ACME MEGA STROBE 5000 RGB User manual

MEGA STROBE 5000 RGB
LED-ST5000 RGB
User Manual
Please read the user manual before use

1 E
Table of Contents
1，Safety Information…………………………………………………. 2
2，Rear Panel…………………………………………………………. 4
3，Preparation for Use ………………………………………………...4
4，Main Function …………………………………………………….. 5
5，Remote Control…………………………………………………….13
6，Technical Specification…………………………………………….15

2 E
1. Safety Information
Warning: This product is for professional use only! It is not for
household use.
The LED-ST5000 RGB presents risks of lethal or severe injury due to fire
and heat, electric shock, ultraviolet radiation, and falls. Flashing light is
also known to trigger epileptic seizures in persons who are photosensitive.
Read this manual before powering or installing the fixture, follow the
safety precautions listed below and observe all warnings in this manual
and printed on the fixture.
Noted: high voltage in the LED board!
Super power strobes, so please avoid extended periods of
continuous flashing
To guard against electric shock
Do not remove the rear cover: there are no user-serviceable parts inside.
Always ground (earth) the fixture electrically.
Use only a source of AC power that complies with local building and electrical
codes and has both overload and ground-fault protection.
Do not expose the fixture to rain or moisture.
To guard against UV radiation, burns, and fire
Never operate the fixture with the front glass open, missing or damaged.
Do not stare directly into the light. Never look at an exposed LED while it is lit.
Never attempt to bypass the fuse. Always replace defective fuses with ones of the
specified type and rating.
Verify that the power feed cable is rated for the current draw of all connected
fixtures.
Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters
(20 inches) away from the fixture. Keep flammable materials well away from the
fixture.
Minimum distance to illuminated surface is 10 meters.
Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

3 E
Never place filters or other materials over the front glass cover.
The exterior of the fixture can reach temperatures up to 120° C (248° F). Allow the
fixture to cool for at least 15 minutes before handling.
Do not modify the fixture or install other than genuine parts.
Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104°
F).
To guard against falls
When suspending the fixture above ground level, verify that the structure can hold
at least 10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
Block access below the work area whenever installing or removing the fixture.
To guard against epileptic seizure
Do not operate the fixture near stairways.
Provide advance notice that strobe lighting is in use.
Avoid extended periods of continuous flashing, particularly at frequencies of 10 to
20 flashes per second.

4 E
2. Rear Panel
1, Circuit Breaker
2, Main Power
3. LED display
4, Menu /UP/DOWN/ Enter button
5, DMX signal/ Flash indicator
6, DMX input/output
3. Preparation for Use
Table1: Cord cap wirings
INSTALLATION
The LED-ST5000 RGB may be installed in any orientation. The mounting bracket
provides five 12 mm holes for direct fastening or attachment of rigging clamps.
To install the mounting bracket
1. Place the fixture face down on a table.

5 E
2. Place an aluminum washer on each mounting bracket stud.
3. Make clear the direction of left and right side of bracket and lock the screws. After
that, tighten one hand knob to lock the mounting bracket in one end of bracket.
4. MAIN FUNCTION
Press MENU button enter the function, then use UP/DOWN or MENU button
to select the function you want, final press ENTER button to confirm the
function you select. Wait for 30 seconds, it will return to main interface. If
you want back to main menu, please hold MENU button for 1 second. The
main menu as follow:
4.1 DMX 512 address setting
Select ADDR option and the display will blink, press ENTER button to
confirm your selection. You can check the current DMX address from LED
display. The DMX address can be changed by press UP/DOWN button and
then press ENTER button to confirm your selection. Wait for 30 seconds, it
will return to main interface. If you want back to main menu, please hold

6 E
MENU button for 1 second.
4.2 Channel mode setting
Select CHMD option, press ENTER button to confirm your selection. Change
the channel way (1/2/3/4/6/7) by press UP/DOWN button. Press ENTER
button to confirm your selection. Wait for 30 seconds, it will return to main
interface. If you want back to main menu, please press MENU button.
4.3 LED display setting
Select the LED option, press ENTER button to confirm your selection. You
can see the current ON/OFF status of LED display now. You can change its
status by press UP/DOWN button. Then press ENTER button to confirm your
selection. If you choose OFF, than the LED display will close without any
operation for I min. Wait for 30 seconds, it will return to main interface. If you
want back to main menu, please hold MENU button for 1 second.
4.4 LED display direction setting
Select DISP option, press ENTER button to confirm your selection. Select
the DISP / DSIP by press UP/DOWN button. Press ENTER button to confirm
your selection. Wait for 30 seconds, it will return to main interface. If you
want back to main menu, please hold MENU button for 1 second.
4.5 White Balance
Select BALA option, press ENTER button to confirm your selection. Select
the RED,GREE,BLUE by press UP/DOWN button, Press ENTER button to
confirm your selection, then adjust the current DMX address byUP/DOWN
button, and Press ENTER button to confirm.Or Wait for 30 seconds, it will
return to main interface. If you want back to main menu, please hold MENU
button for 1 second.

7 E
4.6 Test setting
Select TEST option, press ENTER button to confirm your selection. The
flash indicator will light up and the unit will test automatically. Wait for
several seconds self-test, it will return to main interface. If you want back to
main menu, please hold MENU button for 1 second.
4.7 Temperature
Select the LEMP, press ENTER button and the display will show the
temperature of unit. Wait for 30 seconds, it will return to main interface. If
you want back to main menu, please hold MENU button for 1 second.
4.8 Defaults
Select DEF option, press ENTER button, Use UP/DOWN button if you would
like reset defaults,or not. press ENTER button to confirm your
selection. If you want back to main menu, please hold MENU button for 1
second.
4.9 Check the version number
Select the VER, press ENTER button to confirm. You can see the current
version number now (b 10/v 10) and check them by UP/DOWN. Wait for 30
seconds, it will return to main interface. If you want back to main menu,
please hold MENU button for 1 second.
Channel Mode:

8 E
1 Channel Mode
Channel
Value
Function
1
0-5
Blackout
6-250
Flash rate, slow to fast
251-255
Continuous ”Blinder”effect
2 Channel Mode
Channel
Value
Function
1
0-5
Blackout
6-255
Flash rate, slow to fast
2
Flash intensity
0-5
Blackout
6-255
Minimum to maximum
3 Channel Mode
Channel
Value
Function
1Flash intensity
0-5
Blackout
6-255
Minimum to maximum
2Flash duration 0-255 0-650 ms@50 Hz AC, or 0-530 ms@60 Hz AC
3Flash rate
0-5
No flash (single flash with ch. 1)
6-255
0.5-25 Hz@50 Hz AC, or 0.6-30 Hz @60 Hz AC

9 E
4 Channel Mode
Channel
Value
Function
1Flash intensity
0-5
Blackout
6-255
Minimum to maximum
2Flash duration
0-255
0-650 ms@50 Hz AC, or 0-530 ms@60 Hz AC
3Flash rate
0-5
No flash (single flash with ch. 1)
6-255
0.5-25 Hz@50 Hz AC, or 0.6-30 Hz @60 Hz AC
4
Special effects
0-5
No effect
6-50
Ramp up
51-100
Ramp down
101-150
Ramp up-down
151-200
Lightning
201-255
Random
6 Channel Mode
Channel Value Function
1(R)Flash intensity
0-5
Blackout
6-255
Minimum to maximum