear wall panels are not positioned
upside down. The top channel of each
panel is pre-punched for attaching roof
sheets. The base channels are not
pre-punched.
SIDE WALL PANEL CHANNELS FIT
INTO THE NOTCHED FRONT AND
REAR WALL PANEL CHANNELS
31A
80A
89B
CONNECT DOOR MULLION
SECTIONS WITH SIX 20mm SCREWS
REPLACE PADBOLT HASP 10mm
SCREWS WITH 20MM SCREWS

PAGE 18
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J15301FK 08/05/17 V1.1
Absco Economy Shed
Model: J15301FK
INSTRUCTIONS
AND VIDEOS
FINAL CONSTRUCTION
DYNABOLT
BOLT & NUT
STEEL
ANGLE
SLAB
WALL
SHEET
- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,
DYNABOLT AND STEEL ANGLE
- DRILL A 10mm HOLE INTO THE WALL SHEET
- DRILL A 10mm HOLE INTO THE CONCRETE
ANCHORING OF SHED
LOCATION OF 12
CONCRETE ANCHORS