ACD GRUPPE M210SE Reference guide

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 1 / 32
Brief Overview/
Resumen breve
M210SE Set (M210SE/DS210)
U.S. Edition 201
6
/
EE. UU.
Edición 201
6
Version: 1.04
© 2015 ACD Group
All Rights Reserved/Todos los derechos reservados
This document may not be duplicated or made accessible to
third parties without written permission by ACD.
Este documento no se puede reproducir ni facilitar a
terceros sin consentimiento por escrito de ACD.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 2 / 32
Table of Contents/Índice
1
Scope of Delivery.........................................................................................3
2
Intended Use................................................................................................4
3
Handling.......................................................................................................5
3.1
Prior to the initial Commissioning of the M210SE.....................................................5
3.2
Handling of the Device and Docking Station ............................................................7
3.2.1
Charging the Power Supply Unit for the DS210 & M210SE................................8
3.2.2
Inserting the Battery into the M210SE Handheld Terminal .................................8
3.2.3
Inserting the M210SE into the DS210 .................................................................9
3.2.4
Switching on the M210SE Handheld Terminal....................................................9
3.2.5
Suspend Mode...................................................................................................10
3.2.6
Switching off the M210SE Handheld Terminal..................................................10
3.2.7
Status of the DS210 Docking Station LEDs.......................................................11
4
Cleaning and Maintenance Information......................................................12
4.1
Display ....................................................................................................................12
4.2
Charging and Communication Contacts.................................................................12
4.3
Scanner, Camera and Camera light window..........................................................12
5
Service and Spare Parts ............................................................................13
6
FCC Statement of Compliance...................................................................14
7
Manufacturer’s Representations and Warranties.......................................15
8
Volumen de suministro...............................................................................17
9
Uso previsto ...............................................................................................18
10
Manipulación..............................................................................................19
10.1
Antes de la primera puesta en funcionamiento del M210SE..................................19
10.2
Manipulación del dispositivo y de la estación de carga..........................................21
10.2.1
Carga de la unidad de alimentación de la DS210 y del M210SE......................22
10.2.2
Inserción de la batería en el terminal de mano M210SE...................................22
10.2.3
Inserción del M210SE en la DS210...................................................................23
10.2.4
Encendido del terminal de mano M210SE ........................................................23
10.2.5
Modo de suspensión..........................................................................................24
10.2.6
Apagado del terminal de mano M210SE...........................................................24
10.2.7
Estado de los LED de la estación de carga DS210...........................................25
11
Información de limpieza y mantenimiento..................................................26
11.1
Pantalla...................................................................................................................26
11.2
Contactos de carga y comunicación.......................................................................26
11.3
Lector, cámara y ventana de luz de la cámara.......................................................26
12
Asistencia técnica y piezas de repuesto.....................................................27
13
Declaración de conformidad FCC..............................................................28
14
Declaraciones y garantías del fabricante ...................................................29

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 3 / 32
1 Scope of Delivery
The package contains the following items:
1 Device incl. battery
2 Replacement battery (optional)
3 Docking station (optional)
4 Connection kit for docking station – two parts (optional)
5 Brief overview M210SE Set, M210SE/DS210 (quick start manual)
Check package for completion and possible damages.
Figure 1: Package content
ATTENTION
The M210SE battery is a lithium ion battery pack. Lithium ion
battery packs can explode if exposed to fire. Do not disassemble
the battery pack and do not expose it to fire or heat (greater than
140 °F).
ATTENTION
Never position the device in close proximity to heat sources
(heating fans or similar equipment) and never expose it to direct
sunlight, excessice dust sources or shocks.
ATTENTION
The touch pen may only be used for operation of the touch screen.
It should not be used for any other purposes.
1
2
3
4
4
5

