ABSCO SHEDS 1508WBCK User manual

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 1 15/09/2022
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
PLEASE LEAVE A REVIEW
Tell us about your experience!
Visit www.abscosheds.com.au/review
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
773 mm
1513 mm

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 2 15/09/2022
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
• Do not sit, stand or walk on the roof of your shed.
RECOMMENDED
5/16” Hex driver bit
Hammer drill Shifter
10mm metal drill bit
10mm masonry drill bit
Pop riveterTinsnipsCordless drill

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 3 15/09/2022
COMPONENTS LIST
QTY DESCRIPTION No. CHK QTY DESCRIPTION No. CHK
4
STEEL SHEET
STRAIGHT
1130 x 773 mm
44Z 1
STEEL SHEET
STRAIGHT
1070 x 773 mm
37B
1
STEEL SHEET
STRAIGHT
785 x 773 mm
43Q 1
STEEL SHEET
STRAIGHT
1070 x 711 mm
37C
1
STEEL SHEET
STRAIGHT
785 x 773 mm
43R
FITTINGS PACK
QTY DESCRIPTION No. CHK QTY DESCRIPTION No. CHK
6
64 mm
BUTT HINGE
6 HOLE
FAST
012A 16 mm
DRILL BIT
DRILL
2
2DOOR
PLATE 12A 1 HASP & STAPLE
FAST
052
6CHANNEL
JOINER CSJ 12 8G x 3/4” SELF TAPPING SCREW
FAST
013
1C HANDLE
32 mm
FAST
048 1
SBS43E POP
RIVET
x 50
PACK
12
2M4 X 10 mm
PAN HD SCREW
FAST
060 4
DOOR TRACK
BRACKET
150 x 150 x 20 mm
BKT
260
1DOUBLE DOOR
FITTINGS PACK
PSTK
DBL 3PADBOLT FAST 006
1
8G x 3/8” SELF
TAPPING SCREW
x 220
PACK
220 2PADBOLT
HASP
FAST
007
13 mm
DRILL BIT DRILL 1 PHILLIPS HD DRIVER BIT
FAST
038
8
3/16” ROUND HD
BOLTS &
NYLOCK NUTS
FAST
002
FAST
003
12 3/16” COUNTERSUNK
BOLTS & NUTS
FAST
004
FAST
005

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 4 15/09/2022
CHANNEL PACK

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 5 15/09/2022
Guide on Joining Spliced Channels
The text marked on all parts must be shown on the same side as each other
Step 1.
Position the channels and the
CSJ joiner so the centre of
the CSJ is in line with the end
of each channel to be joiner
together.
Step 2.
Join the first channel to the CSJ
by inserting the centre of the
CSJ, on an angle, to the end of
the channel where the JOIN>>
text is marked.
Push down one side of the CSJ
until you hear a ‘click’.
Step 3.
Join the second channel to the
CSJ by positioning the <<JOIN
of the channel at the centre of
the CSJ, on an angle. Push the
CSJ into the channel until you
hear a ‘click’.
Finished Channel.
The joined channels should
now look like the picture with
the CSJ positioned equally
inside of the joined channels.
Drill out holes with 3mm drill
bit in CSJ to match the holes
in channel. Drilling of screws
on the joined channels is being
done after sheets are locked on
the spliced channels.
= =
JOIN>> <<JOIN
CSJ
==
JOIN>>
J
==
JOIN>> SJ
= =
JOIN>>
<<JOIN
= =
JOIN>> <<JOIN
Finished Spliced
Channel
Channel
Push
20mm 15mm
CSJ
.
...

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 6 15/09/2022

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 7 15/09/2022
PANEL OVERVIEW
Detail to follow
81J
61G
61G
44Z
44Z
44Z
37C
53J
53H
79H
91K
91K
81F
91H
44Z
37B
80F
80F

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 8 15/09/2022
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 9 15/09/2022
REAR PANEL ASSEMBLY

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 10 15/09/2022
LEFT PANEL RIGHT PANELSIDE PANEL ASSEMBLY

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 11 15/09/2022
LID PANEL ASSEMBLY

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 12 15/09/2022
DOOR PANELS ASSEMBLY

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 13 15/09/2022
DOOR PANELS ASSEMBLY
Flip both panels over

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 14 15/09/2022
FRONT PANEL ASSEMBLY

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 15 15/09/2022
DOOR PANEL INSTALLATION
NOTE: NUTS AND BOLTS
(SUPPLIED) MAY BE USED
INSTEAD OF POP RIVETS
(SUPPLIED) BY SIMPLY
ENLARGING THE HINGE
HOLE SETS IN THE JAMB
USING A 4MM DRILL BIT
FAST009
FAST009
FAST009
FAST009
37B
37C

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 16 15/09/2022
SIDE WALL PANEL CHANNELS FIT
INTO THE NOTCHED FRONT AND
REAR WALL PANEL CHANNELS
44Z
80F
91K
CONNECT DOOR MULLION SECTIONS WITH SIX
FAST013 SCREWS ON EACH SIDE
FAST001
FAST001
FAST001
FAST001
FAST013
(REFIT)
FAST013
FAST013
FAST013
FAST013
FAST013
(REFIT)
FAST009
FAST009
FAST009
FAST009
WALL PANEL ASSEMBLY
FIT 4x BKT260 BRACKETS TO TOP INSIDE
CORNERS USING FAST001 SCREWS.
PREDRILL FOUR 6mm HOLES IN BRACKET
FIRST WITH SUPPLIED DRILL BIT.

