Acnodes KDM82712 User manual

All rights reserved. Product description and product specifications aresubject to changewithout notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710 Tel: [phone] Fax: [phone]
© C opyright 2015 Acnodes C orp.

Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the
contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from
the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■ Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power fluctuation or failure.
□Use of supplies or parts not meeting our specifications.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Contents
< Part. 1 > KDM82712
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Installation
P.1
P.1 - 2
P.3 - 5
< Part. 2 > Specifications / OSD
2.1 Product Specifications
2.2 Keyboard / Mouse Specifications
2.3 On-screen Display Operation ( OSD )
P.6- 7
P. 8 - 10
P. 11 -12
< Part. 3 > Options
3.1 48V, 24V or 12VDC power
< Part. 4 > KVM Integration
4.1 KVM port connection
4.2 Specifications
4.3 KVM Button
4.4 KVM Hotkey
4.5 DC power 12V, 24V, 48V Input
P. 13
P.14
P.15
P.16
P.17
P.18

Before Installation
■It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
■Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, pleasefollow these steps :
1 Disconnect the power cord.
2 Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges,please follow these steps :
1 Disconnect the power cord.
2 Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not sprayor apply any liquids directlyonto themonitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3 Gently wipe the surface. Use as little pressure as possible.
4 Waituntil your monitor is completely dry before plugging it in and powering it up.

6
7
8
9
< Part 1 >
< 1.1 > Package Content
KDM82712 unit X1
- 6ft DVI-D console cable X 1
- Power cord X 1
- M6 screw, cage nut & cup washer X 8
< 1.2 > Structure Diagram
5
1
2
3
4
5
1 Carry handle to release the 2-pt lock
6
Audio speaker ( for HDMI or Audiooption )
2 LCD interchangeable module kit
7
Keyboard interchangeablemodulekit
3 Installation Slides
8
Touchpad mouse module
4 LCD membrane
5 Membrane switch (KVM option)
9 1U dual slide for LCDconsole drawer

< 1.2 > Dimension
Front View
Side View
Top View
UNIT: mm
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
KDM 82712
441.6 x 650 x 44 mm
17.4 x 25.6 x 1.73"
595 x 860 x 140 mm
23.4 x 33.9 x 5.5”
14 kg
31 lb
20 kg
44 lb

< 1.3 > Installation - How to install Installation Slides
Step 1
¦ Insert the left and right rear mounting bracketsinto
the LCDconsole drawer.
Step 2
¦ Measure the depth of the front and rear mountingrails.
¦ Align each rear mounting bracketto a suitable length.
Step 3
Complete the installation
¦ Fix the LCD console drawer into the rack.
M6 screw, cage nut & cup washerx 8 are provided.

< 1.3 > Installation - How to Use the Dual Slides
¦ Press the handle button and gentlyslide out
the drawer.
¦ Flip up the LCD to a suitable angle.
¦ Operatethe LCD consoledrawer.

< 1.3 > Installation - How to Use the Dual Slides
¦ Flip down the front panel.
¦ Press the handle button and gently push
back the drawer into the rack.
¦ Return the LCD console drawer to park
position.

< Part 2 >
< 2.1 > Product Specifications
LCD
Panel Panel Size ( diagonal ) 17.3-inchWidescreenTFT color LCD
Displaypixel ( dots x lines ) 1920 x
1080
Brightness ( typ. )
300
Contrast Ratio ( typ.)
600:1
Color 1.07 Billion,
10-bit
ViewingAngle ( L/R/U/D )
89/89/89/89
ResponseTime( ms )
35
Dot pitch ( mm )
0.199
DisplayArea ( mm ) 381.9H x
214.8V
Surface treatmentAnti-glare, Hard-coating
Surface hardness
3H
BacklightType
LED
MTBF ( hrs )
20,000
Video
Connectivity Digital DVI DVI-D, TMDS single link
Audio
Connectivity AudioInput Connector 3.5mm stereo jack
Impedance/ Power level 30kΩ/ 750mV
AudioOutput Connector 3.5mm stereo jack
Resistance/ Power level 30kΩ/ 2.8V
Speaker Output Power 2 x 2W
*When the audio output is connected, speaker output is OFF
Power Power Supply Range Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption Screen display ON 34W or less
Power savingmode 4W or less
Powerbutton OFF1W or less
Regulatory Safety Approval FCC & CE

Environmental
Conditions Operating Temperature 0 to 50°C degree
Humidity 20~90%,non-condensing
Storage Temperature -5 to 60°C degree
Humidity 5~90%, non-condensing
Shock 10G acceleration (11ms duration)
Vibration 5~500Hz 1G RMS random
Physical
Specification Product ( W x D x H) 441.6 x 650 x 44 mm
17.4 x 25.6 x 1.73 inch
Packing ( W x Dx H ) 595 x 860 x 140 mm
23.4 x 33.9 x 5.5 inch
Net Weight 14 kgs / 31
lbs
Gross Weight 20 kgs / 44
lbs
Applicable
Format DVI-D / VGA Input PC Signal 1920 x 1080 x 60Hz
1360 x 768 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz

< 2.2 > Keyboard / Mouse Specifications
Ge G keyboard integrated with touchpad
Keyforce
55 ± 5g
Travellingdistance
3 ± 0.3mm
Switch life
> 10 million life cycletime
Software support
MS Windows7 / 2008 / 2003 / 2000 / XP / ME / 98 / DOC
Linux / Mac
Supporting layouts
America
EMEA
Asia
UnitedStates
United Kingdom Germany France Spain Norway
Italy Russia Switzerland Netherlands Portugal
China Japan Korea Arabia Turkey

