Abt G100-24L User manual

CAUTION
1. SAVE THIS INSTRUCTIONS- This manual contains important safety and
operating instructions for the G100-XXL battery charger.
Please read the caution ofbatteries or devices you want to charge firstly!
2. When charging, batteries can emit explosive gases, therefore it is essential to
prevent flames and sparks. The charger is designed for charging specified
Li-Ion/LiFePo4 batteries. Do not use for any other purpose.
3. Always provide good ventilation when charging.
4. Use of an attachment not recommended or sold by Green-Digital Power-tech
may result in a risk of fire, electric shock or serious injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by the plug rather than
by the cord when disconnecting charger.
6. An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure that: a) Pins on plug of extension
cord are the same number, size and shape as those of plug on charger; b)
Extension cord is properly wired and in good electrical condition; and c) Wire
size is large enough for ac ampere rating as specified in “technical data”.
7. Do not operate charger with a damaged cord or plug-return the charger to the
place where purchased.
8. Never operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way; take is to a qualified serviceman.
9. Do not disassemble the charger; take it to a qualified serviceman when
service or repair is required. Incorrect reassembly may result in a risk of
electrical shock or fire.
10. To reduce risk of electric shock, unplug charger from AC outlet before
attempting any maintenance or cleaning. Turning off controls will not reduce
the risk.
G100-XXL 12.8V～38.4V (4s~12s)
Li-Ion/Polymer/LiFePo4 Battery Charger
User’s Manual
May, 2011 Version 1st
Brief Introduction

G100-XXL is a main member of digital-chargers from
. It represents today’s new technology for 12.8V(4s) ~
34.8V(12s) Li-Ion/Polymer/FePo4 battery pack charging. G100-XXL
programmed 3 auto stages ( Ip-Im-Um) charging process，It is designed for
3~25Ah Li-Ion/Polymer/LiFePo4 battery pack. Stage “Ip” is a pre-charge
function for deep discharged battery pack, this is helpful for battery’s cycle life.
When the battery recovered by pre-charge small current, stage “Im” will give
bulk current charging. Then, “Um” stage is followed, the output voltage is
limited on 14.4V(for 4S LiFePo4) or 16.8V(for 4S Li-ion/polymer), until the
charge current declined to 0.4A. At this stage, the battery is charged
completely and the charger will cut off output automatic.
Further, G100-XXL can display the charging process, indicate the battery
capacity from 25% to 100% timely. This is helpful for user.
For more safety, G100-XXL will inter protection mode when the battery
polarity reversed our the output connectors shorted.
Specification for G100-XXL
Input Voltage 100-240VAC，50-60Hz
Input Current 1.6A
Back current drain 1）<1mA
G100-12LF G100-24L G100-36L G100-36LFCharge voltage limit
14.4V+-1% 29.4V+-1% 42V+-1% 43.2V+-1%
Bulk charge current 4.5A+-5% 2.8A+-5% 1.8A+-5%
Operate Temperature -20℃~50℃
Cooling Natural convection. Do not cover the charger.
Charge principle Auto 3 stages: Ip-Im-Um
Cut-off when charge finished.
Battery type F
rom 12.8V(4s) to 38.4
V
(12s),
Li-
ion/Polymer/
LiFePo4
Battery capacity 3-25Ah
Size 170X70X51mm
Enclosure IP54 (
Dust
protected
,
Wat
er splashing
resistance)
Weight 400g
Display Panel
How to use:
1. Connect theAC cord tothe socket, The “power” lamp will light on solid.
2. Connect positive charger clip (red) to positive battery terminal, the black clip
to negative. (You can use other dc plugs to connect battery), the
“25%~100%” lamps will light on flowing. If the battery polarity reversed or
output shorted, “Warning” lamp will flashing, please check the setup.
3. Depend on the charged capacity, 25%~100% lamps will lights up solid
sequence, until the battery is fully charged. Then you can power off the
charger and disconnect the battery or you can charge a new battery if you
need.
The table shows the durationof 80% state charged for anempty battery.
Battery cap. G100-12LF G100-24L G100-36L
3.2Ah Not recommend 1.5 hours 2 hours
7.0Ah 2 hours 3 hours 4 hours
12Ah 3 hours 5 hours 7 hours
25Ah 6 hours 10 hours 13 hours
Charging process indicator:
Indicate battery capacity from 25% to 100% when
charging.
All lamps flashing means battery polarity reversed or
output shorted.
All lamps are “off” means no battery.
Power on
(When AC
input OK)
Shenzhen ABT
Electronics CO.,LTD