ACME IM-5S-ELC User manual

23J
Innovation , Quality , Performance
IM-5S-ELC IM-5W-ELC
IM-5S-HID IM-5W-HID
User Guide
Professional Entertainment Technology

23J
Innovation , Quality , Performance
IM-5S-ELC IM-5W-ELC
IM-5S-HID IM-5W-HID
User Guide
Professional Entertainment Technology

1J 22J

1J 22J

21J
Technical Specifications
Power AC 120V~60Hz AC 230/240/250V~50/60Hz
Fuse 20mm Glass T6.3A 20mm Glass T5A
Lamp HID 150W
ELC 24V 250W
Dimension 290 x 330 x 380 mm
Weight 12 kg
2J
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
2.1 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
5.3 iSolution Operation / Universal DMX Controller
5.4 DMX 512 Configuration
5.5 DMX 512 Connection
6. Troubleshooting
7. Maintenance and Cleaning

21J
Technical Specifications
Power AC 120V~60Hz AC 230/240/250V~50/60Hz
Fuse 20mm Glass T6.3A 20mm Glass T5A
Lamp HID 150W
ELC 24V 250W
Dimension 290 x 330 x 380 mm
Weight 12 kg
2J
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
2.1 Beam Angle
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
5.3 iSolution Operation / Universal DMX Controller
5.4 DMX 512 Configuration
5.5 DMX 512 Connection
6. Troubleshooting
7. Maintenance and Cleaning

3J
1.Safety Instruction
WARNING
yPlease keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
yUnpack and check carefully there is no transportation damage before using the unit.
yBefore operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
yThe unit is designed for use with the HID 150W or ELC 24V 250W (two version). Do not
use any other type of lamp.
yIt’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
yThe unit is for indoor use only. Use only in a dry location.
yThe unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
yDisconnect main power before fuse/lamp replacement or servicing.
yReplace fuse/lamp only with the same type.
yMake sure there is no flammable materials close to the unit while operating as it is fire
hazard.
yUse safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
always by taking its base.
yMaximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
higher than this.
yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during
its operation. Turn off the power and allow about 15 minutes for the unit to cool down
before replacing bulb or serving.
yIn the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.Always
use the same type spare parts.
yDon’t connect the device to any dimmer pack or power pack.
yDo not touch any wire during operation as high voltage might be causing electric shock.
Please read carefully the instruction, which includes important information
about the installation, usage and maintenance.
20J
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
provision of the Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
EN55014-2: 1997A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements

3J
1.Safety Instruction
WARNING
yPlease keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
yUnpack and check carefully there is no transportation damage before using the unit.
yBefore operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
yThe unit is designed for use with the HID 150W or ELC 24V 250W (two version). Do not
use any other type of lamp.
yIt’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
yThe unit is for indoor use only. Use only in a dry location.
yThe unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
yDisconnect main power before fuse/lamp replacement or servicing.
yReplace fuse/lamp only with the same type.
yMake sure there is no flammable materials close to the unit while operating as it is fire
hazard.
yUse safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
always by taking its base.
yMaximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
higher than this.
yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during
its operation. Turn off the power and allow about 15 minutes for the unit to cool down
before replacing bulb or serving.
yIn the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.Always
use the same type spare parts.
yDon’t connect the device to any dimmer pack or power pack.
yDo not touch any wire during operation as high voltage might be causing electric shock.
Please read carefully the instruction, which includes important information
about the installation, usage and maintenance.
20J
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the
provision of the Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
EN55014-2: 1997A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements

19J
7. Maintenance and Cleaning
Maintenance (for HID lamp only):
Ignitor Filter, Ballast, capacitor
A. As the pictures shown above, if the cable or cable joints turned yellow or black, please
replace the cable or cable joints immediately.
B. Do maintain the fixtures every two months and make sure that all the screws and
terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.
Cleaning:
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
yClean with soft cloth using normal glass cleaning fluid.
yAlways dry the parts carefully.
yClean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
4J
Warning
yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
yNever touch bulb with bare fingers as it is very hot after using.
yHot lamp explosion hazard. Do not open the unit within five minutes after switching off.
yDo not start on the unit without bulb enclosure or housing are damaged.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
yDo not look directly at the light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 20
kgs for each unit.

