Acclaim Lighting Flood One EO Series User manual

www.acclaimlighting.com Flood One EO
User guide

1
www.acclaimlighting.com
CONTENTS
INTRODUCTION ....................................... 2
Welcome 2
Safety, maintenance and cleaning 2
Supplied items 3
Optional accessories 4
INSTALLATION.......................................... 5
Tilt adjustment 5
Using a tenon mount 6
Using a pipe clamp 7
Power and control wiring 8
Input wiring protection 8
Optional DMX operation 9
Optional wireless DMX operation 9
Optional wireless 0-10V operation 10
FURTHER INFORMATION............................ 11
Troubleshooting 11
Specifications 12
Dimensions 13
Limited product warranty 16

2www.acclaimlighting.com
INTRODUCTION
WELCOME
Welcome to the Flood One EO range from Acclaim Lighting, a small family of aluminum
bodied IP66-rated exterior LED flood fixtures.
The Flood One EO family fully embraces
Acclaim Lighting’s Modular Systems
(AMS) design standard; AMS allows
a wider choice of internal and external options to be configured in our Los Angeles
headquarters and delivered in industry-leading time. There are numerous emitter options,
together with a native beam angle of 10O, adjustable using a range of spread lens options to
suit your installation:
•2700K, 3000K, 3500K or 4000K (all with Color Rendering Indexes of more than 80),
•10º standard with 20º, 40º, 60º, 90º x 60º or 10º x 60º optional spread lenses.
Additionally, factory fitted half and full snoots allow the light output to be shaped further.
Control is achieved using the industry standard 0-10V sink format and, with the addition of
the optional Acclaim Lighting ZDM 6 and Aria units (see page 9), you can add remote
wireless connectivity to the list of abilities within the Flood One EO range.
The internal auto-sensing power supply within each unit can accept mains inputs between
100 to 277VAC at 50 or 60Hz. Total power consumption is just 60W peak, 55W steady state.
SAFETY
•When fixtures are mounted off-ground, ensure they are securely fitted to an appropriate
mounting surface.
•Ensure that the power input is supplied from a correctly fused, earthed and
environmentally protected location.
MAINTENANCE
CAUTION: Always isolate mains power before starting maintenance operations.
•Ensure that all mounting (and device) screws/bolts are fully tight and free of corrosion.
•Ensure there is no deformation to the housing, lenses or fixing points.
•Check that all power supply cables are free from physical damage or material fatigue.
•Use only genuine spare parts supplied by Acclaim Lighting.
CLEANING
•Use a moist, lint-free cloth when cleaning each fixture.
•Never use alcohol or solvents.

3
www.acclaimlighting.com
SUPPLIED ITEMS
Standard model
Half snoot model
standard model plus [FBHSG]
Full snoot model
standard model plus [FBFSG]

4www.acclaimlighting.com
OPTIONAL ACCESSORIES
Tenon mounts
2” pipe (2.51”, 56mm inner dia.) [TM2]
4” pipe (4.13”, 105mm inner dia.) [TM4]
Pipe clamps (each can mount 1 or 2 fixtures)
2” pipe (2.51”, 56mm inner dia.) [PC2]
4” pipe (4.13”, 105mm inner dia.) [PC4]

5
www.acclaimlighting.com
INSTALLATION
When installing each Flood One EO fixture, ensure that the surface is level and that nothing
is protruding to damage the mounting yoke. Suitable mounting surfaces include steel,
aluminum, concrete or wood structures.
Each Flood One EO fixture is fitted with a swivel yoke mount, which has a center hole of
0.47” (12mm) and also two lock-off slots spaced at 6.3” (160mm) around the center line (see
page 13). The yoke has a thickness of 0.24” (6mm). Select bolts or screws (not supplied)
that fit the yoke holes correctly and are particularly suited to the mounting surface. Optional
tenon mounts and pipe clamps are available for mounting the fixture onto the top or sides
of poles respectively (see page 4).
TILT ADJUSTMENT
The yoke allows a tilt range of more than 180 degrees to be achieved. Use a 3/8” (10mm)
Allen wrench to adjust the tilt angle. A useful tilt gauge is provided at each end of the
fixture:
80
60
40
20
0
20
40
60
80
80
60
40
20
0
20
40
60
80
Read o the tilt
angle here

