Acclaim Lighting AL-Dimmer-1 PRO User manual

RS
ON
109876
5
4
3
21
6A Max.
GND
Data -
Data+
GND
Data -
Data+
+12-24V
GND
DC IN
Made in P.R.C.
DMX ADDRESS SETTING
DMX IN
DMX OUT
AL-DIMMER-1 PRO
1
1
2
2
4
4
8
8
16
16
32
32
64
64
128
128
256
Dim
Addr
Load (6A)max
Analog
GND
+12-24V
+12-24V
GND
GND
0-10V IN
On
Off
DESCRIPTIONS
24-004-2461-00
Rev 1.1
Congratulations with your purchase of this product.
Check for transport damage.
You should be in possession of the following items:
1 AL-Dimmer-1 PRO
1 Manual, 1 Screwdriver & 1 Connecting part
Should you discover transport damage after unpacking the
equipment, inform the hauler immediately. Never connect a
damaged device. You may also contact your supplier.
DELIVERY PACKET
TECHNICAL SPECIFICATIONS
Operation temperature
Housing
Control Protocol
Listing
Dimensions
Weights
0 degC to + 40 degC
Black plastic
DMX-512 (1990)
CE certified
50g
Power Requirement 12~24VDC 6A Max
*Please Note: Improvements and specifications in the design of the unit and the manual are subject to
change without any prior written notice.
OPERATION GUIDE
1.DMX Control Mode(DMX Addressing)
DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication between
intelligent fixtures. Each Dip Switch represents a binary value.
In this mode, the dip-switch 10 is flipped to the " " position, DMX address can
be addressed and the intensity of LED product is dimmable.
ON 12345678910
ON
OFF
1=
0=
Connection Terminal
Read this manual carefully before using our AcclaimLighting AL-Dimmer-1 PRO. This unit serves as a single channel
dimmer. A maximum of up to 6A loads are allowed on a single output, DMX address enables to be addressed by
flipping the dip-switch. The dimmer is available in DMX Control Mode, Manual Dim Mode and features 0-10V analog
input. The intensity of LED product can be dimmed in the Manual Dim Mode.
AL-Dimmer-1 PRO
Input 2-pin terminal connector for Power In
2-pin terminal connector for Analog In
3-pin terminal connector for DMX In
Output(6A Max.) 3-pin terminal connector for DMX out
4-pin terminal connector for LOAD
90(L) x 40(W) x 20(H)mm
User Instructions
AL-Dimmer-1 PRO
-Page 1-
INGRESS PROTECTION RATING IP20

2.Manual Control Mode
In this mode, the dip-switch 10 is flipped to the " " position,
Flip the dip-switch 1~8 to set the intensity of LED product.
Each Dip Switch represents a binary value.
OFF
12345678910
ON
OFF
1=
0=
The intensity is set by combining the different dipswitches that will add up to the value you wish to achieve,
for example: Setting the Intensity for 21.
Flip switches1,3,&5 to the
"ON" position
Setting the Intensity for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
SWITCHES ON SWITCHES ON
Intensity
Value
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
..
..
..
..
..
1234 56 78910
ON
OFF
1=
0=
255 1,2,3,4,5,6,7,8
Intensity
Value
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve,
for example: Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
SWITCHES ON SWITCHES ON
START
CH#
START
CH#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
..
..
..
..
..
1234 56 78910
ON
OFF
1=
0=
511 1,2,3,4,5,6,7,8,9
..
..
-Page 2-

AL-DIMMER-1 PRO AL-DIMMER-1 PRO AL-DIMMER-1 PRO AL-DIMMER-1 PRO AL-DIMMER-1 PRO
TECHNICAL DRAWING(Connecting the X-CHIP LED PCB modules to the AL-Dimmer-1 PRO)
Analog
0-10V IN
Analog
0-10V IN
Analog
0-10V IN
Analog
0-10V IN
Analog
0-10V IN
-Page 3-