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 4 / 32
2 Intended Use
The M210SE Set (M210SE/DS210) data acquisition system is a solution for the mobile acquisition and
transfer of data. Do not use the system in geographical areas where explosives may be used.
Observe all warning information regarding the use of wireless devices.
The supplied connection kit (see Point 1) is only intended for use with the M210SE Set.
NOTE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment This
equipment generates, uses, and can emit radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
interference with certain radio communications
NOTE
This device complies with Part 15 of the FCC Rules Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 5 / 32
3 Handling
Read all instructions first before using the M210SE!
Do not drink any alcohol or take any drugs while using the M210SE
and follow the saftey instructions carefully!
3.1 Prior to the initial Commissioning of the M210SE
In order to ensure that the battery inserted into the device at the factory is fully charged, insert the device into
the supplied DS210 docking station (if included in the scope of delivery), also see Section 3.2. Using the
supplied power supply unit, connect the docking station to the mains (Power LED shows a green light), also
see Section 3.2.
The battery charging process has been completed when the 'CHARGE' LED is green.
You can now use the M210SE handheld terminal.
You can see the battery charging process in Figure 2.
ATTENTION
Only original ACD power supply units and ACD-approved batteries
may be used for the operation of the M210SE and the DS210. The
utilization of non-approved components can lead to the
destruction of the device. Remove the battery from the device if it
is not used for an extended period of time.
ATTENTION
The M210SE battery is a lithium ion battery pack. Lithium ion
battery packs can explode if exposed to fire. Do not disassemble
the battery pack and do not expose it to fire or heat (greater than
140 °F).
ATTENTION
Prior to each use, the mobile data acquisition terminal, the docking
station and the connection cables must be inspected for damages.
Damaged parts must be replaced. Please contact ACD in either
case.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 6 / 32
1 2 3
4 5 6
Figure 2: Charging Process
1: 1. Green LED: Docking station has power
2. Red LED: The battery in the device is charging.
2: 1. Green LED: Docking station has power
2. Green LED: The battery in the device is fully charged.
3: 1. Green LED: Docking station has power
2. Green LED: The battery in the device is fully charged.
3. Red LED: The second battery is charging.
4: 1. Green LED: Docking station has power
2. Green LED: The battery in the device is fully charged.
3. Green LED: The second battery is fully charged.
5: 1. Green LED: Docking station has power
3. Red LED: The second battery is charging.
6: 1. Green LED: Docking station has power
3. Green LED: The second battery is fully charged.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 7 / 32
3.2 Handling of the Device and Docking Station
Read all instructions first before using the M210SE!
Do not drink any alcohol or take any drugs while using the M210SE
and follow the saftey instructions carefully!
ATTENTION
Laser Radiation: Do not stare into the beam.
The laser classification is stated upon one of the stickers on the device.
ATTENTION
Only operate the touchscreen using the fingertips or with the
touch-pen attached to the retainer strap on the rear. Never use a
pen or other sharp objects.
ATTENTION
Never position the device in close proximity to heat sources
(heating fans or similar equipment) and never expose it to direct
sunlight, excessive dust sources or shocks.
ATTENTION
In order to prevent excessive heat, the terminal, as well as the
docking station and the power pack must not be covered while in
use.
ATTENTION
Make sure there is no risk of stumbling over connection cables or
power packs.
Laser beam exit

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 8 / 32
3.2.1 Charging the Power Supply Unit for the DS210 & M210SE
The M210SE and the spare battery may only be charged in the DS210 docking station with the respective
power supply unit.
•External power supply unit for DS210
•Input voltage
~
100 – 240 V AC; 0.8 A; 50 – 60 Hz
•Output voltage 15 V DC; 2.4 A
•Power cable (country-specific)
ATTENTION
Unintended use of the interfaces should be avoided.
3.2.2 Inserting the Battery into the M210SE Handheld Terminal
The battery compartment is located at the rear end of the device. In order to open the cover, first remove the
transverse hand strap by unhooking it. Now push the locking tab on the battery compartment cover towards
the cover surface. The compartment then opens.
The battery can be inserted without the use of force. The long groove on the unlabelled side of the
battery is the top side. The opening of the groove faces the recess for the opening mechanism. In doing so,
ensure that you insert the battery at a slight incline towards the contacts and then bring it into its final
position while applying a slight amount of pressure. You can see how to insert the battery in Figure 3. First,
place the cover on the three securing straps and then push into the locking mechanism.
Figure 3: Inserting the Battery