19J
7. Maintenance and Cleaning
Maintenance (for HID lamp only):
Ignitor Filter, Ballast, capacitor
A. As the pictures shown above, if the cable or cable joints turned yellow or black, please
replace the cable or cable joints immediately.
B. Do maintain the fixtures every two months and make sure that all the screws and
terminals have been locked firmly to make sure the normal performance of the fixtures.
Negligence of maintenance would cause malfunction of the fixture.
Cleaning:
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency depends on the
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
yClean with soft cloth using normal glass cleaning fluid.
yAlways dry the parts carefully.
yClean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
4J
Warning
yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
yNever touch bulb with bare fingers as it is very hot after using.
yHot lamp explosion hazard. Do not open the unit within five minutes after switching off.
yDo not start on the unit without bulb enclosure or housing are damaged.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
yDo not look directly at the light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 20
kgs for each unit.

5J
2. Technical Specification
•Voltage：AC 120V~60Hz or 230V/240V/250V~50/60Hz
•Bulb：HID 150W
ELC 24V 250W
•The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together
in master/slave connection, as many as required and run by built-in program chase
sequences automatically or by sound activation through an internal microphone to create
an intelligent effect.
•It can be operated by DMX 512 control or can be used as an individual unit without a
controller.
•Consistent DMX channel enable iRock, iShow and iMove to be link together.
•Features different preprogrammed chase patterns.
•Please use a 3 pin XLR cable/plug when connecting units together.
•Accurate focusable optics system and ultra smooth stepping motors. Fan cooled.
•Pan : 540 deg. Tilt : 270 deg.
•Dimension : 290 x 330 x 380 mm
•Weight : 12 kg
Move Spot Independent gobo wheel with 14 gobos plus open and blackout, including 11
metal, 2 glass and 1 effect gobos with shaking and shutter effect, Independent
color wheel with 11 dichroic colors with rainbow effect.
Move Wash Independent color wheel with 11 dichroic colors with rainbow effect and
independent shutter & dimmer.
2.1 Beam Angle
18J
G. If The pan belt is broken
1. Turn off the main power.
2. Unscrew all the screws (A) and open the base-housing cover (B).
3. Unplug all the connect wires (C) that from the arm to PC board and ignitor.
4. Unscrew the screws (D) that fix the axis gear (E).
5. Change a new belt (F) by going through all connect wires that from the arm to base,
and through the bridge for correct position.
6. Set up the gear axis to the bridge and screwed it. Note : do not press the belt.
7. Put the belt around the axis gear and motor gear.
8. Plug all the connect wires (C) that form the arm to PC board and ignitor.
9. Adjust the pan home position.
10. Screw the base-housing cover (B).

5J
2. Technical Specification
•Voltage：AC 120V~60Hz or 230V/240V/250V~50/60Hz
•Bulb：HID 150W
ELC 24V 250W
•The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together
in master/slave connection, as many as required and run by built-in program chase
sequences automatically or by sound activation through an internal microphone to create
an intelligent effect.
•It can be operated by DMX 512 control or can be used as an individual unit without a
controller.
•Consistent DMX channel enable iRock, iShow and iMove to be link together.
•Features different preprogrammed chase patterns.
•Please use a 3 pin XLR cable/plug when connecting units together.
•Accurate focusable optics system and ultra smooth stepping motors. Fan cooled.
•Pan : 540 deg. Tilt : 270 deg.
•Dimension : 290 x 330 x 380 mm
•Weight : 12 kg
Move Spot Independent gobo wheel with 14 gobos plus open and blackout, including 11
metal, 2 glass and 1 effect gobos with shaking and shutter effect, Independent
color wheel with 11 dichroic colors with rainbow effect.
Move Wash Independent color wheel with 11 dichroic colors with rainbow effect and
independent shutter & dimmer.
2.1 Beam Angle
18J
G. If The pan belt is broken
1. Turn off the main power.
2. Unscrew all the screws (A) and open the base-housing cover (B).
3. Unplug all the connect wires (C) that from the arm to PC board and ignitor.
4. Unscrew the screws (D) that fix the axis gear (E).
5. Change a new belt (F) by going through all connect wires that from the arm to base,
and through the bridge for correct position.
6. Set up the gear axis to the bridge and screwed it. Note : do not press the belt.
7. Put the belt around the axis gear and motor gear.
8. Plug all the connect wires (C) that form the arm to PC board and ignitor.
9. Adjust the pan home position.
10. Screw the base-housing cover (B).