F 7 F8
< 2.2 > MAC Keyboard / Mouse Options
Me MAC keyboard integrated with touchpad
Supporting layouts
America UnitedStates
How to Use "MAC" Keyboard
Keyboard Features
F1
Decreasedisplay brightness
F2
Increase display brightness
F3
Mission control
* Only works with OS X Lion
default KeyboardShortcuts.
F4
Dashboard
F9
Fast-forward
F10
Mutesound
F11
Decrease volume
F12
Increase volume
F7
Rewind Eject disc
F8
Play / Pause Command

Nu m Ca ps S crol l C om po se
< 2.2 > SUN Keyboard / Mouse Options
Se S keyboard integrated with touchpad
S keyboard integrated with touchpad / trackball
¦ IncorporatesSUN keys, including Stop, Cut, Paste, Compose, Copyand Help
¦ 104 key notepad keyboard with full numericalpad and SUN function
¦ USB interface
¦ US layout only
How to Use "S" Keyboard
Num LED in Off mode
Key pad behaves as a SUN Solar
system administration command mode
Num LED in Green mode
Key pad behavesas a normalkey
pad mode
Audio / Display Keys * Please ask your supplier for full details
F9
Audio : Mute
Display : Degauss
F11
Audio : Decrease volume
Display : Decreasecontrast
F12
Audio : Increase volume
Display : Increase contrast

< 2.3 > On-screen DisplayOperation ( OSD )
Membrane Switch Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menuor
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power touch button will flash continuously when there is no signal input.
1 All the LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power ).
2 Light up all membranebuttons, please press any button for 1 - 2 seconds ( except the Power ).
1
Picture
Picture mode :
Standard / Vivid / Soft / User mode to choose
Brightness :
Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
(black level) and the foreground (white level)
Hue:
Adjust the screen hue value
Saturation :
Adjust the saturation of the image color
Picture size :
Adjust the image size
Color temp :
Standard / Cool / Warm / User to choose
Noise reduce :
Reduce the noise of the image
Sharpness :
Adjust the image from weak to sharp

< 2.3 > On-screen Display Operation ( OSD )
2
PC
Auto adjust :
Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock :
Adjust the clock value
Phase :
Adjust the phase value
H.Position :
Align the screen image left or right
V.Position :
Align the screen image up or down
3 Audio
Audio mode : Movie / Voice / Normal / Music mode to choose
Volume : Adjust the volu me of sou nd
Bass : Set the value of bass sound
Treble : Set the value of treble sound
Balance : Set the balance value of trebleand bass sound
Analog TV audio : Set the value of analog TV audiosound
Mute : Turn off the surrounding sound
4
MISC
Language :
Select the language in which the OSD menu is
displayed - English
Sleep timer :
Set the off time
PIP mode :
Adjust picture in picture setting
PIP position :
Enter into PIP position
PIP source :
Enter into the Sub source and sound source
System reset :
Return the adjustment back to factory setting
Information :
Select for Help

<Part 3>
< 3.1 > Options : DC Power
Model
12V 24V 48V
Input rating
Input voltage: 12-Volt 24-Volt 48-Volt
Input range: 9 ~ 18V 18 ~ 36V 36 ~ 75V
Input current
- No load 50 mA 50 mA 50 mA
- Full load 4950 mA 2450mA 1220 mA
Output rating
Output voltage: 12-Volt 12-Volt 12-Volt
Output current: 4.16A 4.16A 4.16A
Efficiency 84%85%85%

12 11 10 9 8 7
<Part 4> KVM Integration
< 4.1 > KVM port connection
USB Servers
DVI-D KVM port
Power Audio
6 5 4 3 2 1
USB Servers
DVI KVM Cable
6 feet DVI KVM cable
15 feet DVI KVM cable
( Server end : DVI-D + USB + Audio )
( KVM port : DVI-D + USB3.0 )
IP console,remoteconsole,daisy-chain and OSDmenuare NOT available for this model.

< 4.2 > Specifications
KVD1201
¯ KVM Port
Number of ports: 12
Connector: DVI-D connector
USB 3.0 connector( combined for keyboard, mouse & audio )
Connectivity: Combo 4-in-1, KVM cable, 6 or 15 feet
¯ Audio Out 1 x 3.5mm stereo audio
¯ Management
PC Selection: Frontbutton & keyboard hotkey
¯ Compatibility
Multi-platform : Mix PCs, SUN and Mac G3 / G4 Mac / iMac
Support: Windows 7 / Vista / 2003 / XP, Linux,Unix
¯ Power
Input: 100 or 240V AC at 50 or 60 Hz via IEC type cord
Option DC: 12V / 24V / 48V DC input
Consumption: Max.48 Watt,Standby5 Watt
¯ Regulatory Approval: FCC, CE
¯ Environmental
Operating: 0 to 50°C
Storage: -5 to 60°C
Relative humidity: 90%, non-condensing
Shock: 50G peak acceleration(11ms, half-sine wave)
Vibration: 58~100Hz / 0.98G (11ms / cycle)

4.3 KVM Button
Power ON
¦ Turn off all servers and KVM switches
¦ Make sure all cables / connectors are properly connected
¦ Recommend Power ON sequence is monitor, KVM switch finally computer
Front Panel - Port LED Indications
DVI-D KVM 12 ports
PC port LEDs Channel
button Button B is
non-functional
PC port LEDs Online: Blue LED on indicating a PC is connecting to the port
Active : Green LED on indicating a selected channel
Channel button Press to select channel from 01 to 12