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 9 / 32
3.2.3 Inserting the M210SE into the DS210
Figure 4: Inserting the M210SE into the DS210
ATTENTION
Place the docking station correctly on a smooth and clean
underground, which is not exposed to direct sunlight.
3.2.4 Switching on the M210SE Handheld Terminal
In order to switch on the device, press the “C” button and the “F” button” until the LED beneath it lights up.
Then you can release the buttons. The desktop of your operating system or your usual work environment
appears. You can see the buttons, you have to press to switch on the device as shown in Figure 5.
Figure 5: Switching on the M210SE

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 10 / 32
3.2.5 Suspend Mode
In suspend mode, the operating system and the application running on it are stopped. The display is
switched off and consequently becomes dark. Suspend mode can be accessed by pressing the “C” button
an the “F” button, whereby the “C” button must first be pressed and held. Then the “F” button must also be
pressed. Upon leaving suspend mode (switching on the M210SE), the application and the operating system
starts to run from the same point. Thanks to both measures, the M210SE only uses a small amount of
power.
Figure 6: Suspend Mode of the M210SE
3.2.6 Switching off the M210SE Handheld Terminal
The device can be switched off by pressing the “C” button, the top right button and the “F” button whereby
the “C” button must be pressed and held first. Then additionally press the top right button and hold it. Then
additionally press and hold the “F” button (see Figure 7). Hold these three buttons for a minimum of 10
seconds!
Figure 7: Switching off the M210SE

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 11 / 32
3.2.7 Status of the DS210 Docking Station LEDs
The DS210 status LEDs are located on the front of the docking station.
Figure 8: Status of the DS210 LEDs
The POWER LED shows a green light as soon as the DS210 is supplied with current via the power supply
unit.
The CHARGE LED shows a red light when the M210 is charging. The LED shows a green light once the
M210SE is fully charged. In order to ensure a correct display, the M210SE must be switched off. If the
M210SE is switched on, the CHARGE LED may show a red light although the battery is already charged.
The 2. BATTERY LED shows a red light if a spare battery is being charged. The LED shows a green light
once the spare battery is fully charged.
With the DS210 Ethernet, the CONNECT LED flashes green if the DS210 is connected to the LAN (Ethernet)
with a network cable and the M210SE has loaded the Ethernet driver. Therefore, the CONNECT-LED has
the same function as the green Link LED on the network socket (RJ45 with two integrated LEDs) on the rear
end of the device. The yellow LED is the Tx LED. It flashes if data is being transmitted from the M210SE into
the LAN via the DS210.
Figure 9: RJ45 connector with LEDs
ATTENTION
Unintended use of the interfaces should be avoided.
Link LEDTx LED
Power
Supply

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 12 / 32
4 Cleaning and Maintenance Information
Turn off the device before starting any cleaning or maintenance
process!
Make sure that the laser beam is switched off by checking the
laser beam exit!
ATTENTION
Do not use any corrosive chemicals, cleaning solutions or strong
cleaning agents in order to clean the device.
ATTENTION
All components must be disposed of properly at the end of their
technical lifetime.
Clean the device when dirty and by placing it firmly onto a surface (e.g. table). This ensures a secure hold
and the device cannot slip out of your hand during the cleaning process.
4.1 Display
Clean the display with a soft, dry cloth. In order to do, always switch off the device as the display responds to
all contact and could therefore compromise or interfere with the active program. Do not apply any severe
pressure on the display.
4.2 Charging and Communication Contacts
If transfer problems occur, clean the charging and communication contacts with a soft, moist cloth.
When dealing with the DS210, the power plug must be disconnected beforehand.
4.3 Scanner, Camera and Camera light window
In the event of any irregularities during scanning, switch off the device and clean the scanner window with a
soft, dry cloth. The scanner window is ultra-transparent and can hardly be seen with the naked eye. Carefully
clean the window without applying excess force on the glass.
Laser beam exit