17J
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
6J
3. Lamp
Lamp :
HID 150W
ELC 24V 250W
1.Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2.Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.
3.Never operate the lamp without appropriate shielding.
4.Make sure the lamp is located in the center for the best spot.
Diagram for Lamp changing
In case of replacement of the lamp or maintenance, do not open the fixture
within 15 minutes until the unit cools down after switching off.

17J
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
6J
3. Lamp
Lamp :
HID 150W
ELC 24V 250W
1.Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2.Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.
3.Never operate the lamp without appropriate shielding.
4.Make sure the lamp is located in the center for the best spot.
Diagram for Lamp changing
In case of replacement of the lamp or maintenance, do not open the fixture
within 15 minutes until the unit cools down after switching off.

7J
HID 150W Lamp Installation Or Replacement
•Always switch power off before installing or replacing the lamp. Never try to replace the
lamp when it is hot.
•Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe
with a lint free cloth when lamp is dirty.
1. Loose the screw on the housing cover.
2. Loose the screws of the lamp wire from terminator
3.Remove the old lamp from the fixture.
4. Please be care to install the lamp into case, make sure it wedge tightly that it
can not move easily. WARNING: impropriety install will cause the lamp
lifespan shorten and maybe explosion during operation.
5. Connect the lamp wire to the terminator as before.
6.Please reinstall step 2 and step 1.
16J
5.5 DMX512 Connection
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1
3
2
OUTPUTINPUT
DMX512
Termination reduces signal errors and to avoid signal
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
transmission problems and interference. It is always
3
pin3 (DMX+) of the last fixture.
advisable to connect a DMX terminal.
2
DMX -
1
COMMON
DMX +
3
1
120 ohm 1/4W
2
1234
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

7J
HID 150W Lamp Installation Or Replacement
•Always switch power off before installing or replacing the lamp. Never try to replace the
lamp when it is hot.
•Do not touch the bulb with bare hands. Cleaning the lamp with denatured alcohol and wipe
with a lint free cloth when lamp is dirty.
1. Loose the screw on the housing cover.
2. Loose the screws of the lamp wire from terminator
3.Remove the old lamp from the fixture.
4. Please be care to install the lamp into case, make sure it wedge tightly that it
can not move easily. WARNING: impropriety install will cause the lamp
lifespan shorten and maybe explosion during operation.
5. Connect the lamp wire to the terminator as before.
6.Please reinstall step 2 and step 1.
16J
5.5 DMX512 Connection
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1
3
2
OUTPUTINPUT
DMX512
Termination reduces signal errors and to avoid signal
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
transmission problems and interference. It is always
3
pin3 (DMX+) of the last fixture.
advisable to connect a DMX terminal.
2
DMX -
1
COMMON
DMX +
3
1
120 ohm 1/4W
2
1234
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

15J
5.4 DMX 512 Configuration
Item Ch 1 Ch 2 Ch 3 Ch 4 Ch 5 Ch 6 Ch 7
Move Spot Pan Tilt Shutter/Sharking Gobo Color
Move Wash Pan Tilt Shutter No function Color No function Dimmer
8J
4. How To Set The Unit
4.1 Control Panel
Display
To show the various menus and the selected functions.
LED
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Remote controller input
By connect to the 1/4” microphone jack to control the unit for stand by, function and mode
Sensitivity
To adjust the sound sensitivity.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.

