Acewell ACE-100- User manual

ATV/Motorcycle Computer
ACE-1000/1100 User Manual
12
3
4
7
9
MADE IN TAIWAN
RESET
10R-029648
RESET
5 6
8
PANEL DESCRIPTIONS
1. Tachometer Scale
2. Bar Tachometer
3. Other funcons
4. Thermometer*
5. RESET Buon
6. MODE Buon
7. Fuel Gauge
8. RPM Warning Indicator
9. Temperature*/Fuel gauge
warning LED
FUNCTIONS
SPECIFICATIONS
Power Input
Tachometer Sensor
Temperature Sensor*
Power Consumption
Dimensions
DC 12V
CDI or Ignition Coil Signal
Thermo Sensor
50uAat clock mode
1mAat on status without backlight and all sensors off
2mAat all sensors on status without backlight
15mAat on status with 3 sec. backlight
25mAat on status with continue backlight
110.0mm x 55.0mm x 21.5 mm)
Function Specifications
Simbolo
Bar Tachomete 500-10,000 rpm
1,000-20,000rpm options
100-19,900rpm
Total Hour Meter 0-999999H
Digital Tachometer
Maintain Reminder 1-9999 hours
Hour meter 1&2 0-99H59`59``
100Ω, 250Ω, 500Ω options or
1-7 Bar-graphic
Maximum Thermometer*
Voltage Gauge* V 8.0-18.0 Volt
Digital Thermometer*
rpm
12/24 Hour Clock 0:00`-11H59`/23H59`
RT 1&2
Bar-Fuel Gauge
RT1
or RT2
10R-029648
RPM sensing wire mounting:
1. Signal intensity from ignion coil is dependent on vehicle type.
2. Circles 2-5 turns around ignion coil, with more turns creang
steadily stronger signal, fewer turns creang weaker signal.
3. The RPM circuit is designed for most bikes, however paral
bikes’ signal is too strong if the RPM looks like much more than
actual RPM and unstable, please serial connect the aached 1M
Ohm resistor to solve it.
2-5
CDI Ignition Coil
Tuns
RPM-INPUT
Either One
Thermo Sensor and Sensor Tube* :
1. The unit includes a water temperature sensor; you have to
purchase a suitable water pipe temperature sensor tube to
install the sensor easily. It is not need to purchase sensor
tube in case your bike matches PT1/8 temperature sensor
and the aachment is PT1/8 sensor.
2. Cut the water pipe, insert the temperature tube into the
pipe and secure it by aached pipe clamps.
3. Screw the sensor into the tube.
BAR RPM: Bar Graphic Tachometer
The bar tachometer has 10,000rpm and 20,000rpm opons.
RPM: Digital Tachometer
1. It displays digital tachometer up to 19,900RPM.
2. Tachometer signal can pick up from either CDI or
Ignion Coil Signal.
Shift Warning RPM
1. The funcon enables you to set up a shi warning RPM.
2. Shi warning LED indicator flashes when RPM reaches
seng value, and stop flash aer you shi gear.
RT 1&2: Hour Meter 1&2
1. Calculates total engine operaon me from last RESET.
2. Count automacally begins with engine starng.
TT: Total Hour Meter
1. Calculates total engine operaon me from the
beginning of the computer.
2. TT data is stored in memory, and couldn’t be reset.
: 12/24 hour Clock
It displays 12 or 24 hour current me.
: Digital Thermometer*
1. The thermometer always displays on the right side of the screen.
2. It displays -L- C or -L- F when temperature is lower than
50 C or 122 F, and displays -H- C or –H- F when
temperature is over 180 C or 356 F.
3. The thermometer digits and warning LED indicator flash when
the thermo sensor detects temperature over the preseng
warning temperature.
FEATURES
Displays bar-graphic tachometer, digital thermometer*,
bar fuel gauge and one addional funcon at the same me.
Bar-graph tachometers with selectable 10,000rpm or
20,000rpm redline.
Two sets of maintenance reminders to remind you it is me to service
your bike.
Fuel gauge includes 100, 250 and 510 Ohm opons for fuel meter
input resistance, as well as “fuel gauge off” mode.
Includes main unit, bracket, RPM sensing wire, thermo sensor*,
fing kits and wiring harness.
Thanks for bought the ATV/Motorcycle computer; this manual is designed for ACE-1000/1100 series.
ACE-1000 does not have funcons of thermometer and volt meter; *all descripons relave to these funcons are for ACE-1100 only.
English
INSTALLATION
Rubber Pad
Washer
Spring Washer
Fixing Screw Nut
Main Unit
Mounng
Main Unit Mounting