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 13 / 32
5 Service and Spare Parts
If you have service requests please contact:
Hegele Logistic, LLC
855 N. Wood Dale Rd., Suite A
Wood Dale, IL 60191
United States
Telephone: +1 847 690 0430
Fax: +1 630 354 6840
Email: repaircenter@hegelelogistic.com
If you require spare parts please contact:
ACD Elektronik GmbH
Engelberg 2
88480 Achstetten
Germany
Telephone: +49 7392 708 499
Fax: +49 7392 708 490
Email: info@acd-elektronik.de
Use Original Spare Parts Only.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 14 / 32
6 FCC Statement of Compliance

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 15 / 32
7 Manufacturer’s Representations and Warranties
ACD Elektronik GmbH
Engelberg 2
88480 Achstetten
Germany
Phone: +49 7392 708-0
Fax: +49 7392 708-190
These Representations and Warranties are applicable to all customers (the “Customers” and each,
individually, a “Customer”) purchasing products (the “Products”) manufactured by ACD Elektronik GmbH (the
“Company”).
1. Warranty and Limitations:
1.1. Company warrants solely to the original purchaser of the Products that for the Warranty Period (as
defined below), the Products will be free from defects in materials and workmanship under normal use, and
will conform to Company’s published specifications of the Products. Notwithstanding the foregoing, Company
retains its right to deviate from its published specifications due to the latest innovations and improvements in
function and design of the Products.
1.2. The foregoing warranty is subject to the proper storage, transportation and use of the Products, and
does not include defects due to normal wear and tear or deterioration.
1.3. Customer shall immediately, but in any event no later than eight (8) days following delivery or
installation of the Product, inspect the Products for conformity and visible defects. Customer shall give
Company immediate written notice of any non-conformities or visible defects regarding the Products. In the
event that Customer fails to provide the Company within eight (8) days following delivery or installation of the
Products with notice of any non-conformities or visible defects, any warranty claims in this regard shall be
deemed waived.
1.4. Customer shall immediately notify Company in writing of any other defects of the Products and
return such defective Product. Company’s sole obligation under the foregoing warranty is, at Company’s
option, to replace or exchange the defective Product or issue a merchandise credit for the defective Product.
Any replaced or exchanged Products shall be subject to the warranty set forth in 1.1., following their
replacement or exchange. If Company has received notification from Customer, and no defects of the
Product could be discovered, Customer shall bear the costs that Company incurred as a result of the notice.
It shall be in Company’s sole discretion to determine if the Product has a defect.
1.5. With respect to orders made to custom, any defects of the Products caused by Customer’s
specifications are excluded from the warranty set forth in 1.1.
1.6. Company also makes no warranty that the Products manufactured under an order made to custom
do not infringe the intellectual property or other proprietary rights of any third party and Customer is solely
responsible for assuring that such Products do not so infringe.