6www.acclaimlighting.com
USING A TENON MOUNT
Optional tenon mounts are available for use when a Flood One EO needs to
be mounted on top of a vertical pole. Tenon mounts are available for use
with 2” (50mm) and 4” (100mm) poles of sufficient rigidity for the weight of
the fixture.
IMPORTANT: Tenon mounts are suitable
only for vertical pole mounting
where the xture sits on top of
the pole. Tenon mounts must
NEVER be used to hang a Flood
One EO below a pole.
TO USE A TENON MOUNT
1 Slide the tenon mount onto the
vertical pole and secure using the two
bolts on the side (1/4” /6mm Allen (hex)
wrench required).
2 Fix the Flood One EO to the tenon mount using
the supplied main bolt (17mm A/F wrench
required) as shown right.
3 Where required, feed the mains/
control cable into one of the two
access holes and down the pole to
a suitable exit point.
4 Use a suitable silicone sealant to
cap off the cable access holes to
prevent water ingress.
Main
bolt
Pole
bolts

7
www.acclaimlighting.com
USING A PIPE CLAMP
Optional pipe clamps are available to mount Flood One EO fixtures on either 2”(50mm) or 4”
(100mm) tubes and poles.
IMPORTANT: Ensure the pipe and its mountings have sucient load capacity for the
Flood One EO xture(s) to be mounted.
TO USE A PIPE CLAMP
1 Separate the two halves of the
clamp, if they are already bolted
together.
2 Place the two halves of the
clamp around the pipe.
3 Use the two longer
bolts, one from each
side to join the two
halves - see below
about the correct
use of the supplied
washers.
4 Tighten the two main
bolts evenly until the
clamp is held firmly in
place.
5 Use one of the two
smaller bolts (with
spring and standard
washers) to fix the Flood
One EO yoke to one side of the
clamp and tighten.
(2 o)
M10 x 50mm
Using the supplied washers
The supplied spring washers
help to maintain tension on the
bolts to prevent loosening.
Always place the spring
washer on each bolt
first and then add
the standard washer,
before inserting the
bolt into the clamp.
This will prevent the
steel spring washer
from denting the softer
aluminum body of the
clamp.
(1 o)
M10 x 25mm

8www.acclaimlighting.com
Blue:
Neutral
Brown: Live
Green/yellow: Ear
th
POWER AND CONTROL WIRING
Power and control are arranged as separate bare-tail inputs via cords that are each 6.5’(2m)
in length.
POWER
The power feed is as follows. The fixture must have a valid ground connection:
•Voltage: 100-277VAC 50/60Hz
•Power: 60W
•Feed cable: 16 AWG / 1.31mm2
Note: Acclaim recommends taking proper precautions for external surge protection, as control
and power electronics can be damaged by major events.
CONTROL
The control cable has two cores for the 0-10V input:
INPUT WIRING PROTECTION
Ensure that appropriate care is taken to protect the junction where the mains and control
inputs are joined to the fixture’s feed cables.
Ensure that:
•the mains input is derived from a suitable overload-protected supply.
•the junction boxes have an environmental rating of at least IP66.
•all cable access points, plus the enclosure cover are correctly sealed and moisture proof.
•only suitable cable connectors are used within the junction boxes; Acclaim Lighting
recommends Wago® 221-series splicing connectors.
•local codes are followed during planning and installation. Some municipalities have
specific requirements when wiring low and high voltage cables in close proximity. Such
requirements could include the use of a barrier within combined junction boxes (if used)
or particular minimum spacings between the control and power cables.
•connections are made, inspected and certified by a qualified electrician.
White: 0-10V +
Black: 0-10V -
•Feed cable: 18 AWG / 0.824mm2