15J
5.4 DMX 512 Configuration
Item Ch 1 Ch 2 Ch 3 Ch 4 Ch 5 Ch 6 Ch 7
Move Spot Pan Tilt Shutter/Sharking Gobo Color
Move Wash Pan Tilt Shutter No function Color No function Dimmer
8J
4. How To Set The Unit
4.1 Control Panel
Display
To show the various menus and the selected functions.
LED
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Remote controller input
By connect to the 1/4” microphone jack to control the unit for stand by, function and mode
Sensitivity
To adjust the sound sensitivity.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.

9J
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are showing below:
MENU
Focus Adjust
Self-Test
Reset
Fixture Hours
Display Inversion
Display Normal
Tilt Inversion
Tilt Normal
Pan Inversion
Pan Normal
Split Color
Normal Color
Show mode 4
Show mode 3
DMX512 Address Setting
Blackout Mode " No Blackout "
Blackout Mode " Yes Blackout "
Slave Mode " Normal "
Slave mode " 2 Light Show "
Show mode 1
Show mode 2
LED off
LED on
Dimmer Normal
Dimmer Inversion
DMX 512 Address Setting
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
14J
Stand by Blackout the unit
Function
Strobe
1.Gobo / Color
sync.
strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving show
mode selection
( Show 1 ~ Show
4 )
Please refer to
Show mode in
4.2 Main Function
Color/Gobo
selection
1. Hold on for gobo
change.
2. Press shortly for
color change
X/Y moving setting
1.Pan position
2.Tilt position
First set Master
unit, then set Slave
units’ position
Move
Spot
Mode Sound 1
(LED off ) Sound 2 (LED normal
blinking)
Slow/Sound 3
(LED on) Position/ Latch (LED fast blinking)
Stand by Blackout the unit
Function
Strobe
1.Color sync.
strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving show
mode selection
( Show 1 ~ Show
4 )
Please refer to
Show mode in
4.2 Main Function
Color selection
X/Y moving setting 1.Pan position
2.Tilt position
3.Dimmer
First set Master
unit, then set Slave
units’ position
Move
Wash
Mode Sound 1
(LED off ) Sound 2 (LED normal
blinking)
Slow/Sound 3
(LED on) Position/ Latch (LED fast blinking)
5.3.1 iSolution Operation
♦Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to setDMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.

9J
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are showing below:
MENU
Focus Adjust
Self-Test
Reset
Fixture Hours
Display Inversion
Display Normal
Tilt Inversion
Tilt Normal
Pan Inversion
Pan Normal
Split Color
Normal Color
Show mode 4
Show mode 3
DMX512 Address Setting
Blackout Mode " No Blackout "
Blackout Mode " Yes Blackout "
Slave Mode " Normal "
Slave mode " 2 Light Show "
Show mode 1
Show mode 2
LED off
LED on
Dimmer Normal
Dimmer Inversion
DMX 512 Address Setting
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
14J
Stand by Blackout the unit
Function
Strobe
1.Gobo / Color
sync.
strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving show
mode selection
( Show 1 ~ Show
4 )
Please refer to
Show mode in
4.2 Main Function
Color/Gobo
selection
1. Hold on for gobo
change.
2. Press shortly for
color change
X/Y moving setting
1.Pan position
2.Tilt position
First set Master
unit, then set Slave
units’ position
Move
Spot
Mode Sound 1
(LED off ) Sound 2 (LED normal
blinking)
Slow/Sound 3
(LED on) Position/ Latch (LED fast blinking)
Stand by Blackout the unit
Function
Strobe
1.Color sync.
strobe
2.Sync. strobe
3.Two-light strobe
X/Y moving show
mode selection
( Show 1 ~ Show
4 )
Please refer to
Show mode in
4.2 Main Function
Color selection
X/Y moving setting 1.Pan position
2.Tilt position
3.Dimmer
First set Master
unit, then set Slave
units’ position
Move
Wash
Mode Sound 1
(LED off ) Sound 2 (LED normal
blinking)
Slow/Sound 3
(LED on) Position/ Latch (LED fast blinking)
5.3.1 iSolution Operation
♦Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to setDMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.