1.7. The “Warranty Period” begins on the date of delivery of the Product to Customer, and continues to
be in effect for two (2) years.
1.8. Company does not authorize any person or party to assume or create for it any other obligation or
liability in connection with the Products except as set forth herein.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 16 / 32
1.9. All requests and notices under this Warranty shall be directed to:
ACD Elektronik GmbH
Engelberg 2
88480 Achstetten
Germany
Phone: +49 7392 708-0
Email: [email protected]
1.10. THE WARRANTY SET FORTH IN SECTION 1.1 IS MADE IN LIEU OF ALL OTHER WARRANTIES
(WHETHER EXPRESS OR IMPLIED), RIGHTS OR CONDITIONS, AND CUSTOMER ACKNOWLEDGES
THAT EXCEPT FOR SUCH LIMITED WARRANTY, THE PRODUCTS ARE PROVIDED “AS IS.” COMPANY
SPECIFICALLY DISCLAIMS, WITHOUT LIMITATION, ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, OF ANY KIND, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, AND
THOSE WARRANTIES ARISING FROM A COURSE OF PERFORMANCE, A COURSE OF DEALING OR
TRADE USAGE.
2. Limitation of Liability:
2.1. IN NO EVENT SHALL COMPANY BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE,
SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, DAMAGES FOR LOSS
OF PROFITS, REVENUE, GOODWILL OR USE, INCURRED BY CUSTOMER OR ANY THIRD PARTY,
WHETHER IN AN ACTION IN CONTRACT, TORT, STRICT LIABILITY, OR IMPOSED BY STATUTE, OR
OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. COMPANY’S LIABILITY
FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THIS AGREEMENT SHALL IN NO EVENT
EXCEED THE PURCHASE PRICE OF THE PRODUCTS. IT IS AGREED AND ACKNOWLEDGED THAT
THE PROVISIONS OF THIS AGREEMENT ALLOCATE THE RISKS BETWEEN COMPANY AND
CUSTOMER, THAT COMPANY’S PRICING REFLECTS THIS ALLOCATION OF RISK, AND BUT FOR
THIS ALLOCATION AND LIMITATION OF LIABILITY, COMPANY WOULD NOT HAVE ENTERED INTO
THIS AGREEMENT.
2.2. IN JURISDICTIONS THAT LIMIT THE SCOPE OF OR PRECLUDE LIMITATIONS OR EXCLUSION
OF REMEDIES OR DAMAGES, OR OF LIABILITY, SUCH AS LIABILITY FOR GROSS NEGLIGENCE OR
WILLFUL MISCONDUCT OR DO NOT ALLOW IMPLIED WARRANTIES TO BE EXCLUDED, THE
LIMITATION OR EXCLUSION OF WARRANTIES, REMEDIES, DAMAGES OR LIABILITY SET FORTH
ABOVE ARE INTENDED TO APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.
CUSTOMER MAY ALSO HAVE OTHER RIGHTS THAT VARY BY STATE, COUNTRY OR OTHER
JURISDICTION.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 17 / 32
8 Volumen de suministro
El paquete consta de los siguientes artículos:
1 Dispositivo, incl. batería
2 Batería de repuesto (opcional)
3 Estación de carga (opcional)
4 Kit de conexión para la estación de carga, dos piezas (opcional)
5 Resumen breve del set M210SE, M210SE/DS210 (manual de inicio rápido)
Compruebe que el paquete esté completo y no presente daños.
Figura 10: contenido del paquete
ATENCIÓN
La batería del M210SE es una batería de iones de litio. Las baterías
de iones de litio pueden explotar si se exponen al fuego. No
desmonte la batería ni la exponga al fuego ni al calor (superior a
140 °F).
ATENCIÓN
No coloque nunca el dispositivo cerca de fuentes de calor
(calefactores o equipos similares) y nunca lo exponga a la luz
solar directa, a fuentes de polvo excesivo ni a impactos.
ATENCIÓN
El lápiz táctil solo se puede usar para manejar la pantalla táctil. No
se debe usar para otros fines.
1
2
3
4
4
5

