Acewell ACE1 Series User manual

ATV/Motorcycle Computer
ACE1XX User Manual
2
1
6
4 5
Speed Sensor:
The ACE-1XX can use either a 2 wire hall sensor or a reed sensor
when it is connected to the bike’s power.
1. 1 row: Speedometer
2. 2 row: Trip 1&2, RT, AVG
3. Fuel Gauge: 1-7 bar-graphic display
4. RESET Buon
5. MODE Buon
6. LED Indicators
st
nd
FEATURES
Digital LCD displays mul-funcons ATV/Motorcycle and Scooter
computers.
Built-in 3 LED indicators for different applicaons and backlight.
Odometer and total riding mer are always kept in memory.
Metric/Empire unit opons are available.
Adjustable wide wheel circumference seng from 1 to 3999mm.
Fuel gauge includes +/- 100, 250 and 510 Ohm opons for fuel sender
input resistance, as well as “fuel gauge off” mode.
Includes bracket, speed sensor, fing kits and wiring harness.
SPECIFICATIONS
Power Input
Speed Sensor
Wheel circumference setting
Dimensions
DC 9-18V
Reed Sensor or Hall sensor with 2 wires
1mm-3999mm
96.7mm x 53.9mm x 24.5 mm
Function Specifications
Simbolo
Speedometer 2.4-399.9 km/h
(248 MPH)
0.0-999.9 KM/Miles
Maximum speed 2.4-399.9 KM/h (248 MPH)
Trip meter 1&2
Riding timer 0-99H59`59``
+/- 100Ω, 250Ω, 500Ω options and Off
Total Riding Time 0-999999H
Odometer
TRIP 1/2
12/24 Hour Clock 0:00`-11H59`/23H59`
RT
Bar-Fuel Gauge
Km/H /
MPH
0- 999999 KM, 0-624999 Miles
ODO
Average speed
AVG
2.4-399.9 KM/h (248 MPH)
MAX
T T
INSTALLATION
Rubber Pad
Washer
Spring Washer
Fixing Screw Nut
Reed Speed Sensor and Magnet:
1. This sensor is universal sensor for motorcycle, find a rotang part
to install magnet (for example disk, sprocket or drivesha) and a
locaon to install the sensor where it can be aligned to the magnet.
2. Align the center of the magnet to either of the sensor marking lines
or the side of the sensor.
3. Installing the sensor parallel to the vibraon direcon creates
oponal an-vibraon effect.
4. Make sure the gap between the magnet and the sensor is
within 8mm.
Hall Effective Speed Sensor and Magnet:
1. This is universal sensor for ATV front or rear wheel installaon
or motorcycle front wheel installaon. For some fitments an
accessory speed sensor holder may need to be purchased.
2. Find a rotang part to install magnet (for example disk, sprocket
or drivesha) and a locaon to install the sensor where it can be
aligned to the magnet
3. Align the center of the magnet to center of side face of the sensor.
4. Make sure the gap between the magnet and the sensor is
within 5mm.
Specific Hall sensors:
Cable drive adaptors for most bikes originally fied with cable
driven speedometers or milemeters are available. When using these
cables it is necessary to divide the circumference seng by the
number of rotaons of the cable per rotaon of the wheel.
Left-Direction Indicator/Green
Main-Beam Headlamp/Blue
Right-Direction Indicator/Green
Hazard Warning/Red Direction Indicator/Green
Engine Oil /Red
Neutral Gear /Green
Reverse Gear /Red
R
N
Thanks for purchasing this ATV/Motorcycle/Scooter computer; this manual is designed for ACE-1XX series. Each model has 3 LED indicators.
Different model has different LED indicators. You may found above photo has different LED indicators from your computer; the photo above is for reference only.
3
Max. 8mm
Vibration Direction
sensor
Max. 8mm
Vibration Direction
sensor
Max. 8mm
Main Unit Mounting
Main Unit
Mounng
PANEL DESCRIPTIONS
English
10R-039949

