ACME LED-LP400 User manual

LED-LP400
User Manual
Please read it carefully before using

1A

Contents

1. Safety Introductions ............................................................................................................2
2. Technical Specifications.......................................................................................................3
3. Installation ..........................................................................................................................3
4. How To Set The Fixture .......................................................................................................4
4.1 Control Panel.................................................................................................................4
4.2 Main Function ...............................................................................................................5
5. How To Control The Unit....................................................................................................8
5.1 Master/Slave Function ...................................................................................................9
5.2 DMX Controller.............................................................................................................9
6. DMX512 Configuration .....................................................................................................10
7. DMX512 Connections.......................................................................................................10
8. Troubleshooting ................................................................................................................11
9. Fixture Cleaning ................................................................................................................12













2A

1. Safety Introductions
WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
The unit is for indoor use only and use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect mains power before fuse replacement or servicing.
Replace fuse only with the same type.
Make sure there are not flammable materials close to the unit while operating as it is fire
hazard.
Use safety cable when fixes this unit.
Maximum ambient temperature is TA: 40 and don’t operate it where the temperature is
higher than this.
There are no user serviceable parts inside the fixture. Do not open the housing or attempt
any repairs by yourself. In the unlikely event your fixture may require service, please
contact the nearest authorized technical assistance center and always use the same type
spare parts. .
Don’t connect the device to any dimmer pack or power pack.
Do not look directly at the LED light beam while the fixture is on.
The housing must be replaced if they are visibly damaged.
Do not touch any wire during operation as high voltage might be causing electric shock.
Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.

3A

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage
unit.




2. Technical Specifications
It can be operated by DMX512 control or can be used as an individual unit without
controller.
It can be linked together as many as required in master/slave mode, and perform the great
built-in programmed lighting shows triggered by music.
Please use a 3 pin XLR cable/plug when connecting them together.
It features different pre-programmed chase patterns.
2/3 Channel modes.
Voltage: AC 100V-240V,50/60Hz
LED: 400pcs
Power consumption󵽱26W
Fuse: T 6.3A
Dimension 406 x 356 x 114mm
Weight󵽱 6.2KG

3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of the
unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit
when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of
the touch of people and has no one pass by or under it.
For230V50Hzpowersupply,maximumfixturesthatcanbeconnectedononepowercableis20;
For120V60Hzpowersupply,maximumfixturesthatcanbeconnectedononepowercableis12;

4A

4. How To Set The Fixture
4.1 Control Panel


1.Display: Used to show the various menus and the selected functions;
2. Indicator LED:
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
COLOR TEMP. Flashing Max. power consumption of CW/WW
3. Button:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
4. Battery Switch: Used to connect or disconnect the battery power supply.
5. Dimmer Adjust Knob: Used to adjust lightness for the unit.
6. Color Adjust Knob: Used to adjust the color temperature from 3200k to 6500k,
7. DMX Output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.
8. DMX Input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal
9. Mains Output: Used to provide power supply for the next machine.
10. Mains Input: Used to connect to supply mains power.

5A

11. Safety Hook: Ensure the safety of the fixture installation.

4.2 Main Function
To select any functions, press the MENU button until the required one is shown on the display.
Select the function by the ENTER button and the display will blink. Use the DOWN and UP
button to change the mode. Once the required mode has been selected, press the ENTER
button to setup or it will automatically return to the main functions without any change after
idling 30 seconds. Back to the functions without any change press the MENU button.
The main functions are shown below:

6A



DMX 512 Address
Press the MENU button up to when the is shown on the display. Press the ENTER
button and the display will blink. Use the DOWN and UP button to change the DMX 512
address. Once the address has been selected, press the ENTER button to setup or
automatically exit menu mode without any change after 8 seconds. Back to the previous
functions without any change press the MENU button.

7A

Channel Mode
Press the MENU button up to when the is shown on the display. Press the ENTER
button and the display will blink. Use the DOWN and UP button to select the (2
channels) or (2 channels) or (3 Channels) mode. Once the mode has been
selected, press the ENTER button to setup or automatically exit menu mode without any
change after 8 seconds. To go back to the functions without any change press the MENU
button.
Manual Mode
Press the MENU button up to when the is shown on the display. Press the ENTER
button and the display will blink. Use the DOWN and UP button to select the or
or (dimmer) mode, press the ENTER button to confirm, use the UP and DOWN
button to adjust the value between 0 and 255, once select press the ENTER button to setup or
automatically exit menu mode without any change after 8 seconds. To go back to the
functions without any change press the MENU button.
DMX State
Press the MENU button up to when the is shown on the display. Press the ENTER
button and the display will blink. Use the DOWN and UP button to select the
(Master/Slave Mode)  Blackoutor ( remain the last state when exiting the
menu). Once select press the ENTER button to setup or automatically exit menu mode
without any change after 8 seconds. To go back to the functions without any change press the
MENU button.
LED display
Press the MENU button up to when the is shown on the display. Press the ENTER
button and the display will blink. Use the DOWN and UP button to select the (display
on) or (display off) mode. Once select, press the ENTER button to setup or exit menu
mode without any change after 8 seconds. Back to the functions without any change press the

8A

MENU button again.
Display Inverse
Press the MENU button until the is blinking on the display. Use the DOWN and UP
button to select the (normal) or (inverse), press the ENTER button to setup.
Back to the functions without any change press the MENU button.
Auto Test
Press the MENU button up to when the is blinking on the display. Press the ENTER
button and the unit will run the built-in programmer for self-test. To go back to the functions
press the MENU button.
Fixture use time
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button.
Software version
Press the MENU button up to when the is blinking on the display. Press the ENTER
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button again.

5. How To Control The Unit
You can operate the unit in two ways:
1. By master/slave function
2. By DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be affected at once. Every time you turn the unit on, it will show type on the display. After
that the unit will be ready to receive DMX signal or run the built in programs.

9A

5.1 Master/Slave Function
By linking the units in master/slave connection, the first unit will be master automatically. You
should set the master unit effect via its knobs, then the other units (slave) will lighting as the
same.
5.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from 1 to 512
channel so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when the
display stops blinking or storing automatically 30 seconds later. To go back to the functions
without any change press the MENU button again.
If you use please refer to the following diagram to address your DMX512 channel for the first
4 units.

2channels:
3channels:













10A

6. DMX512 Configuration
2/3 Channels Mode:


7. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.



11A

1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily
distort the signal and shut down the system
2. The DMX output and input connectors are pass-through to maintain the DMX circuit
when one of the units’ power is disconnected.
3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
4. Each lighting fixture needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
5. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin4/5: not used

8. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and DMX
polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of

12A

the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.
C. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
D. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.

9. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60
days.




































Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55103-1: 2009 ; EN55103-2: 2009; EN62471: 2008;
EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.
&
Harmonized Standard
EN 60598-1:2008 + All:2009; EN 60598-2-17:1989 + A2:1991; EN
62471:2008; EN 62493: 2010
Safety of household and similar electrical appliances
Part 1: General requirements


Innovation, Quality, Performance