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 18 / 32
9 Uso previsto
El set del sistema de adquisición de datos M210SE (M210SE/DS210) es una solución para la adquisición y
transferencia móvil de datos. No use el sistema en zonas geográficas en las que se puedan usar
explosivos.
Observe toda la información de advertencia relacionada con el uso de dispositivos inalámbricos.
El kit de conexión suministrado (consulte el punto 8) solo está indicado para usarse con el set M210SE.
NOTA
Se ha comprobado que este equipo cumple con los límites de los dispositivos
digitales de clase A, de acuerdo con el apartado 15 de las normas de la FCC
Estos límites se han establecido para proporcionar una protección razonable
contra interferencias perjudiciales cuando el equipo se usa en un entorno
comercial Este equipo genera, usa y puede emitir energía de
radiofrecuencia y, si no se instala ni se usa siguiendo el manual de
instrucciones, puede producir interferencias en algunas comunicaciones por
radio
NOTA
Este dispositivo cumple el apartado 15 de la normative FCC El
funcionamiento está sujeto a las siguientas dos condiciones: (1) este
dispositivo no debería causar interferencias perjudiciales y (2) este
dispositivo debe aceptar cualquier interferencia, incluyendo las
interferencias que puedan causar un funcionamiento no deseado del
dispositivo
NOTA
Los cambios o las modificaciones no autorizados de forma expresa por la
parte responsable del cumplimiento podrían suponer una infracción de la
autoridad del usuario para operar el equipo

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 19 / 32
10 Manipulación
¡Lea todas las instrucciones antes de usar el M210SE!
¡No beba alcohol ni tome drogas al usar el M210SE y siga
atentamente las instrucciones de seguridad!
10.1 Antes de la primera puesta en funcionamiento del M210SE
Para asegurarse de que la batería insertada en fábrica en el dispositivo esté completamente cargada,
coloque el dispositivo en la estación de carga DS210 suministrada (si se incluye en el volumen de
suministro) y consulte también la sección 10.2. Usando la unidad de alimentación suministrada, conecte la
estación de carga a la toma eléctrica (el LED Power muestra una luz verde) y consulte también la sección
10.2.
El proceso de carga de la batería se ha completado cuando el LED 'CHARGE' esté en verde.
Ahora puede usar el terminal de mano M210SE.
Puede ver el proceso de carga de la batería en la Figura 11.
ATENCIÓN
Solo pueden usarse unidades de alimentación ACD originales y
baterías autorizadas por ACD con el M210SE y la DS210. El uso de
componentes no autorizados puede causar la destrucción del
dispositivo. Retire la batería del dispositivo si no lo va a usar
durante un período prolongado de tiempo.
ATENCIÓN
La batería del M210SE es una batería de iones de litio. Las baterías
de iones de litio pueden explotar si se exponen al fuego. No
desmonte la batería ni la exponga al fuego ni al calor (superior a
140 °F).
ATENCIÓN
Antes de cada uso, deben inspeccionarse el terminal de
adquisición móvil de datos, la estación de carga y los cables de
conexión en busca de daños. Las piezas dañadas deben
sustituirse. Contacte con ACD en cualquiera de los casos.

M210SE_Lidl_Brief_Overview_FCC_V1.04_en_es.doc 20 / 32
1 2 3
4 5 6
Figura
11
: proceso de carga
1: 1.
er
LED verde: la estación de carga tiene corriente
2.º LED rojo: la batería del dispositivo se está cargando.
2: 1.
er
LED verde: la estación de carga tiene corriente
2.º LED verde: la batería del dispositivo está totalmente cargada.
3: 1.
er
LED verde: la estación de carga tiene corriente
2.º LED verde: la batería del dispositivo está totalmente cargada.
3.
er
LED rojo: la segunda batería se está cargando.
4: 1.
er
LED verde: la estación de carga tiene corriente
2.º LED verde: la batería del dispositivo está totalmente cargada.
3.
er
LED verde: la segunda batería está totalmente cargada.
5: 1.
er
LED verde: la estación de carga tiene corriente
3.
er
LED rojo: la segunda batería se está cargando.
6: 1.
er
LED verde: la estación de carga tiene corriente
3.
er
LED verde: la segunda batería está totalmente cargada.
This manual suits for next models
1
Table of contents
Languages:
Other ACD GRUPPE Touch Terminal manuals