Hafele WT 210 User manual

Version 7.12.2015
MOUNTING INSTRUCTIONS
WT 210 Wall Terminal
Access control with experience

25
Information for instructions
Information for the mounting instructions
These instructions make it possible to safely assemble and install the WT 210 wall terminal as constituent of an
access control system. The instructions are a constituent of the system, and must be kept in close proximity to
the system in a location where they are accessible to the personnel at all times.
The personnel must have carefully read and understood these instructions before starting any work. A basic
prerequisite for safe working is adherence to all of the specified safety instructions and handling instructions in
these instructions.
The local occupational safety regulations and the general safety regulations for the area of application of the
system apply as well.
Associated documents
As well as these assembly and mounting instructions, the following document is valid for the access control
system:
Power supply delivery documentation
Dialock 2.0 user manual

26
1Overview of the access control system................................................................................................28
2Safety........................................................................................................................................................29
2.1 Symbols in these instructions.........................................................................................................29
2.2 Intended use...................................................................................................................................31
2.3 Safety marking ...............................................................................................................................32
2.4 Residual risks.................................................................................................................................32
2.5 Operator responsibility ...................................................................................................................34
2.6 Personnel requirements.................................................................................................................34
2.7 Protecting the environment ............................................................................................................35
3Function description...............................................................................................................................36
3.1 Function of the access control system...........................................................................................36
3.2 WT 210 pin assignments................................................................................................................36
3.3 Recommended power supply.........................................................................................................37
3.4 Installation versions........................................................................................................................37
3.4.1 Installation version 1: Door with WT 210, electric strike and pushbutton on the inside............37
3.4.2 Installation version 2: Door with WT 210, electric strike and sabotage protection ...................38
3.4.3 Front view of WT 210................................................................................................................38
4 Assembly and installation......................................................................................................................39
4.1 Installation location requirements...................................................................................................39
4.2 Assembly and installation of the WT 210.......................................................................................39
4.3 After installation..............................................................................................................................41
4.4 Indicators of the WT 210................................................................................................................42
5 Dismantling, disposal.............................................................................................................................43
5.1 Safety instructions pertaining to dismantling/disposal ...................................................................43
5.2 Dismantling.....................................................................................................................................43
5.3 Disposal..........................................................................................................................................43
6 Technical data .........................................................................................................................................44
6.1 Mechanical dimensions WT 210 ....................................................................................................45
7 Appendix..................................................................................................................................................47

28
1 Overview of the access control system
Short description
The WT 210 is a compact wall terminal which combines the reader and the control electronics in a compact
unit. In combination with an electric door strike the WT 210 forms a complete offline access point.
The design of the WT 210 allows an easy installation in DIN 49073 flush-mount sockets.
The WT 210 has an opto-isolated input. This can be used to connect a pushbutton inside the protected area
which directly activates the switch output of the WT 210 for the electric strike.
The WT 210 has a tamper switch, which is triggered when the reader is removed from the mounting frame, and
it activates the integrated acoustic signal generator and the alarm relay. The alarm relay can be used to set up
a manipulation-proof access point in combination with an additional relay that is installed in the protected area.
All locking events and every removal of the device from the frame are logged in the memory of the WT 210.
The WT 210 has an RF interface through which the terminal can be configured and the audit trail can be read
out with the MDU.
WT 210 Wall Terminal
Fig. 1: WT 210 for installation in flush-mount socket, front view WT 210 rear view

29
2 Safety
2.1 Symbols in these instructions
Safety instructions
Safety instructions are marked with symbols in these instructions. The safety instructions are initiated by signal
words that indicate the extent of the hazard.
DANGER!
This combination of symbol and signal word indicates a directly dangerous situation which could lead to
death or serious injuries if it is not avoided.
WARNING!
This combination of symbol and signal word indicates a potentially dangerous situation which could lead to
death or serious injuries if it is not avoided.
CAUTION!
This combination of symbol and signal word indicates a potentially dangerous situation which could lead to
slight or minor injuries if it is not avoided.
NOTE!
This combination of symbol and signal word indicates a potentially dangerous situation which could lead to
property damage if it is not avoided.
NOTE!
This combination of symbol and signal word indicates potential environmental hazards.

30
Safety instructions in action instructions
Safety instructions can relate to certain individual directives. Safety instructions such as this are embedded in
the directives so that they do not interrupt the flow of reading when performing the action. The signal words
that have been described above are used.
Examples:
1.> Loosen screw.
2.>
CAUTION!
Risk of trapping cable at cover!
Pay attention to the position of the cable. Carefully close cover.
3.> Tighten screws.
Special safety instructions
The following symbols are used in safety instructions to draw attention to particular dangers:
Warning symbol
Type of danger
Warning of dangerous electrical voltage
Warning of a hazardous area
Tips and recommendations
This symbol highlights useful tips and recommendations and information for efficient and problem-free
operation.

31
Other markings
The following markings are used in these instructions to highlight action instructions, results, lists, references
and other elements:
Marking
Explanation
1.>, 2.>, 3.> ...
Step by step action instructions

Results of actions
References to sections of these instructions and associated documents
Lists without a fixed order
[Pushbutton]
Controls (e.g. buttons, switches), display elements (e.g. signal lamps)
2.2 Intended use
The WT 210 is exclusively intended for use in an access control system.
The indented use also includes adherence to all of the specifications in these instructions.
Any other type of use is considered as a misuse of the system.
WARNING!
Danger in the event of misuse!
Misuse of the WT 210 can lead to hazardous situations.
- Never install the WT 210 in potentially explosive areas.
- Never install the WT 210 in other environmental conditions than those that are permitted.

32
2.3 Safety marking
The following labels can be found on one or more components of the access control system. They relate to the
immediate environment in which they are affixed.
Electrical voltage
Only electrical experts are allowed to work on components bearing this marking.
Unauthorised persons are not permitted to open cabinets bearing this marking.
Crossed-out waste bin
This picture indicates that the respective component may not be disposed of with the domestic
waste.
Do not touch
Parts may be destroyed if they are touched.
Lead
The conductor board does not contain any lead.
2.4 Residual risks
The components have been designed in accordance with the state of technology and in accordance with the
latest safety requirements. Nevertheless, residual risks may still be present that require caution. The residual
risks and the resulting actions and measures are listed in the following.

33
Electric current
DANGER!
Risk of fatality due to electric current!
If you come into contact with live components there is a direct risk of death by electrocution.
Damage to the insulation or individual components can put your life at risk.
- Have all work on the electrical system carried out by electric experts.
- In the event of damage to the insulation, switch off power supply immediately and have it repaired.
- Before starting to work on live parts of electrical systems and operating materials, disconnect the system
from the mains and secure it against reconnection whilst the work is being carried out. When doing this,
pay attention to the 5 safety rules:
- Disconnect from the mains.
- Secure against reconnection.
- Verify that the system is dead.
- Carry out earthing and short-circuiting.
- Provide protection from adjacent live parts.
- Never bypass or disable fuses. Adhere to the correct current rate specification when replacing fuses.
- Keep moisture away from live components. It can lead to short circuits.