BUTTON OPERATIONS
MODE BUTTON
Press the MODE buon to move between all funcons in loop
sequence as “→ ” path from one funcon screen to another.
1. Setup operaons include 12/24hour clock,, wheel circumference,
units and fuel meter input resistance selecon. These must be
set up step by step. The computer will be automac reversion to
normal mode if no buon operaon for 75 seconds at any seng
screen.
2. Press both MODE & RESET buons to go into seng screen. In
each seng screen, press RESET buon to increment the flashing
digit by 1 or convert units, press MODE buon to confirm the digit
seng and jump to next digit or next seng screen to be set. Press
MODE buon for 2 seconds at any seng screen to finish the seng
and go to normal mode.
3. It displays "12 or 24H and XX:XX-XX" symbols as well AM/PM in
12H mode. Operates buons as per descripons of item 2 to finish
clock seng and jump to wheel circumference seng.
4. In "cXXXX" display, "c" means "Circumference", following 4 default
digits; flashing digit is digit to be set. Follow the item 2 of buon
operaon to finish the wheel circumference seng and jump to
unit seng.
5. It displays KM/H or MPH, each press of RESET buon switches
units; press MODE buon to confirm unit seng and jump to fuel
sensor resistance seng.
6. It displays “100r” and fuel tank symbol, follow the item 2 to select
100, 250, 510ohm, -100, -250, -510Ohm or OFF and jump to jump
to clock seng or return to Normal Mode. The fuel meter bar will
disappear if you select oFF mode.
RESET BUTTON
1. Press MODE buon to get to the desired screen then press
RESET buon for 2 seconds to reset Trip 2, MAX SPD and
AVG speedometer from stored values to zero individually.
2. The data of Trip 1, AVG & RT can be reset at the same me
when one of the 3 data funcons is being reset.
3. ODO, clock and TT data cannot be reset.
Mode
FUNCTIONS
Km/H or MPH: Speedometer
Displays speed meter up to 399 Km/H or 248 MPH.
MAX: Maximum Speed Meter
Displays highest speed achieved since last Reset operaon.
AVG: Average Speed Meter
It calculates average speed since last RESET. The AVG is calculated
from TRIP 1 be divided by RT.
TRIP 1&2: Trip Meter 1 and 2
TRIP funcon accumulates trip distance since last RESET as long as
bike/vehicle is in moon.
ODO: Odometer
ODO accumulates total accumulated distance traveled during
bike moving.
RT: Riding Timer
1. Calculates total running me since last RESET.
2. Count automacally begins with movement.
TT: Total Riding Time
1. Calculates total riding me traveled during bike moving.
2. TT data is stored in memory, and cannot be reset.
: 12/24 hour Clock
It displays 12 or 24 hour current me.
: Fuel Gauge
1. Have 7 bars to indicate how much fuel remains.
2. Built-in +/- 100, 250 and 510Ohm fuel sender resistance,
the fuel bar display will disappear in when you select “ off ”
mode.
3. Last bar flashes to indicate low fuel level automacally.
Mode
Mode
Mode
WHEEL CIRCUMFERENCE TABLE
Tire SizeCircumferen
ce number
(mm)
Tire SizeCircumferen
ce number
(mm)
Tire SizeCircumferen
ce number
(mm)
23 inch
24 inch
25 inch
26 inch
19 inch
20 inch
21 inch
22 inch
15 inch
16 inch
17 inch
18 inch
1835
1915
1995
2075
1516
1596
1676
1756
1197
1277
1357
1436
1. The details below have been calculated using following formula: Tire
Diameter (inches) x 25.4(mm/inches) x 3.1416 = wheel circumference
(in mm).
2. Idenfy the re size of your ATV/Motorcycle when you need to change
different re size and key in the corresponding number shown in the
following chart.
3. The computer calculates the wheel rotang length between 2 passes
of the magnet; use this table to find the sengs when you are using
a reed sensor or an universal hall sensor with magnet to measure
your speed.
4. If you are using a cable drive speed sensor then divide the number in
the above table by the number of turns of the cable drive for each
revoluon of the wheel. For example if 1 wheel revoluon equals
5 turns of speed cable then the wheel circumference has to be
divided 5.
5. You can use more magnets, but the wheel circumference seng
must be divided by the number of magnet you installed.
Mode
Mode
Mode
Mode
Clock,Wheel Circumference,Units and Fuel Gauge Resistance SET UP

RESET+
MODE
2 Sec
RESET
Mode
Mode
Mode
Clock: Hour
Clock: Minute
Mode
Wheel Size: 1 ~ 3999 mm
Unit: KM/H / MPH
Fuel Type: 100/250/510/-100/-250/-510/off
Clock,Wheel Circumference,Units and Fuel Gauge Resistance SET UP
Mode
Clock: Second
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
Mode
Mode
Mode
2 sec