SHIFT WARNING RPM OPERATION
1. Press MODE buon to the RPM screen; pull on the throle
unl the desired shi warning RPM.
2. Press RESET buon to confirm and set up the shi warning RPM.
3. Bar-graphic tachometer and warning LED will flash to warning
you shi gear.
4. Press RESET buon for 2 seconds at the RPM screen to re-adjust
the shi warning RPM.
Backlight of Internal/Bike’s Powers:
1. The computer built-in a CR2032 baery for off road bikes in
case take away bike’s baer to reduce weight.
2. You can use both internal baery and bike’s baery at the
same me.
3. The backlight is always turned on if you connect to bike’s baery.
4. Each press of either button turns on backlight for 3 seconds then
turn off automacally when uses CR2032 only.
BUTTON OPERATIONS
MODE BUTTON
Press the MODE buon to move all funcons in loop sequence
from one funcon screen to another.
RESET BUTTON
1. Press MODE buon to get to the desired screen then press RESET
buon for 2 seconds to reset hour meter, MAX thermometer*,
and MAX RPM data from stored values to zero individually.
2. TT data cannot be reset.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
MAX C or F : Maximum Thermometer*
Displays highest temperature achieved aer last Reset operaon.
Volt: Digital Voltage Gauge*
It checks bike’s baery and charging systems health.
Fuel Gauge
1. Has 7 bars to indicate how much fuel remains.
2. Built-in 100, 250, 510Ohm, oFF, -100, -250 and -510 Ohm
fuel sender resistance, the fuel bars will disappear when
you select “oFF” mode.
3. The full bars are low resistance and empty bar is high
resistance for 100, 250 and 510ohm; -100, -250 and -510
ohm are the inverse.
4. Last bar flashes to indicate low fuel level automacally.
Bars -250Ω-100Ω510Ω250Ω100Ω
7
6
5
4
3
2
1
0-Flash
0-10
11-20
21-35
36-45
46-60
61-75
76-90
91-100
0-25
26-50
51-85
86-110
111-150
151-200
201-230
231-250
0-50
51-100
101-180
181-230
231-300
301-380
381-460
461-510
100-90
89-75
74-60
59-45
44-35
34-20
19-10
9-0
250-230
229-200
199-150
149-110
109-85
84-50
49-25
24-0
-510Ω
510-460
459-380
379-300
299-230
229-180
179-100
99-50
49-0
RT1 or RT2: Maintenance Reminders
1. It has 2 maintenance reminders RT1 and RT2, which count
down the preset entered me RT1 & RT2 since last RESET.
2. It accumulates RT1&RT2 when the count down reaches to
“0 ”, and symbols of “ RT1 or RT2” flash to remind you to
maintain oil or parts.
3. Push and hold RESET buon to reset and restart the
maintenance reminder aer changing oil or parts.
AUTO Power Off :
1. The power will be turned off automacally aer 3 minutes the
unit does not receive any signal from speed, RPM or buon
operaon in case it is using the internal baery CR2032.
2. The riding data will be kept in memory at each power off before
the low baery icon appears.
3. The power is always turned on at LAP mode unl go out the LAP
mode.
:Low Battery Indicator
1. The “ “ icon flashes when the CR-2032 baery is at low power
status to reminder you change the baery.
2. All seng is kept in memory not mater the power is connected to
bike’s 12VDC baery or using internal CR2032 baery only; In case
the power is only the internal CR2032 baery, the unit can display
riding data but can’t be kept in memory when the low baery icon
appears in order to avoid seng data be reset at low voltage, that
means riding data from last memory unl the“ “ con appears is
lost.
3. Remove the old baery. Replace with a new CR2032 with the posive
(+) pole towards the baery cap.
4. Be sure to press RESET buon at the rear side aer installed the
baery to sure all funcons work smoothly.

RESET+
MODE
2 Sec
RESET
Mode
Mode
Mode
Mode 2 Sec
Mode
RESET
Mode
Mode
Clock: Hour
Clock: Minute
RPM: 10,000 / 20,000
RPM Warning: 1000 ~19,900
Engine Signal: 0.5/1.0/2.0/3.0
Mode
Mode
Fuel Type: 100 / 250 / 510 / off
Maintain Reminder 1: 1~9999
Temp. Warning: 40 ~ 180 C
Mode
Mode
Mode
Unit: C / F / off
Maintain Reminder 2: 1~9999
Mode
1 Setup operaons include 12/24 hour clock, bar rpm scale, shi
warning RPM, numbers of engine rotaon per signal, units of
thermometer*, temperature warning*, fuel meter input resistance
selecon and maintain reminder seng. These must be set up step
by step. The computer will be automac reversion to normal mode
if no buon operaon for 75 seconds at any seng screen.
2. Press both MODE & RESET buons to go into seng screen. In
seng screens, each press RESET buon to add the flashing digit
by 1 or convert units, press MODE buon to confirm the digit
seng and jump to next digit or next seng screen to be set.
Press MODE buon for 2 seconds at any seng screen to finish
the seng and go to normal mode.
3. It displays " 12 or 24H, “ XX:XX " and “A” or “P” symbols in case you
select 12H. Operates buons as descripons of item 2 to finish
clock seng and jump to 10,000/20,000rpm scale seng.
4. It displays 10,000rpm scale, press RESET buon to convert 10,000
or 20,000rpm. Press MODE buon to confirm the seng and jump
to shi RPM warning seng.
5. It displays the default "r 06500", the digit “0” flash. Follow the item
2 of buon operaon to finish the shi RPM warning seng and
jump to engine specificaon seng.
6. It displays "RPM SPC-X.X", the default value is 1.0; there are 4
opons: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine
rotaon per signal. For example the value 2.0 means the engine
rotate 2 turns to output a signal.
7. Press RESET buon to move in loop sequence from one to another
value of the 4 values. Press MODE buon to confirm the seng
and go to temperature unit seng screen.
8. It displays " C , F or oFF ", each press of RESET buon converts C, F
or OFF, the temperature icon and digits will disappear when you
select oFF mode; press MODE buon to confirm temperature seng
and jump to temperature warning seng.
9. It displays "XXX" and the selected unit. Follow the item 2 of buon
operaon to finish the temperature warning seng and go to fuel
sensor resistance seng.
10. It displays “100r” and fuel tank symbol, follow the item 2 to select
100r, 250r, 510ohm or oFF and jump to maintain reminder seng..
The fuel meter bar will disappear if you select oFF mode.
11. It displays “ RT1 or RT2 “symbols and “ XXXX ”, the default of RT1
is 3 hours and RT2 has default of 10 hours, follow item 2 to seng a
desired hours of maintain reminders and jump to normal mode.
Clock, RPM,Temperature and fuel meter SET UP