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 17 15/09/2022
LID PANEL INSTALLATION
NOTE: The two holes required to connect the
padbolt hasp for each door have not been
pre-punched, to allow for proper alignment.
position each hasp centrally over the padbolt
shaft, and drill 3mm holes and secure with screws
FAST009
FAST009
FAST009

Absco Industries Assembly Instruction Manual
ABSCO BIN COVER
MODEL: 1508WBCK
1.52m W x 0.78m D x 1.15m H
Model: 1508WBCK 2.1 18 15/09/2022
FINAL CONSTRUCTION
LOCATION OF 4
CONCRETE
ANCHORS
FAST052
HASP
FAST052
LATCH
TIP: TIE A STRAP OR CORD THROUGH THE FAST062 SADDLE
ONTO YOUR WHEELIE BIN HANDLES TO CREATE A ONE-LIFT
LID OPENING FEATURE
DYNABOLT
BOLT & NUT
STEEL
ANGLE
SLAB
WALL
SHEET
INSIDE VIEW
ATTACH HASP TO BOTTOM CHANNEL TO KEEP
DOOR.
NOTE: IF RAMP ACCESSORY IS BEING USED DO
NOT FIT THIS HASP.
INSTEAD DRILL A 10mm HOLE WHERE THE BOLT
STRIKES THE RAMP.
• EACH ANCHOR CONSISTS ON ONE NUT, BOLT,
DYNABOLT AND STEEL ANGLE
• DRILL A 10mm HOLE INTO THE WALL SHEET.
• DRILL A 10mm HOLE INTO THE CONCRETE SLAB
• POSITION THE STEEL ANGLE
• PLACE THE DYNABOLT INTO THE CONCRETE
HOLE & TIGHTEN
• SECURE THE STEEL ANGLE TO THE WALL SHEET
USING THE NUT & BOLT
• REPEAT FOR EACH ANCHOR LOCATION

Lifetime Warranty Statement
This warranty against defects is given by:
Absco Industries (ABN: 77 869 708 678)
Address: PO Box 119 Acacia Ridge QLD 4110
Ph: 1800 029 701
Fax: [phone]
Email: [e-mail]
Date of issue: 19 December 2018
Details of Manufacturer’s Warranty
This product comes with a Lifetime structural warranty from the date of purchase. This warranty also
applies where there are missing or damaged parts identied in the parts list referred to in the instruction
kit within the product packaging.
Please ensure that you keep this warranty form in a safe place along with your proof of purchase. You can
register your warranty online http://abscosheds.com.au/warranty-details/ or complete the form on the
back of this document and mail it back to Absco, along with a copy of your proof of purchase.
The benets of this warranty are in addition to your rights under the Australian Consumer Law (ACL) and
in particular, the guarantees implied under the ACL and any other rights and remedies of the consumer
under a similar law in relation to the goods and services to which this warranty relates.
Process of claiming warranty:
To make a claim under the warranty within the warranty period, you will need to contact the manufacturer
directly by phone or email:
Contact Number: 1800 029 701
Contact Email: [e-mail]
You will be required to produce proof of purchase (this is at discretion of the manufacturer) at the time of
the claim.
The manufacturer bears the cost of replacing the products or spare parts or repairing the products and
reasonable direct expenses of claiming under this warranty:
Where parts are replaced, the manufacturer will bear the cost of sending the spare part and will endeavour
to deliver it to the customer’s nearest reseller within 20 working days for the customer to pick up. At such
time the customer may be required to return the alleged faulty parts.
Where assessment is required in case of replacing or repairing the product, the manufacturer will appoint
an assessor within 10 working days to identify the alleged defect. The manufacturer will bear the repair
costs by appointing a local tradesman. The manufacturer may choose to replace the product if the repair or
the cost of repair is not feasible. The replacement product will be available for collection from the nearest
reseller within 20 working days. The customer will bear the cost of assembly for the replacement product.
1

IMPORTANT
1. Manufacturer’s Disclosure
This warranty against defects shall not apply in the following situations:
A)Where the product is not assembled in accordance with the instructions provided in the product kit;
B)Where the product is used to store corrosive materials such as fertilizer, chlorine etc;
C)The warranty does NOT cover damage caused by storms, wind, rain, snow or poor foundations;
D)This warranty does not apply to surface deterioration of panels caused by ‘Swarf’ (Tiny particles of
steel debris left from cutting, grinding or drilling operations) that has not been removed after building
construction.
2. Notes
This product is weatherproof to a certain level; however driving windy rain may cause the product to leak.
Condensation may also occur in some weather conditions such as extreme heat or cold. The product
should only be used for storing items such as gardening equipment and should not be used for articles
that may be prone to damage if they come into contact with moisture.
3. Major Defects
If the manufacturer is satised that the defect is a major defect, the purchase price may be refunded in lieu
of providing a replacement product or repairing the product.
This warranty is provided in addition to other rights and remedies you have under law: Our goods come
with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to
replacement or refund for a major failure and to compensation for other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
If you do not wish to register your warranty online, complete the below form and email, fax or
post this form back to Absco, along with a copy of your proof of purchase.
NAME:
STREET ADDRESS: POSTAL / ZIP CODE:
STATE / CITY / PROVINCE / REGION:
COUNTRY:
SHED TYPE/CODE:
ORDER NO:
DATE OF PURCHASE:
EMAIL ADDRESS:
DATE REGISTERED:
2